craftsman

Does anyone know where I can get a good used #532161592 pulley. It is no longer manufactured and I have looked everywhere on the web. Also, is there an off the shelf replacement that could work as a substitute? It would seem that out of all of the pulleys in the world that there would be...

I have a hose that goes from the engine back to the back around the fuel tank somewhere. Any ideas?

My leaf blower will only run with the choke closed a little bit. Also when it runs a small amount of oil comes out off the breather tube.

Craftsman Model 917 270820 tractor with B&S 42E707 2631 E1 Engine Surging when idling - I can see the governor moving back and forth, but it will not idle smoothly - I can see the governor springs in there and it seems to not have any missing parts (like it threw a spring off), and all the...

Forgive me if this has been addressed before. All the posts are starting to look alike to me. My +/- 2016 mower turned over twice last Saturday and then failed to turn over at all. Now, no clicks from the solenoid. Headlights don't go on with the key in 'on' position with a battery delivering...

Worked fine last year at this time. Replaced the spark plug, drained all fuel and put in fresh non-ethanol fuel and it just won't start. It doesn't even try to start. I may as well just disconnect the spark plug because I'd get the same response to pulling on the rope. And ideas on what to...

You guys know this common one? One pacman screw on the inside one on the outside. I can get it started but doesn't stay running unless I throttle it which only lasts for so long I've put a lot of car cleaner through this though maybe it's that diaphragm in there too brittle as I recall causing...

What is the part number of the valve guide bushing? I need a new one.

Long time listener, first time caller - watched every video I could find on YT and read through every post here and on Reddit and am looking for some help! Craftsman T1200 Model: 247.203726 DOM: 02/2018 Purchased used from a gentleman that fixes small engines, said it was in perfect condition...

Model 247.288812 > the lights are supposed come ON when the tractor's engine is running & turn OFF when the ignition key is moved to the STOP position. Mine don't turn on. The fuse & blubs are good. Looking for recommendations. Thanks.

Hello. My edger, won't start. The edger is a Craftsman 247.772460. The engine is a Briggs and Stratton 550 series, serial number 11 0204 54 57251. It will start when you prime it but will not stay running. Spark plug was replaced. I took the carburetor off and cleaned it and that did not help so...

I replaced the carburetor . It started right up and began smoking blue smoke. What can I do?

So here It goes, I bought a Craftsman DGT6000 (1998) with the 27 HP Kohler Command Pro V-Twin a month ago knowing It had some Issues. It started and drove when I went to look at It and the engine sounded good so I bought It. Got It home and started messing with It and found It burned oil bad...

This edger is a 4 cycle machine. I cannot get it to start unless I use starting fluid. It will fire up immediately. I disassembled the carburetor and found nothing wrong. Finally gave up after many tries and bought another carburetor. Same problem. Won't start unless using starting fluid...

Hi. I can't figure out what magneto I need for my craftsman yts3000 ride on mower. Model 917.289140 21hp briggs platinum xrd engine #143.008501 I believe it's made by Tecumseh but there are no labels saying so. The research I've done trying to find the correct part and part number has only led...

Have a Craftsman 22" model 917.376570 Need one rear wheel for it. Are there other brands other than Craftsman that uses the same wheel? P/N for wheel 194387X427 Thanks

Hi, Was gifted this older Pressure Washer and looking to rebuild the Pump. No name on Pump, it is a 4 Screw model and looks like a Kurcher Brand but no label or markings. The Pump for this model # at EReplacement parts is not the same pump??? They want $350 for a new pump. Will try to...

Hey guys, I picked up a Craftsman Pro series T7400 and the previous owner had re-welded the deck mounting brackets. The paint he used in no way matched the color of the deck but whatever. I bought some rust-oleum golden sunset (gloss) from ace hardware but it’s way too light yellow compared to...

I've got an older apx. 2000' 20hp I believe, LT2000 Craftsman rider. I'm told the transmission is shot. Can the transmission be replaced with another craftsman transmission, say from a LT1000, Are parts like that interchangeable? Thanks guys

DOM is 2020 and it has been fine until this season. Engine power seems ok. I just stop moving in those gears after 30-40 minutes. These are the gears I use the most while cutting. I can put it in any other gear and keep going (1,2,5,6). My front yard has a ditch and a slight incline...

Hello all I hope someone can help me on this. Ok here is my issue i am rebuilding this as it was a parts machine new motor clutch spindles and belts. I'm up to when I pull my arms is the engine shuts down. I replaced the handlebar switches bypassed the seat switch for testing also if I pull the...

First post here, I joined because I can't figure out how to install a spring that holds the side door shut - the door that covers the ejection port, if that's what you call it. Couple of days ago I bought a new side door (it's on my avatar, solid black) and I had a hard time getting the old one...

i have accumulated a certain amount of wiring knowhow over the years on tractors and lawnmowers... one question, my 15.5hp Briggs has TWO harnesses coming out by starter. one w/red/blk ... the other (not sure of wire color) i get that one black wire is more than likely the kill wire, and the...

I have a Craftsman DGS 6500 riding mower. I was mowing along just fine when it suddenly stopped. It clicks when I turn the key but won't start. It won't even turn the engine. I did a quick test bypassing the starter solenoid by touching the 2 posts on the starter solenoid and it turned the...

Craftsman Riding mower runs for 2-3 seconds and then dies

How do I raise deck height in front 2". Ofcourse the trun knob doesn't work well but it fails to move front height. What do I do to raise front height permanently?

