Briggs starter issues grind and locking

Briggs Intek 31P7770348 E1 04052QZA. Picked up a nice mower For 300 a couple years ago. Now I have a starter issue. The starter wouldn't always catch and just grind. then It wouldn't even engage. Checked it out and found the bendix was totally destroyed. Went to the grave yard and got a good starter and all worked good for a day. What I found is It either grids or locks at one spot on the fly wheel. The fly wheel is part #591760. I think the teeth are worn on the fly wheel. It always happens at the same spot on the fly wheel. The teeth either don't mesh and grind or the teeth lock up edge to edge. The picture here is showing the gears in a locked situation. I have 2 junk engines.
3197770377E1 with a flywheel part number 591758 And 31f7070112E1 with fly wheel 693556 My flywheel is 591760. Can I use one of the two flywheels to replace my 591760? Please advise. Thanks , Matt.
Im not sure of the situation but the starter gear on my old Harley would behave the same as you describe. Im believing the issue was a worn bushing that the starter gear shaft spinned in - causing slop and bind. Was my situation.
 
congrats on getting it running. Keep an eye on the mesh and make sure no further damage occurs.
 
Briggs Intek 31P7770348 E1 04052QZA. Picked up a nice mower For 300 a couple years ago. Now I have a starter issue. The starter wouldn't always catch and just grind. then It wouldn't even engage. Checked it out and found the bendix was totally destroyed. Went to the grave yard and got a good starter and all worked good for a day. What I found is It either grids or locks at one spot on the fly wheel. The fly wheel is part #591760. I think the teeth are worn on the fly wheel. It always happens at the same spot on the fly wheel. The teeth either don't mesh and grind or the teeth lock up edge to edge. The picture here is showing the gears in a locked situation. I have 2 junk engines.
3197770377E1 with a flywheel part number 591758 And 31f7070112E1 with fly wheel 693556 My flywheel is 591760. Can I use one of the two flywheels to replace my 591760? Please advise. Thanks , Matt.
 
From the photos it appears that the Starter Gear should be Closer to the Flywheel. Incorrect Starter?
Teeth should fully engage Flywheel. Is this an old post? Site was hacked a couple days ago.
 
Is the engine hard to turn over when starting? Does the starter sometimes fail to turn the engine and stop at the same point? If the starter is not always turning the engine over, i.e. the engine compression seems too high, it could be a valve adjustment problem. Adjusting the exhaust valve or valves, to the precise proper adjustment will allow the exhaust valve to open slightly to reduce the compressor during low sped cranking. If the gap is too much the exhaust vales remains closed and the compression remains too great for the starter to turn it over. If there is something wrong with the flywheel ring gear, yo
Lot going on here that the OP will have to address. re date code on his engine - 04052QZA - the date code if goofy unless the Q is a 0 in which case the manufacture date would be May 20, 2004. If so the way I read the Briggs fiche, the flywheel part number should be 595100 because it was made prior to July 2012. Someone can verify that but it is how I read it. (I think the OP updated the part number later in the thread to the same.) The casting number on the part itself is not always the Briggs part number. Probably used from a salvage yard or Ebay is all that will be available if one of the others doesn't fit. As to whether the ones off the alternate engines there will fit, that depends on the date codes of those engines which were not provided. Have to go to the fiche for those engines and look up the flywheel PART number. The casting number on the flywheel can fool.

yes. It just isn't getting a good mesh. Pretty rusty too. Bendix might be compromised but the distance between gears is also not right.

View attachment 74971
Also - the gear is all the way up in the photo. Doesn't the gear drop back when it is not spinning on this model starter? The photo below also shows a gap on the opposite side of the armature shaft - As if there is a lot of play in the gear and shaft. To me, it looks like the starter needs work or replacement. It's possible it simply stayed engaged and wore the flywheel out. Lack of maintenance is the culprit here me thinks.

View attachment 74972
the ring gear doesn't look all that worn, you should be able to see the damage. The starter shaft does show wear that shows the starter drive being pushed away from the ring gear. The starter drive gear is also showing wear.
 
Back
Top