Search results

Looking for thoughts on why my ex mark shut of while mowing. I didn’t hit anything, inwas Mowing and engine just shut off. I tried to restart and I hear a clicking noise similar to when trying to start mower with low or dead battery. Battery voltage reads 12.4 but when key is turned to start...

My Stihl weedeater runs fine but won’t shut off. I have checked continuity from the yellow wire grounded to the motor to the switch and it is good. I have continuity on the black wire that plugs into the coil and goes to the kill switch, it good as well. When I push the kill switch down I...

How do I get proper timing set for my Gcv 200. Mower model HRX217K6HYA. It is very hard to pull through compression stroke. I am not certain I reassembled engine correctly. Would the cam release spring also cause this? Is there a site I can get to to read about proper reassembly instructions for...

Sat for a couple of years. Acts like hydro lock, turns over about one stoke then stops. Carb was leaking by in oil sump. Drained oil and refilled with new. Let it sit overnight. Checked oil no gas in sump. Still same thing, so I set valves. I can see the compression release working when I turn...

My kawasaki on my gravley ztr will run fine at start up After about 2 hours of running it will start to back fire, miss and the will shut down and will not restart untill it cools down. Usually have to wait 8 to 10 hours before it will restart and run fine. Anyone have any ideas on what's...

HELLO ALL . I am stumped on this on. my exmark with a v735 kawasaki on it has an electrical issue I can not find. Yesterday ran all day no problem. Today it wouldnt start, just clicked. I have been fighting this issue for a cpuple of weeks. Today the new starter got very warm when I attempted...

I need to know how much compression my cylinder should have. I checked it and it shows 60 psi, I think that is low. Does anyone know what the compression number should be is on my gcv190?

When running the deck ony 46 the long portion of the belt is slapping around alot. Souxh so that it's breaking the belt. Got new belt from shop but same issues. Have replaced belt and tensioner spring on deck but help. Anyone got any Ideas?

I have a craftsman push mower that has the thermostat controlled choke mechanism on it. The issue is that when the engine is hot the thermostat will not allow the choke arm to go to choke position so that it will start when hot. The thermostat arm remains forward thus keeping the choke arm...

I am having trouble with carburetor. Can not get it adjusted to run properly. Does anyone have suggestions on how to set Carb on this blower?

Please help. I have an HRX217K5HYAA SERIAL NUMBER MAGA-2735815. Engine model number is GJAAA 3435787. Belongs to a friend who ran it without oil and it locked up. I looked online and found a new engine Model number GSV190LAN1L and need to know if that would fit on the one with locked up...

My HQ has a kohler motor. After motor started missing at high RPM and,sometimes not starting at all I replaced carb. Mowed yard and it,ran great. Next morning won't start., new carb and filter, fuel pump is working or at,least its pumping when I remove fuel line and turn motor over. Any ideas...

I am gettng a Lot of oil from the breather tube that is runs from the crankcase breather to the fuel pump. Does anyone have an idea why this is happening? Oil is literally running out of fuel pump when motor is running. FYI. When I Checked oil level it was very low. About 1 quart low. I...

Hello all. I am working on Exmark mower for a friend of mine. This machine sat for a couple of months without running then it went through hurricane Harvey and was flooded in 4 feet of water. It was running when parked. I have flushed the engine but now have an electrical problem. It will not...

Ok while trying to blow air thru the fuel line back into the tank to clean out some trash. I accidently blew about 20 pounds of air into the intake line and hear a POP which I assume was a gasket of some sort. Now when running oil is leaking out and seems to be coming from some where around the...

ok I have rebuilt the carb. It has spark but will not start, not even try to start. How do I check the coil to see if it is making enough spark to fire engine? I have disconnected the ground and it is making spark. All wires seem to be fine. Its sparks when switch is in the on postion and will...

Hi all. Please help. I am working on my lesco backpack blower. It seems to have lost spark but when I pull the plug and check I see spark until the RPMS die down from me pulling the starter rope. When I leave the plug in and I hook up my spark tester to the plug wire I down see any spark due to...

2007 LT1000. When starting, turn key I hear a clicking noise. After several attempts it will turn over and start. Checked battery 13.02 volts, checked selinoid getting 13.02 into and out of selinoid. So starter or selinoid going out?

I am looking a t a non-running 4514 fo rabout 200.00. It will turn over but not run. I have fixed many riders but I am NOT familiar with this machine at all. Considering buying to fix and use. Any opinions out there?

I bought a 2146 and the model number plate is supposed to be under the seat but mine is not there. Anyonehave any ideas on how I can determine exact model number on this thing?

Hi all. I have a couple of questions that I hope can get answered here 1. What does the VTS on this model stand for? 2. DSL? Same question. 3. I need one rear tire for it and noticed the NHS letters on the tire after the tire size. Anyone know what the letters stand for? Thats it for now, thanks.

Need two rear tires size 18-9.5-8. Used or new

I recently bought a used craftsman LT1000 riding mower with a B&S 17.5 horsepower engine. I cleaned carb,replaced the two o rings and the gasket to the intake. It surges when running and I have tried to adjust the air/fuel screw with no change in engine. Any one have any ideas on what to do...

[SIZE=3] I have a HR215 SX. When I pull the throttle back it didnt seem to slow the engine down much. It was running fine though and had been since I had cleaned the carb really well about 2 months ago. Before I cleaned the carb it would surge if not under a load. Anyway I was mowing this...

My HR215 was surging when it was not under a load. When I engaged the blades it quit surging. So I took carb apart and removed the jets in carb and the needle valve on the front of carb. I replaced all and now it is missing when running. It can be hard to start now also. Any ideas how to fix...

Anyone have a good picture for reassembly purposes. I replaced my transmission and I am now putting rear wheels back on. I have a couple of decent pictures but I would like more detail so that I can tell exactly which washers go where? Thanks for any help.

Its getting no spark. It had a lot of rust on fly wheel and armature. I have sanded and cleaned both. reinstalled armature with proper gap. still no spark. My next move is to order armature for it but can not find part because of age. Any ideas or maybe a part number that I can order with...

Self propel drive will not pull mower when in 2nd or 3rd. It will pull its self in first. When lifted of the ground the wheels will spin when in 2nd or 3rd but they stop when I put it down on the ground. I tried adjusting the cable once and it worked for a few months now its back to doing the...

When trying to start every now and then I get a kickback when pulling to start and a clunk noise. Associated with this sometimes is black soot out of exhaust. I cleaned the carb, plug replaced, and checked for spark. Spark seems to be fine and its getting fuel. Tried starting fluid and it seems...

I have a JS26 that I can't get to run. I have cleaned carb but still nothing. I. Checked for spark and it has spark but seems to me that the spark is weak. Is this possible, and if it is what might be causing an weak spark?

I have a HRR216K3VXA. My problem is that I can not get the blades to disengage. I disassembled the clutch and put it back on and for a moment the blades were still, then they engaged on there own. This govenor on this mower needs to be adjusted also. It is running way to fast when I start it and...