Hi, Does anyone know how to remove a stuck air cleaner cover when the retainers just spin? I tried lifting with vise grips while turning counterclockwise, but nothing engages. It will help me a lot if anyone has pictures of what I'm dealing with under the cover. Thanks in advance, Dennis

I have a craftsman lawnmower pgt9000 for many years now, which started blowing fuses after running for few minutes. Have replaced a bunch of fuses in past few weeks. Any idea on what could be wrong? I replaced the belt which was about to worn out before this started happening. When checking...

I am rebuilding this 74092 and was wondering in relationship to the run/stop function, does it stop when the circuit is maintained or broken? The switch is good, wiring has good continuity and spark remains regardless of switch position. This is odd, so reaching out to maintain sanity….

Hello everyone Have the craftsman’s 917.272011 riding mower. Runs like a champ. Clutch stop spending and was bound up. Ordered a new one online. Installed and still not working. I have done the following. Test the wire with the pull switch for continuity and also voltage. When pulling the knob...

I am thinking it’s compression release but i tried the little trick of covering the intake so it starts up but it didn’t work. What else could it be. the starter is new and battery is too. adjusted valves too.

On my 2014 Craftsman YT3000 model 917-288525, is there any way to check the oil in the hydrostat rear axle? My mower starts okay then after about 30 ft it starts to make a whining noise 50 ft or so further on it stops moving and wont drive at all, if I let it sit for 30 minutes or so it will...

Craftsman 917.289272 (YT4000 ??) MFG in 2010. Upgraded front wheel bushings using bearing kit upgrade and added washer bearing also. But now steering control over front wheels has a problem where both front tires direction will suddenly turn just a bit left or right requiring constant steering...

Unable to source replacement brake disc, part # 407134 (Husqvarna part # 583301401). All I can find are listings showing as “Discontinued”. This is a long shot I know but does anyone know of a suitable replacement that matches the OEM part?

Craftsman rider. New ignition switch, battery, wiring harness and spark plugs. Turn the switch to on position and volt dial does not move. What should I look for next?

I have a Craftsman Pro Series 8200 that the electronic PTO was cutting off when mowing the yard. I did a lot of research and replaced the PTO switch, Electronic PTO clutch, initially and still had the same issue. The mower at times seemed to not want to start ( already have new battery) and so...

Greetings, Curious, anyone ever see a Briggs Stratton 26HP Intek just stop with nothing and no noise, no locked engine, just no piston movement, but valves work fine on both heads. One piston at top and the other at bottom. How is it possible for both roda to let go at same time with no lock...

Delete

I'm having to get off my 917.270514 craftsman tractor to put it in a different gear. Is there somewhere to grease or oil that would free it up more?

Hello - Could really use some help as while I like to do a lot of things on my own, wiring & wiring diagrams are NOT my strong suit! I replaced my ignition switch this weekend as I was having some trouble with the tractor turning over unless I was pushing down on the key when attempting to...

Hi, I've done a bit of googling too much almost and also searched this forum and threads either it's not on here which I doubt or I can't get the right key words to pull it up. Can some one tell me how to make this adjustment or tell me what the type or carburetor name is so I can attempt to...

New Reconditioned Peerless Tecumseh 6 speed transaxle. Never installed. Sat in the original shipping box for years. These are used on Craftsman, Ariens, Poulan, Weed Eater and more tractors. Part number 794694R Original Tecumseh Part Replaces OEM Part Numbers: 794602 794602A 794603A 794712...

I,ve had this mower 3 yrs. without a problem. Mowed most my lawn yesterday & went out to finish it this morning. It started right up. As soon as I let up on the brake/clutch it died. If I push the pedal in it starts right up every time. As soon as i start letting up on the pedal it dies. I'm at...

I am looking for a mower deck for a craftsman LT1500 (mod# 247.288820) or a Troy bilt pony (as most part numbers are the same. I scraped a tree and tore one of the mounts through. I don't think it can be welded and frankly I'm tired of nursing this deck season to season. any ideas?

Was mowing lot next door and suddenly the motor just starts racing. I shut it down and it took a while to shut off. I started back up but the motor is still racing at top speed pretty much no matter what position throttle cable is in. Throttle cable seems to be operating properly. It's...

I have a Craftsman YS4500 (917-276691) (Husqvarna YTH22V42) and when I went out to use it this week for the first time this season it did nothing when I turned the key. No solenoid clicking. No starter turning. Nothing. Last year I had notices that the rubber cover seemed to be a little in...

So I have this Craftsman Dust Blocker Bag . On the inside it seems to be padded ? Or is it years of tiny grass clippings that got stuck ?? Real hard to take a picture of this ! Just how do you take the bag off the frame ? Maybe I can empty the tiny clippings !? THANKS !

Craftsman T2400 Kohler engine (24 hrs on the guage) purchased from Lowes May 2022. It has been doing great. Wife can never remember to choke before cranking OR to take it off choke once it is cranked. Yesterday she jumped on the tractor, cranked it up and took off with the choke engaged. I...

I am looking for a wiring diagram for a Craftman 247.203791 riding lawn tractor. It has a 22hp Kohler with a 46" deck. I went on the sears website and nothing. I can get parts diagrams but not wiring diagrams. I tried googling for a shop manual but nothing helpful came up, If i knew the MTD...

All the model numbers are in the pdf. I keep this mower on a Battery Minder when I'm not using it. The first time I ran it this year, it cranked ok and I mowed for about an hour and stopped it to blow the clippings off the deck. Then it wouldn't crank; not even a click from the solenoid. I...