Search results

Results 1 to 50 of 500
  1. sgkent

    Blade removal

    use a block of wood to lock up the blade from turning. I wedge it against a bolt or bump out or lay the mower on its side and step on the board to hold it. Torque values are normally a range. Use the lower range if you cleaned and oiled the bolt, or the higher if it is dry. Most manufacturers...
  2. sgkent

    Honda won't start without starting fluid

    probably the choke or primer is not working right would be my guess. Or old gas.
  3. sgkent

    Westinghouse pressure washer

    needing a plug already? Usually they last a long time on a pressure washer unless they are out in the rain and snow.
  4. sgkent

    Blade baffles on walker deck

    need to clean it up. Putty knife, hand wire brush, pressure washer to see what the condition actually is.
  5. sgkent

    How do these cylinder walls look to you?

    hone and new rings. Too expensive to go oversize and bore. Look everything over and measure it before proceeding as other things can be worn out too.
  6. sgkent

    This site is slower than watching my grass grow.....

    it is awful. Locks up, won't post, have to leave and come back in. I try to avoid the place because the site is so messed up. I am sure they know it. Wait until California enacts the new bill that requires all social media sites to pay taxes per use.
  7. sgkent

    Blade baffles on walker deck

    I did a quick google and something came up about a mulching baffle kit. Then there is the photo below from Walker for a C52R deck, which those look welded on. Without photos from you the question is pretty neblous because they use that 52R number loosely. Use a clipping too to resize your...
  8. sgkent

    Clogging bagger

    not a riding mower guy but if the original blades worked well, I would have used originals or tried to match them as close as possible. Other than health and aging issues that we all face, a good portion of my problems these days come from new things that work worse than the old ones I am replacing.
  9. sgkent

    Nagging Question About Tire Pressure

    I would have thought there would be some minor increase because the tire volume should be reduced. A Google AI of the question answers that there is a subtle increase that is barely measurable with most non-scientific gauges.
  10. sgkent

    Intek 12.5HP cranking but not starting fuel coming out exhaust manifold gasket t

    again, fuel should never drip from the bottom of the carb's bowl. It means that the needle is not sealing, or if one has the two piece float area, that many section gasket may be bad. If the engine is so rich that fuel is dripping off it, it will not start. Drain the oil, rebuild the carb and...
  11. sgkent

    Intek 12.5HP cranking but not starting fuel coming out exhaust manifold gasket t

    fuel should never drip out of the bowl even if you crank for hours unless there is something wrong with the seat, needle or it is the kind of carb that has gaskets between sections that help contain the fuel and they went bad.
  12. sgkent

    Annual Tuneup and Intermittent Stopping issue

    please update us. When I come across a situation like that I loosen the fuel tank cap and see it that changes anything.
  13. sgkent

    Honda HRX217TDA Spring on Discharge Chute

    have a toro or I would check. They use one spring in the center, about $20 instead of $120 for a pair. While you have new ones I would visit the hardware store and try to find a couple $3 springs that could be modified next time it happens.
  14. sgkent

    Cub Cadet LTX1045 will not turn over

    was the fuel left on and the cylinder filled with fuel thus hydrolocking
  15. sgkent

    No spark on B&S push mower?

    I do not know specific resistance on a mower but resistance type ignition systems in general are around 4,000 to 10,000 ohms for their ENTIRE length including the resistance wire and plug. 19K sounds like a bad plug. That said, as plugs run the electrode can glaze so it can be hard to get a good...
  16. sgkent

    Toro model 20331 6.75 Briggs no choke/no prime cold start issue

    Always is good to hear someone solved their issue. Thanks for sharing.
  17. sgkent

    Sears 917370431 self-propelled lawn mower hard to pull start rope

    when I start all my equipment, I pull the rope slowly until it is either all the way out, or I feel a lot of resistance. It will pull easily then suddenly sort of hit a hard spot. I then let the rope back in and pull it. The hard spot is basically the engine telling you, "hey, I am ready to fire...
  18. sgkent

    Server problems.

    it is still an ongoing problem. Some browsers do it worse than others. Occasionally code will come up instead of a page. Maybe that is why Google is laying off now - paying people to make others go in circles. DOGE is not at fault here. If anything just the opposite. X, Starlink, Tesla, and...
  19. sgkent

    16 Vanguard no start

    The alcohol in modern fuels is hygroscopic - meaning it pulls moisture from the air. We only use non-ethanol fuel for our garden gear because I got tired of problems from it. And if I won't be using something for half a year or so, I drain the carb and tank, and swab it out if possible.
  20. sgkent

    16 Vanguard no start

    well, your last statement is that it is a fuel problem. How old is your fuel?
  21. sgkent

    Here a spark plug, there a sparkplug...

