Search results

Results 401 to 450 of 500
  1. ILENGINE

    Fuel line

    Most of the time the fuel pickup coming from the top of the tank to the bottom is just a black hard or somewhat hard plastic line. And make sure you have a replacement grommet for the tank when you remove the fuel line insert since most of the time the grommet tears upon removal.
  2. ILENGINE

    Is this wire connected correctly?

    The engine that originally came on that mower had the 3/5 dual circuit non regulated charging system. The current engine is a 9 amp regulated system. So original wiring diagram for the mower will not be accurate for this application. And the fuse should be located in the area of the battery...
  3. ILENGINE

    Where is my model number?

    What is the model type and code from the metal flap on the engine. Sometimes the SBD model number can be located by cross referencing the engine model number.
  4. ILENGINE

    Husqvarna YTH2448 Carb

    Part number 699709 is the downward facing fuel solenoid but appears to supercede to 791230 which appears to be a side facing fuel solenoid.
  5. ILENGINE

    Is this wire connected correctly?

    Yes. The regulator has built in diodes that take the place in the wire. If you want you can disconnect the red connector at the VR, and run a wire directly that connector to the + battery connector and with the engine running see if the battery now is charging.
  6. ILENGINE

    Is this wire connected correctly?

    Is that a diode inside that shrink wrap on the front connector. I hope it isn't connected in series with the voltage regulator or it will never charge.
  7. ILENGINE

    Removing the fuel filter

    I think I still have the one around here that I made with an angle grinder using a flat piece of steel.
  8. ILENGINE

    Stihl chainsaws

    The big issue is making sure that seat properly when reinstalling after fueling, otherwise they like to dump the gas down your leg.
  9. ILENGINE

    Toro LX 420

    What is funny is that part number is also the part number for the MTD bagger.
  10. ILENGINE

    Removing the fuel filter

    May not of been meant for me, but the kohler fuel fllter wlll not damage your mower, and may even be a better filter than what is on there now. Have sold many of that exact part number over the years. Have used them on all brands of mowers over the past 28 years.
  11. ILENGINE

    Murray with B&S won't Charge Battery

    3 things to check. Is the new voltage regulator grounded The 5/9 regulator has a red and yellow wire that normally mounts next to the dipstick tube. There is a single screw that attaches it. There should be a grouding wire that attaches to the screw. Are you getting 12 volts from the wire...
  12. ILENGINE

    Removing the fuel filter

    Need to be careful about twisting the fuel line onto or off of fittings because with the modern low perm fuel lines it can damaged the plastic liner which causes it to collapse or break apart into pieces and end up in places that cause problems later.
  13. ILENGINE

    Removing the fuel filter

    I use this to pry most fuel lines loose from the fuel filter fittings. https://www.jackssmallengines.com/jacks-parts-lookup/part/briggs-stratton/19620
  14. ILENGINE

    Kohler ignition repair kit for 22 hp Courage engine

    According to Kohler your engine doesn't use the spark advance system it is a fixed timing CDI system Which uses two 24 584 45-S ignition modules. So neither one of the part numbers that you referenced apply to your engine.
  15. ILENGINE

    Walbro LMT-34 needle

    What is the model and type of the briggs engine. The carb parts are ordered by model number of the engine. In some cases the carb numbers are used as a reference only when looking up the briggs part number
  16. ILENGINE

    Kohler ignition repair kit for 22 hp Courage engine

    Lets not get the cart before the horse. What is the model and spec of your Courage engine so we can confirm that is actually the kit you need.
  17. ILENGINE

    Briggs &Stratton Has Slight "Pop-Pop-Pop" When Running

    Compression test is not a good test for those style engines. Leakdown testing is the better test. Would tell you if you have compression leaks and were. With that age I would just remove the head and take a look at the cylinder walls looking for wear and a ridge at the top of the cylinder...
  18. ILENGINE

    Briggs &Stratton Has Slight "Pop-Pop-Pop" When Running

    After 26 years I suspect that it is floating the intake valve and is not sealing. Over time the valve face and seat wear which results in the valve clearance getting narrower until it can not longer close the valve.
  19. ILENGINE

    Not starting with new battery

    I would start by checking the fuses. Sounds like something shorted out and blew a fuse,
  20. ILENGINE

    Need source for blade drive pulleys for Rider 14 PRO with 41" deck-2000 model?

    Im a HCP service center so have access to Husqvarna parts not exclusively used on Husqvarna branded products. If I tryt to purchase a Husqvarna exclusive part my distributor gives me the restricted warning.
  21. ILENGINE

    Loses power

    So what model of mower and what engine do you have with model number if possible
  22. ILENGINE

    Need source for blade drive pulleys for Rider 14 PRO with 41" deck-2000 model?

    My husqvarna distributor shows NLA also and they are an official Husqvarna distributor.
  23. ILENGINE

    Intake Elbow hose

    If it is a small hose that comes out the end of the elbow most likely that is the emission hose that connects to the either the top of the fuel tank or to a canister that looks like a small black box mounted to the engine that has another hose that connects to the top of the fuel tank.
  24. ILENGINE

    Mower drive belt problems

    160855 supercedes to 532138255
  25. ILENGINE

    Kohler 7000 Series 24hp KT735-725cc

    How many pins are present in the 6 pin white connector. Should have 5 pins used.
  26. ILENGINE

    No spark from the plug but strong spark from the coil.

