Search results

ok. i'll order a few today.

123K02 series. does anyone know the size of the woodruff key (crescent shape) for the shaft. there are two slots. they appear to be the same size.

The idler pulley must have been removed and then a smaller belt was used to compensate. I found a idler assembly on Ebay for about $30 which included the arm, spring, pulley, spacer, etc., but the set up I have worked fine without the idler pulley. I don't think its a safety concern. As for...

its the engine belt. someone suggested putting a stretch belt on it since there is no idler/tensioner pulley

my tag on the back of the mower list it as a P21550. technically it is a P21550KW. self propelled 21" 5.5 hp "0" series designation. it is a side discharge mower, but i use the mulch cover.

no this looks like a newer model than mine. I have a self propelled, steel deck model from the mid 90's with the kawasaki Fc150v engine. But I do like the kawasaki engines and you could find them on older john deere push mowers

I have a 5.5 hp kawasaki on my '94 P21550. i replaced the drive belt with a Stens brand (3/8 x 25 3/4). it was too big so I ordered another belt measuring 3/8 x 25.5. These were both supposedly oem replacements for the part number 1-2353 given in the owner's manual. I don't have a tensioner...

Part number on carb is 17053 05

Your right about it not being OEM. I'm trying to clean the OEM carb, but it's been a fiasco. The fuel shut off assembly is packed with a crumbly, white material, and also some jelly like substance

Bought a replacement carb, but there isn't a hole for the throttle linkage to fit in. Should I drill a hole to secure it?

thanks.

tried to up load pics but file was too large. model#39pcm-20-b serial#102922

i'm having a hard time finding the original engine for this mower. the parts manual says the parts # is E243. Not sure what this equates to. The current engine is a predator verticle shaft, but the air filter housing rubs agains the wheel. I'm trying to see if it takes another verticle shaft...

He has a good thing going selling parts and mowers that he gets for almost nothing, but he did mention that his boss/salvage yard owner started to immediately scrap the mowers when he got wind that the employee was making some money on the side. I guess I'll just keep using him as my parts guy...

i was working on a powermore 139cc and was fighting kickback on the recoil starter. I check the flywheel key it appears to be ok. When I got the mower it had way to much oil and thought it might be hydrolocked. I pulled the plug and removed what I could out of the combustion chamber and...

I have a person that sells mowers and parts out of his home. He mentioned that the worked at a salvage yard and that he gets decent mowers all the time. I feel awkward about asking him where he works. Does anyone know of a good salvage yard or recycling center in the Houston area where mowers...

When I engage the self propel on my push mower it feels like its having a hard time going straight. I replaced the front tires already and the drive belt looks ok. Should I replace the front wheel bearings or is this a transmission issue?

I have a 2003 22" electric start mower and I want to remove the key start harness and just put a brake cable. Anyone have a part number

Does the float needle valve rest on a seat(gasket) as in Briggs engines or is there a different design. I didn't notice one when I cleaned my carb. (FC150v-FS11)

as I was cleaning my carb I noticed that there didn't appear to be a seat which the needle would rest on. Does the mikuni carb on the Kawasaki fc150v not have one?

Is there an alternative to the 21171-2200. No aftermarket that I can find. Don't want to pay $100 for a new one. Will one work from a Honda?

I can't find an aftermarket coil for the Kawasaki 21171-2200. Watched a Bruce Pender video on youtube in which he substituted a coil from a Honda GX160. I'm willing to try this as opposed to spending 80-100 on the Kawasaki coil.