What has happened to my Kohler ?

Hello Scrapman,

Checking for spark outside of the cylinder is only a "rough guess" that the plug will fire when under compression. I've done that countless times in the past also, but it is where it can trick a person.

The flash bulb spark testers will also trick you because there is no stress placed on the coil. A true spark test is an adjustable spark test adjust out to about 1/4 inch. Even then you have to watch and listen for a strong blue spark with a snap sound. If the spark is orange or inconsistent jumping the air gap, the coil is weak and failing. These same tests have been used on earlier automobiles for years.

I learned much of this working in auto repair shop years ago when I had an early 90's Corvette to check over for a misfire that the other techs could not seem to figure out.

The shop had an old 70's bench top Champion spark plug tester cabinet and the foreman said to use that.

Even though the plugs were new, no one had tried testing them under pressure using that test cabinet. Sure enough, one of the plugs would quit firing when the test cabinet air pressure reached about 40PSI.

When a spark plug is under in-cylinder compression pressure it produces a very high resistance against the spark trying to jump the gap. This is where spark plugs and coils often fail.

To verify if a cylinder is producing power on this V-twin engine while running, simply use a spray bottle to spray the exhaust outlet head pipes. If the water burns off immediately that means power and heat are being produced. If one is slow to burn off the water, that would be the cylinder to look at closer for a cause.

These engines require fuel, air, compression and combustion on each cylinder.
Hello Auto Doc's

And thank you so much for that very informative post. There was so much in there that I didn't know ! But then I am only a mechanically-minded farmer who is well past his retirement age ;) I will report back as soon as I have got all the bits and pieces and put it all back together.
 
UPDATE.

I think I know what has actually happened to my Kohler engine. I mentioned previously that the oil filter appeared to have loosened and was allowing oil to leak out of it. Because the engine air intake is quite close to the oil filter I think that the engine actually sucked in some of the oil from the leaking filter, hence the oil in both the air pre-filter and the main filter and onward into the carburettor and then eventually, after a combustion stroke, into the exhaust system.
This would not be my first guess. Oil in the carb & air cleaner can be caused by a badly clogged air filter or overpressure in the crankcase. The overpressure condition can have numerous causes... blown head gasket, worn out piston rings, faulty breather, or bad valve seals and guides. How many hours are on this engine? I'd definitely do a compression check. Given that it will start and run for a few seconds, I'd suspect a head gasket that seals enough when cold to start, but as soon as it heats up, compression is lost. This is just a guess. I have a mower with a Kohler Confidant engine, which is similar to the Command Pro. Kohlers tend to have a few more head gasket problems than the others, based on the number of Kohler head gasket videos I find. On the Confidant, the head gasket changed a few years ago to a much more robust design. I only know this because I replaced mine.

BTW, a couple of seasons ago, I had an oil filter that loosened up on me, and leaked oil all over the engine bay. Luckily it was a slow leak that started late in the season, and didn't result in oil starvation. None of that oil got into the air cleaner. Before every mowing, I suggest checking the oil level, and verifying that the oil filter is tight.
 
I always check my oil before starting to mow. I see way too many come in with low oil and loose filters as well not to. l
 
This would not be my first guess. Oil in the carb & air cleaner can be caused by a badly clogged air filter or overpressure in the crankcase. The overpressure condition can have numerous causes... blown head gasket, worn out piston rings, faulty breather, or bad valve seals and guides. How many hours are on this engine? I'd definitely do a compression check. Given that it will start and run for a few seconds, I'd suspect a head gasket that seals enough when cold to start, but as soon as it heats up, compression is lost. This is just a guess. I have a mower with a Kohler Confidant engine, which is similar to the Command Pro. Kohlers tend to have a few more head gasket problems than the others, based on the number of Kohler head gasket videos I find. On the Confidant, the head gasket changed a few years ago to a much more robust design. I only know this because I replaced mine.

BTW, a couple of seasons ago, I had an oil filter that loosened up on me, and leaked oil all over the engine bay. Luckily it was a slow leak that started late in the season, and didn't result in oil starvation. None of that oil got into the air cleaner. Before every mowing, I suggest checking the oil level, and verifying that the oil filter is tight.
Thank you @GearHead36 for that much appreciated detailed post. I always check the oil level on every engine before I start them (with the exception of our car and pickup) That was drilled into me about 65 years ago ;) I do intend to check the tightness of the oil filter in future on any engine where the filter just screws on as opposed to those that are inside a filter housing that is bolted on.
 
I always check my oil before starting to mow. I see way too many come in with low oil and loose filters as well not to. l
Thank you @hlw49 And you are so right about that. If it's got a dipstick and is easily accessible then pull it out, wipe it clean, put it back in the engine again, pull it out again and check the oil level and then put it back in again. What annoys me is when some of these manufacturers make ridiculously long dipsticks that can be difficult to remove and even more so to put back in.
 
I suspect soon that engineers will do away with traditional dip sticks and have owners rely solely on an electronic oil level sensor. Great! more electronics to fail at a higher cost to manufacture.
 
Back
Top