    The blink style testers cannot be used connected between the spark plug wire and grounded. It takes like nothing to blink the light since the tester basically doesn't have any resistance. So from your description I would be replacing the coil.
  27. ILENGINE

    Cub cadet xt2 drive belt system

    Need the model and serial number from tag under seat. Is this a hydrostat or the 2 belt drive system with variable speed stack pulley. And if the 2 belt system I hope you replaced both belts.
  28. ILENGINE

    Murray MT100 deck belt replaced and stopped working

    Make sure the deck is not engaged. Will prevent cranking.
  29. ILENGINE

    chain saw chain recommendations?

    The stump from about 6 inches above ground level to the roots will include dirt, rocks and foreign material that will dull the chain quickly. The box store chains that everybody likes to buy is the lower grade of the 3 grades of chain that Oregon produces. First confirm what @MParr mentioned...
  30. ILENGINE

    Craftsman carburetor linkages

    Which one of the thousands of Craftsman mowers that have been made over the last 80 years are you working on.
  31. ILENGINE

    mower just died running

    From your description either the bottom relay isn't operating or you are not getting power from the time delay module. Or possibly the time delay module isn't getting power from its source.
  32. ILENGINE

    2016 exmark Lazer z starter wiring

    If you have a volt meter. Then connect the negative wire to the negative terminal of the battery. It will remain there for all the following testing. First connect the red test lead to the positive post of the battery, what is the voltage. Now engage the starter and what is the voltage. Now...
  33. ILENGINE

    2016 exmark Lazer z starter wiring

    Remove all the wires that you connected to the starter and if you have a Ohm meter then put the red lead on the large lug furthest from the starter motor, and then touch the black lead to the case of the starter solenoid or starter body. Do you have 0 ohms or something close to that. If so...
  34. ILENGINE

    2016 exmark Lazer z starter wiring

    My best guess is the large red from battery, the small red and the purple wire connect to the large starter solenoid lug furthest from the starter body. The large black and small black connect to a starter mounting bolt. The exciter wire connects to the spade terminal on the starter.
  35. ILENGINE

    MTD Yard Machine model 13A6672G129 and no manual. MTD says no serial #, no manual. Please help

    If you are trying to use the MTD website to look up the owners manual then you can put the model number in the proper field, and then put eight zeroes in the serial field.
  36. ILENGINE

    cub cadet poor customer service

    I have probably played the same game.
  37. ILENGINE

    cub cadet poor customer service

    I can understand the fustration but SBD has been known to contact dealers distributors to find out if the dealer actually ordered the parts from their authorized distributor. or request copies of the parts invoice as part of warranty procedures. Failure to provide proper documentation has...
  38. ILENGINE

    Parts help

    Mistype. Have corrected my original post with incorrect number
  39. ILENGINE

    BR600 help.

    Have you checked the exhaust screen to make sure it isn't carbon plugged.
  40. ILENGINE

    cub cadet poor customer service

    Warranty most of the time will pay for additional damaged items that are a consequence of the initial failure as a single event.
  41. ILENGINE

    cub cadet poor customer service

    I can feel your pain. From a service center observation. Dealers often get caught in the middle, and customers blame the dealer for things that are beyond their control. In other words customers like to blame the dealer for things that the OEM made the decision to deny the warranty.
  42. ILENGINE

    cub cadet poor customer service

    I understand your fustration with lack of parts availability. And the delays lead to additional issues. Now I have a question if you would of sent pictures of the damaged wheel yokes to SBD for warranty consideration for defect and workmanship would they of been considered a failure of...
  43. ILENGINE

    Parts help

    This is the bent part Part number 71599 and the spring is part number 51605
  44. ILENGINE

    cub cadet poor customer service

    I am interested in what happened to the front forks. A picture woud be worth a thousand words.
  45. ILENGINE

    KOHLER Command Pro 26 EFI CH26 Backfiring and Bogging down/losing power

    There is a bulletin hilighting a water intrusion issue into the ecu plug causing a misfire, or can progess into entering the ECU itself preventing starting and running of the CH26 prior to 2000 on exmark laser Z and toro mid-mount Z mowers.
  46. ILENGINE

    KOHLER Command Pro 26 EFI CH26 Backfiring and Bogging down/losing power

    The early Bosch systems used a 2 digit blink code followed by the 61 end test code. And to the OP 23 blink code indicates defective ECU. The 4 digit P code would be a P0601
  47. ILENGINE

    2000 Kohler 15.5hp valve gap adjustments

    You definitely don't know Kohler engines. The Kohler command has always used hydraulic lifters and the same style lifters used on auto engines to this day. And they were not used on lower end mowers. The Command is considered the flagship engine and they were used on lower end mowers...
  48. ILENGINE

    2000 Kohler 15.5hp valve gap adjustments

    No it was a 15 HP engine that Craftsman got caught lying about HP and one of the reasons the small engine companies and Sears got sued. Craftsman changing the HP ratings of engines on their products was the primary defendent of the HP lawsuit. And did you know that Kohler was the only company...
  49. ILENGINE

    KOHLER Command Pro 26 EFI CH26 Backfiring and Bogging down/losing power

    Is the MIL light illuminated. That can give us direction for fault codes. And stop doing the shotgun parts replacement until we have more information to go on. Like are you loosing fire and that is the reason you are replacing the ignition modules. And lets find out compression but I...
  50. ILENGINE

    Craftsman M230 Flywheel/Shroud/Blade Shaft noise?

    If this engine has a Briggs engine and the starter rope is attached to the push handle. Remove the rope from the handle and let it retract into the engine and see it still makes that metallic rub sound. I suspect that the pawls of the SUSA starter are making contact when the push handle is...
Back
Top