Search results

greasing all the Zerks seemed to get it to settle down. I guess I got the spindles to spin a little easier and lowered the inertia.

John Deere Multi-Purpose HD Lithium Complex Grease Grease-Gard™ Premium Plus Is there anything special about this grease? Can I use any grease? I have marine grease, can I use that? and do I use one of the other or do they each have a different purpose?

Dropped the deck again today. double checked it was the right belt, hand spun all of the pulleys. watched videos. everything seems like it operates correctly. I did see a video of the one handed mower guy starting a similar one and his did give a good shake before the blades engaged. I'm...

I changed the broken belt on a JD X330. I don't think it matters, but the old blades were chipped, broken and they were dullest blades I have ever seen. (not my mower, helping a friend). The old blades and belt were original and lasted 3 years. In the past when the blades were engaged there...

Hard to tell on the video, but I am cutting on a slope so big that I tried to sit on the fender to keep from sliding off the seat. When I did that the seat safety started to shut the engine off, so I sat on the seat and the mower backfired. She is an oil burner, so before the cut I added oil...

I have turned my push mowers on their side to get oil out and this never happens. This mower was fine after.

So I bought a new needle and float and installed them. I have not tested them to see if they are functioning property. I did cut grass when the needle tip was broken off, so I assume the needle was not working at all at that time. The mower ran properly and I shut off the fuel as soon as I...

I don't have a pump like that, but I blew on it with my mouth and it seemed ok!

I've been using the fuel shut off every time I put it away. I would then run it out of gas. The next start up I would use starter fluid to start it so it didn't have to crank for 30 seconds before the fuel entered the mix. I got ambitious and thought I could fix the flooding issue for $20...

I took the carb off when I first got the engine. I cleaned it up best I could and mangled the main jet when I couldn't get it out.

My needle was bad, currently there is no tip on it. I ordered a new one. I hear the solenoid click. I put in a fuel shutoff and I have been using that for the past 2 seasons. I was hoping to not have to go through the process of shutting off the fuel, letting it run out of gas and having a...

Ok, so a new needle, I probably need a bowel gasket, a new float wouldn't hurt and I can probably skip the seat for now? What Bowl gasket do I need?

I took the bowl off and this is what I found. The needle tip was breaking off and before I put it back together it broke off. It looks exactly like the needle that was suggested right?

I think this is the answer. removing and replacing the seat seems do-able.

From Rotary: Good morning, I was able to look into your Model number 31C707-0154-E. I was able to find the OEM number off the carburetor you needed. However we did not cross it back to anything we will have here at Rotary at this time. I will list the OEM numbers I have found as I hope it will...

yea, you sold me on quality aftermarket, if I can find one!

thanks, I just emailed Stens with all of the information that I have. hope they reply in a day or two. I will keep looking online also.

Holy smokes this complicated. I'm not sure how to search to find a carb that fits. Walbro LMT carburetor brought no returns searching in those sights. I'm going to drink a couple beers and try again in a few.

Nice thanks for this info. I am having trouble figuring out what Carb I need. The carb was on the used engine when I bought the engine and its still on there. I have been told that it is a Walbro Carb based on the LTM 4993 stamped on it. I have found a LTM 5-4993 carb. I believe my engine...

I don't know, maybe someone before me bought a cheap Chinese Carb and has a story to go along with it, maybe it worked out good for them or bad for them. Or maybe someone who knows a lot about these engines will suggest I just rebuild the current carb and offer suggestions on exactly what I...

At the end of the day its a lawnmower. Its not like its going to strand my wife on the beltway! Worse case scenario I have to cut the yard with a push mower one time and I put the old one back on.

A couple years ago, I got a free mower with a blown engine. I bought a $150 used engine and I have been running it for the 3rd seasons now. It burns or leaks oil and if I don't use the fuel shout off when I put it away it leaks gas into the oil. I recently with your help figured out which...

even a $15 Chinese carb?

will the nikki and Walbro have that clip or just the ruixing?

how do you read this date?

what's the part that's not the needle?

Walbro and Nikki are companies that make carbs or they are types of carbs? can I replace a carb with one that doesn't have a solenoid ?

I have to say that I half assed it. I couldn't get to the nut in the back that holds the engine cover on, so I gave up. i did pry the cover up and spray degreaser behind it.

It's spellchecking now. you can right click and turn it on.

I took the rocker cover off cleaned it up and put it back on. The bolt in the lower right position in the photo was not as tight as the other ones. Hopefully that fixed the leak. I'm very impressed with the foam spray engine degreaser from Walmart. Only took about 10 minutes to clean the...

So Im thinking a leak at the valve cover? I guess I clean the engine up, run it once and see where the new oil is? it does not leak when it is sitting.

How do I figure out where this oil leak is comming from? I assume all of that dust is stuck to oil that has leaked from the engine?

cant find it by searching online

I think I got it Model 31C707 Type 54E1 Code 040320ZE

I need help identifying a B&S engine. I am looking for parts especially a carb but want other information as well. If I know the model number all this info would be just a google search away. Here is what I got. Mostly I want to buy a replacement carb.

OHV Single

I bought a used engine, ithe stamp on the valve cover is rusted over, but it is an I/C 17.5 HP B and S. It does not have an oil filter. I searched I/C 17.5 and the internet said 48 oz oil capacity.

So My led screen said CNG OIL. It did it for the whole hour right after I hit 550 hours. There is no intelligence in that right? It probably displays that every 50 hours? It wasent because the engine go hot or somehow it knew my oil was old? and there is no way to reset it like a car? also 48...

Liquid Electrical Tape worked. 2 starts without issue. I kept the old battery also.

My battery bolts and terminals get corroded and then my mower won't start. If I clean then off it starts right up. below is a picture of the brass battery bolts I bought 2 weeks ago. What is making them so corroded? full disclosure, when I bought the battery 2 seasons ago I left the mower on...

So I go to start the Mower today and I just get clicks. I put a battery maintainer on the battery while it is still hooked up and it starts right up. I see that the battery I got at the end of the season, 2 seasons ago is only 160CCA. I can't find my manual, but a manual online says the min...

What am I shooting for in pull string size? Can I just use paracord I have lying around? B&S 6.5hp

It started after I cleaned the battery cables. They didnt seem that corroded, I didnt think that was the issue, but I guess it was. I switched to brass nuts and bolts to hold them on also.

I went tot start the riding lawn mower today and I just got a click when I turned the key. The battery was inside on a maintainer all winter. The battery tested at 13v. The positive cable that hooks to the battery was corroded. I cleaned off the corrosion. If it does not start this time I...

Thank you I got a not so related follow up question. the battery in my mower sat for a month and wouldn't start the mower. I have a boat battery on a maintainer so I brought that battery to the mower and started it. I then put the original battery back in the mower while the mower was running...

At the beginning of this season, I couldn't find bolts that hold the cables to the battery posts, so I used random bolts and nuts that I found. At the end of this season one of the nuts looked burned and that battery post was darker then the other one. Does it matter what kind of metal the...

Hoping to find the correct needle and seat from this. Not enough info here?