Search results

My neighbor came to me and said he was having a problem with the deck belt coming off the mower. So I helped him remove the deck belt and I noticed that after the belt left the deck it twisted going around the electric clutch pulley but straightened out on the other side. We removed the deck and...

Hi, I recently purchased a 2012 Husqvarna RZ4824F with the Kawasaki FR730V-AS13-R on it. My friend was starting it by jumping the solenoid with a screwdriver. He told me all it needed was a new key switch. I replaced the key switch and nothing. I started checking the wiring harness and noticed...

Hey guys, I have acquired a 2014 Toro Timecutter SS4216. Model #74616, Serial # 314000559. It was not running but it had been as i knew who owned it and it had been setting up for a while. After a little clean up the engine fired up and ran. I remembered when we tried to load it my friend said...

I got a craftsman riding mower made by MTD, model (247.288841). It is supposed to have a 19.5 B&S engine in it but instead it has a 17.5 B&S engine in it. Model (313707 0126 E1). I have found several (rigged) items on this mower and have been able to correct them. While checking everything out I...

I have a 2012 Snapper RZT26520 Zero turn. It has a B&S 26hp (44P777 5167 G5) engine on it. Engine works fine but the PTO seal on bottom of engine went bad and started leaking oil everywhere. I released the belts and removed the center bolt that holds the clutch on. Clutch would not move so i...

Hey guys, have a question. I am interested in this Dxie Chopper Silver Eagle 50" Zero Turn. It came with a 27 hp V-twin engine and its a 2015 model. Well the engine went bad and the owner replaced it with a Kohler 20hp V-Twin engine. Wouldn't this big of hp difference in the 2 engines effect the...

I have an older B&S 18.5 ohv engine that had a couple of issues mainly camshft so while i was in there I decided to replace the rings because of low compression. the cylinder wall and piston were not scared up so i honed the cylinder for a few seconds cleaned everything put new rings in, new...

I have a B&S 26Hp V-Twin (44R677 0016 G1) that I completely rebuilt with new seals and gaskets, soaked and cleaned out all passages. Engine idles and runs at operating speed fine but when I engage the mower deck it starts to backfire some. Any ideas what would cause this? Going to try a higher...

Hi. I have a B&S 18.5 engine (31N707 0301 B1) that will start but backfires real bad. So I took carb off and cleaned it real good then put back on, no change. Adjusted the valves and no change. Cleaned coil contacts, no change. Took Flywheel off and checked the Key. No damage to key. I then took...

I have a B&S engine (10T502-0457-B1) that when I pull it a couples of times it seems ok but then when I go to pull it again it will violently snatch the pull rope back. I checked the flywheel key and it seems to be fine. What else would possibly cause this reaction. Any help would be...

I have a Kohler XT650 149cc Easy Pull engine that is hard to pull and engine wont start. It has good oil level, coil has spark, new plug, carb cleaned. Clean air filter. All the linkage is good. But the engine is hard to pull, the motor turns and there is no scrubbing or scrapping noise coming...

Have a B&S 20 HP engine that the compression release lever broke on. Cleaned everything out and put new camshaft in and everything back in exactly like suppose to be. New plug, new oil. Took carburetor apart and cleaned it all out and everything on it was good. Checked linkage and springs for...

I have these two trimmers and they have no compression. I have searched the major websites for parts and have not found one that lists or sells the rings separately. They all on list the short block assembly to replace them. Does anyone know exactly what size of ring I need or where to get them...

I have a craftsman Platinum 7.25 self propelled lawn mower that runs but it starts acting up after a few minutes of running and I find oil in the air filter case, it seems to be coming from the hose that comes from where the Breather Reed is at. I took off the cover and didn't find any backed up...

Hey guys, have a problem I cant figure out and need help. Have a 21hp OHV (331877) engine that starts up and runs fine but with in a couple of minutes the intake will have a lot of gas in it and you can hear it boiling after you shut the engine off. I replaced the camshaft because of broken...