Search results

i have a jd x580 and an was wondering if any of you have had to adjust mower deck side-side. I need to and have the deck in the postion that is suppose to be in to adjust What my problem is the gauge is app. 5/8 of inch to tall to fit under lip of deck Wondering why deck is so low. Has anyone...

Does anyone know where I can find a hydraulic valve for my c-141, the part # I have for valve is 106680,k and part # for overhaul kit is 110976 which you cannot find anymore. Does anybody know where I can find them. also need hydraulic hoses part# 106421,need-1, 106420, -need-1, 106651-need 2...

Does anyone know where I can find a good motor shaft for Sundstrand hydro off of wheel horse The following is on tag attached to hydro. 90-1173-LH ,, 04-UL , 23176, 3102902-02. If you know of a place please let me know. THANKS:frown::anyone:

On a sunstrand hydro is their suppose to be shims in the top right shallow hole which I believe is the implement lift. Wht I am asking is when I dismantled mine did not see any shims, what I have read is that their should be Is this correct? if so where or how thick is shims? THANKs:confused2:

Does anyone have or know where I can find a couple of check valve plugs for a sunstrand, I have found new ones for $50.00 ea Don't want to pay that much for them. The slots are ruined in the top of plug for a screwdriver, Has anyone tried to repair with J B Weld, and if so did it do ok? Please...

Do any one know where I can following parts NEEDLE BEARINGS part# 83-3770, SEAL RETAINER WITH o RING part# 83-3800 and CENTER PILOT part# 83-3780 these are for Sundstrand hydro. (90series) off of wheel horse. I have looked at a lot of places but can't find THANKS in advance for help:confused2:

Can anyone tell me where to find the following parts :83-3800-Seal retainer with o ring, 83-3770--Needle Bearings. I have looked at a lot of sites but not have found them, These are for a rebuild of Sundstrand hydo. off of WH tractor. These # is from tag off of housing90-1173-LH,04-UL, 23176...

I have a 4H.P. briggs on a sears high pressure washer and can't get it started. Here is what I have done to it.1. honed cylineder & installed new rings 2. lapped valves in and made sure tappet clearance was ok. Have spark and fuel is getting to cylinder. Checked clearance on air gap and it is...

I have a 4H.P. Craftsman High Pressure Washer, and I would like to find out what engine is on it. The Model # is 10A902,TYPE 023301, and CODE is 97052954. I think it is a briggs but not sure. Would app./if someone could tell me for sure.THANKS:smile:

I have a 14HP KOHLER ENGINE on wheelhorse tractor which has been running fine till today, while mowing it starts to miss and sputter, Did not do all of time, some of the time it ran fine, After done mowing checked points-ok, also pulled spark plug and found it had carbon build up, could this be...

Have a mtd Lawn Mower with a htdro-gear trans. The question is how to check the bypass plate for proper operation while it is tore down. The problem is that it was just creeping along before tear down. Also could it have a lot of air in it? and if so how do you get brid of it? If anyone can help...

I have a hydro-gear :confused2: tore apart to check. Tractor was creeping along, we wanted to check plate in hydro, to see if it was ok. How do you know if is working ok? Thanks for help

:confused2: I have an older wheel horse tractor with a 14 H.P.Kohler engine, model k-321. The valve cover gasket has started leaking oil around it. My question is their a certain torque that you tighten up bolt that holds valve cover and gasket? also when you replace gasket with new one, do you...

:confused2: Is their a way to check oil in Hydrostatic transmission on a power craft lawn mower.Made by montgomery ward. Also i cannot adjust hydrostatic neutral control as book says. Suppose to raise and block up rear end of tractor, then loosen a couple of nuts, start engine and run at full...