    The timing and the spark voltage are affected by the plug gap, not how beefy the coil is. The electrons do not care what conductor is carrying them, other than some plugs and wires, rotors etc., that have resistors built into them to limit ignition current. The timing change by changing the gap...
  22. sgkent

    A Repair Manual for My Engine

    what kind a manual. Owner's? Service? Parts?
  23. sgkent

    Carburetor problem

    Drained the tank and used all new fuel? Use Berryman's B12 carb and choke cleaner as a starter fluid or gasoline in a squirt bottle. Do not use Ether or it may blow the head gasket or worse. When I pull up that engine it shows an autochoke and primer bulb. Did you check the auto choke to be...
  24. sgkent

    Toro model 20331 6.75 Briggs no choke/no prime cold start issue

    according to the Toro website, it is a Briggs and Stratton engine 124T02-0203-B1 with an auto choke. Is so, my GUESS would be a something in that area. But who knows, it also shows a primer bulb type base so sometimes those warp. Or maybe the valves are tight and need adjustment. Easiest test...
  25. sgkent

    Toro model 20331 6.75 Briggs no choke/no prime cold start issue

    The 20331 is a generic number. There is a 20331 and a 20331 C. There are three versions of a 20331 C. There are five versions of a 20331. If I go to the Toro site and put in 20331 to see what you have, I will first have to guess at your serial number, and next guess at which engine you have...
  26. sgkent

    Mower smokes/burns like crazy

    you have to figure out why the pulleys are not moving. The smoke is the belt slipping. Could be a pulley rusted solid. Could be a branch stuck in it, a rat built a nest in there, a spring broke, or oil dripped down on the belt, lots of things.
  27. sgkent

    Oil Filter Wrench Size

    take the filter with you to your local flaps and match up a wrench if you want to use that style wrench.
  28. sgkent

    Buying a Still Crated 2023 Model

    for the record, make 1000% sure that the warranty will not be affected. Many times I have bought something one or two years old new and the manufacturer refused to honor the warranty because of the manufacturing date. New to you does not mean new to the manufacturer unless they expressly say it...
  29. sgkent

    Used parts??

    do a google search for lawnmower salvage yard . Or mower salvage yard. There are bunch in the country that sell that stuff used.
  30. sgkent

    crack in crankcase

    I count six threads on this LT1040. What's up with that?
  31. sgkent

    Problems loading pages/posts

    stop by as you pass Europa to say hi to my cousin.
  32. sgkent

    Server problems.

    I tried three or four times today to visit and it always just spins. Not worth my time coming - I hope the moderators see this and fix whatever is causing the problems.
  33. sgkent

    Bent Chassis?

    put it on a flat surface and start taking measurements to see where the differences are. That will tell you what to do next. Frame could be straight but a subframe, mount etc., could be broken. There are some model mowers that have two or three piece frames, and some of those subunits break or...
  34. sgkent

    B&S Replacement Fuel tank

    i might go to amazon and google mower fuel tank, then compare designs.
  35. sgkent

    Agra-fab aerator parts

    oilite may pick up dirt and cause shaft wear. Just a guess.
  36. sgkent

    Info for replacement engine

    Questions you need answers to before you choose a substitute Horizontal or vertical engine diameter of the crankshaft Length of the crankshaft flange pattern (should be the same) tapered or straight shaft Where are the controls and exhaust mounted to be sure they clear the device the new motor...
  37. sgkent

    Bent Chassis?

    so maybe the sheet metal is crooked :)
  38. sgkent

    transaxle filter-- Simplicity

    Did anyone go to this link to see the 10 common replacements for that number someone else in another thread looking for one posted? Let us know if they match https://www.oilfilter-crossreference.com/convert/LUBERFINER/LFP8230 LUBERFINER LFP8230: LUBERFINER LFP8230 replacement filters...
  39. sgkent

    Server problems.

    lots of server time outs. I try not to come here because it can be so frustrating
  40. sgkent

    Husqvarna RZ3016 seat safety switch does not work.

    so it never ran, because that is what you are implying? Or it doesn't work sometimes? None of us read minds well.
  41. sgkent

    Agra-fab aerator parts

    McMaster-Carr calls them grommets, and they sell similar for around $5 each. Amazon has the actual agri-fab ones sold by Amazon for $4.96 each and free shipping if you have prime, two day delivery. That is $40 with tax...
  42. sgkent

    champion generator, backfiring

    backfiring thru the carb can also be a plugged exhaust, anti-spark screen etc.. When someone suggested checking the valves, they meant checking the gaps against specifications. I would think a sheared flywheel key would be unusual on a generator since it is rare it would come to such a sudden...
  43. sgkent

    transaxle filter-- Simplicity

    https://diyengineparts.com/View/121184/briggs-and-stratton-filter-oil-194856 So if it were me, following different discussions online about the part, documented above, I would take the old filter and the list from
  44. sgkent

    Where to purchase a new central bolt for a Honda HRR216VKA blades? Links please!

    The model you posted has different variants depending on year. I did look at quite a few of the variants based on your original post. Some came with a hub that the key was cast into it. That hub was superseded to ones that had a slot. Some use the half moon key. I think you need to take photos...
  45. sgkent

    Back-lash on Superior gearbox.

    if it is adjustable you should find shims or some kind of hub with threads that lets you change the lash by changing the ring gear to pinion clearance. If neither the pinion or differential gears have such an arrangement, it won't be adjustable unless the parts book shows different pitch or...
  46. sgkent

    b&s 12.5hp flathead riding lawn mower engine smoking - looking for suggestions

    oil can get into the cylinder to burn thru either bad oil control rings, or valve guides. Oil can also be diluted by a defective fueling system where gasoline dilutes the oil, and allows it to be so thin it passes by the rings. Do make sure that the oil is clean and does not have a lot of...
  47. sgkent

    Backfire is the name of the game

    when did this problem begin?
  48. sgkent

    Super Z stearing-hydro problems

    moisture in oil or over fill can also cause foaming in some systems. If the oil is milky in color or chocolate in color after the foam goes away, it could be a sign of moisture.
Top