Search results

UPDATE! So I took the drive shaft off and no difference, then I took the PTO of and WHAMMMMO she fired right up. I checked the bearing on the PTO and its jammed tight as a drum... won't budge. Thanks to everyone who helped me with this thing.

no i will do that now hang on....no power with key off or on at any level of the switch... I did check for continuity and it is a ground cable apparently

Thank you for your reply the lights already have a dedicated connector and work as they should

no i will do that now hang on....no power with key off or on at any level of the switch... I did check for continuity and it is a ground cable apparently

here it is

I have Cub cadet 1440 with a B&S 294447-0445-01 that I am assembly back together but I have a yellow wire coming from the wire harness that I don't know where it goes! Any ideas?

UPDATE! So I took the drive shaft off and no difference, then I took the PTO of and WHAMMMMO she fired right up. I checked the bearing on the PTO and its jammed tight as a drum... won't budge. Thanks to everyone who helped me with this thing.

So I got a battery from walmart with 650 cranking amps. Is that enough cranking amps?

Wow ok I will try that. Man i screwed this up. So once i have the gap set your saying I hold the nut and tighten the allen screw to secure that setting?

ok Thanks I will try that tomorrow. I hope I am getting it at TDC on the compression stroke correctly.

I can't turn the motor by hand. I used to but now I can't. I am done for the night. Every time I set the clearance with an allen wrench and then tighten it down and I recheck it, it's loose. WTH? I must be doing something wrong.

I am going to reset it now to .004. I removed the plugs and the damn thing turned over like a champ. So I agree it must be the valve clearances. I'll get back to you in a bit.

Ok I have Cub cadet 1440 with a B&S 294447-0445-01. I needed to change the head gaskets on this mower and reset the valve clearance to spec. Now when I turn the key the motor only turns a quarter turn and stops. If I turn the key again it will still only turn a 1/4 turn and stops. I needed a...

Star Tech you are a saint. She runs perfect now. Thank you so much.

ok thanks I will try that in the morning. See what happens..

I have attached photos of the front and the rear of the governor linkage assemble I believe there are two springs with this model . This first picture has two circles. This view is with the governor assembly removed and looking from the inside of the assembly. One in red and One in blue. I...

67518

I replaced the head gaskets on this motor and now I can't figure out the governor spring set up. It runs but the springs are not correct. I can't find a diagram of the spring placements. Could someone post a pic of the setup please... Thanks in advance. Help this is my second post. I have...

Did you ever get this figured out?

Ok i will keep that in mind thanks.

anyone help!

Thanks fred but that doesn't indicate where the springs connect on both ends of the spring.

I replaced the head gaskets on this motor and now I can't figure out the governor spring set up. It runs but the springs are not correct. I can't find a diagram of the spring placements. Could someone post a pic of the setup please... Thanks in advance.

i checked with a magnet and the gear on the starter and my ring gear are not steel

ok i will try that one and let you know... thanks

you are correct sir 294447-0445-01 just checked and I omitted a 4

The gear on the starter seems to be plastic and the gear on the main is aluminum. The starter that I purchased is model number 795121. When I started the mower it made a hell of racket so i don't think its the correct one. ????

The engine model number i gave was the correct model including all digits. The code on the motor is 9301291. The two pictures I included show the old starter and the one that I ordered which is not the correct one either. As you can see from the shafts the old one is longer and has a unique tip.

Thank you. However, that isn't the correct one either. Now you get my dilemma. I have tried and cannot for the life of me find this starter. I do appreciate your effort!

I have a Briggs and Stranton 29447-0445-01 motor on a cub 1440. I need a starter. I've looked all over the internet and can't find it. Anyone have a clue what the part number might be. Thank you.

Thanks that's what it was!

I have a Briggs and stranton 29447-0445-01 motor. I removed the front sump cover to replace the sump gasket and this round spring fell out. I have no idea where it goes. I have looked at the manual and online and can't find it anywhere. I looks like it might go over the end of the crank...

Hmmm cannot seem to find a listing for the head casket

I just got this mower so I don't know its history. I pressure washed everything before i put it back to together. Thank you for your reply perhaps you know which head gasket model number this mower takes?

ok i found the problem and she's running great. I felt the end of the vacuum line and it didn't seem strong enough. So i blew a burst through it and whamo awesome suction now. I am pretty sure I have a blown head casket. Did a leak down test and also confirmed that as well. She runs good...

no sharp bends and it's brand new i changed it 2 days ago.

Thanks again.... This mower has no solenoid on the carb. There is no fuel reaching the fuel filter. I will try blowing some air through the feed line directly towards the tank. I am beginning to think it's an issue with the tank or the fuel filter itself. It a fairly large clear plastic...

Thanks for the feed back! This is a picture of the pump I bought. The hose on the top right is the inlet? The hose on the bottom right is the vacuum? I Downloaded the manual for this motor and it says to check: the "fuel tank vent, fuel pickup screen, in-line filter, shut-off valve, and fuel...

Kohler CV22s I can't get this thing started. I checked the spark and both are good. I changed all of the fuel lines even to the tank. Bought a new vacuum fuel pump and even tried one off another Kohler but I don't know if that one works or not. The new one is a black plastic one. None of...