Search results

Looking to buy a needle and seat or oem carb. For my Honda harmony riding mower. 11 hp.MZAW 6139134 is stamped on the frame. The first 1 is possibly a 0. Also looking for a new seat. Mine has tears.

I have a 2006 Lazer Z with a good running 19 hp. Kawasaki engine. What direct fit larger hp. Engine could I buy that bolts on with the same clutch.

My carb drips gas after shut off even running. It has a shutoff valve and if I leave it on my gas will be all gone in a few days. I’m looking for a new needle and seat and a bowl gasket. It’s a Honda harmony 1011H 11 horsepower. MZAW 6 139134 if that helps. Anyone recommend where I can buy one...

Honda Harmony 1011 H my gas leaks after shutting down. It has a gas shut-off and if I don’t use it fuel will seep at the carburetor. I’m looking to buy a needle and seat and another bowl gasket. MZAW 6 139134. It has a keiHun carburetor. Anyone recommend where I can buy these?

I’ve got a Trail master mini XRX goKart with a 5.5 horsepower engine. It’s not a briggs, perhaps a predator or Honda clone engine. It had a broken axle and a few covers missing. Hasn’t been run in about 2 yrs. The carb. looked awful inside so I bought the correct replacement for it. I’ve cleaned...

Sorry don’t where to post this so I’m asking here. How do you remove the seat in a carburetor to replace with a new needle and seat on my carburetor. This is a 5.5 horsepower motor on my granddaughters goKart. It’s not a Briggs and Stratton but resembles one. Someone told me it might be a...

I am working on grandaughters goKart, it’s 3-4 yrs. old. It has sat up about 2 yrs. with a broken axle. Got it started and to try to accelerate with no load it will labor knock about 3 times and go dead. The carburetor was nice and clean when I examined it and did a cleaning. It sounds like a...

I just received a new clutch for my 2006 ExMark 19 hp. How do you burnish the clutch and do you tighten the bolt that holds the clutch to 46 lbs? Thankyou

2006 19 hp. Kawasaki, it smokes on startup. I think it’s valve guides letting oil seep by. Can I replace valve guides at home or does a shop need to do the work?

2006 ExMark 19 hp Kawasaki. I know it’s old but, I guess the valve guides are worn or does this mower have valve guide seals like the cars I used to work on. It usually smokes upon start up until it clears the combustion chambers of oil leaked by the valve guides, then it smokes no more and...

2006 Lazer Z 48” 19 hp. Koehler engine Mower has been running fine till now, went to turn blades on and blew the 20amp fuse. I replaced the fuse and blew it also. I’ve been thru this with my Scag and determined the pto clutch was shorted. So now have a new pto clutch in route to me. I found one...

I’ve had this now for the third year. It has 60 or 62” deck and 30 horsepower B&S engine.it has served me well. Is this anywhere compareable to the newer mowers from Scag? In my yard with thinner grass it will get you dirty, I suppose this maybe is normal. In my mother in laws with good grass it...

The mower steering wheel is hanging up when completing a turn. Usually I’m turning to the right. That is generally the direction I mow to. It won’t straighten. If I slightly turn back to the right it will then turn back to the straight position. I haven’t had it up on jack stands yet to...

My little rider mower is getting incredibly hard to steer. Seems that the 2 gears do not mesh smoothly under the front of it. The shaft the goes all the way to the top at the steering wheel has some slack allowing the shaft to not fit snugly upward. How can I improve the meshing of the steering...

Guys would like to ask what is wrong with the mower speed seemed as is the belt was slipping. Finally I ordered a new belt and installed it today. Installed it, put mower deck back on and started it up. Initially I would mash reverse pedal and it would start moving in reverse, but push the pedal...

john Deere LT 155 seems to travel fast enough until you go up a little incline. This incline is only 20-25 ft. There is not any belt to control this, Is It? It seems it is all hydraulic controlled. I know this mower is kinda old around 1998-2001 but it doesn't smoke at all, seems to have good...

Hello, I am a new member a will have posts following I'm sure. I am retired 10 months now and like to repair things. I own 4 different brands of mowers right now. Some I like better than others. My exMark is superior to the others with my Honda being next. My Ariens comes in 3rd with John Deere...

I am needing to know the size of string the Stihl fs66 uses. It is a dual line. Also can you buy the gas cap gasket alone or just buy a new gas cap. If I tilt it a little gas drips out of it. Guess I should try a determine if the threads are somewhat damaged. Sometimes a cap will feel tight but...