Search results

Sorry...991083, ser # is 022198 Yes, that is my video... I can get a better one if needed.

HELP? Someone? Anyone? Do the springs get loose and worn and need replaced?

I am replacing the idler pulleys. On the pulley on the right, if sitting in the seat, how tight should the bolt that goes through the deck that holds the arm on be tightened? How about the bolt holding the pulley to that arm? Should they be TIGHT! or a little loose to allow the arm to move?

I have changed all pulleys and still have this rattle and belt jump. Do I need to tighten the tensioner bolt more? Reason I ask, is I can remove the belt with lots of pressure by removing it around the pulley on the left… it isn’t easy, but can be done! This mower when new, with the blades...

Thought so...thanks!

I bought a new idler pulley for my ZT HD52...when spinning the shaft to check the bearing, it has a spot that you can feel it sort of bump when spinning it. I don't know how to really explain it. Is it a bad bearing? I assume I need to get another pulley?

Belt was installed correctly until it was ran for awhile on uneven pulleys and began shredding. I have flipped the pulley and now everything lines up nice and level...I hope to be able to grab a new belt tomorrow.

Ya'll are awesome! Thank you!

Also, what is the easiest way to release the belt tension? I had a hell of a time with it when I replaced the spindles.

I will try flipping it and see if it helps...

It’s a 991083, ser number begins with 022

I recently changed my spindles and thought it didn't look right but ran it anyway. Now, sure enough, I am shredding my belt. My middle spindle pulley looks to be sitting too high...I thought I had put everything back just like it was. Is that my problem...how can I fix this?

I was thinking the same thing...

That is the new spindle/shaft in the pic...the stepped washer still fits it perfectly.

Thanks!

ok guys, I got my new spindles in and they came with new bolts and washers. All of the washers are flat, but one of the old ones is sort of lipped so part of it fits into the pulley, if that makes any sense...do I reuse this old one? or use the new flat one?

For me it's simply a time issue more than anything...working 12 hours days makes it hard to get to a shop that has the tools needed and will do the work. I'm sure I'd have to leave it with them then pick it up on another day, so that's two days I have to find free time to get to town to get to...

NO do not delete anything! There is some amazing info here! I have tried most everything mentioned and still cannot break things free...my next trip to WalMart, I may try to find the stuff mentioned to break up the rust and separate the metals (don't kill me if that isn't an accurate...

The magnets did stick to the spindle housing...

I don't believe these spindles are aluminum...they are really heavy.

Thanks everyone for all the info! After spending quite some time yesterday, along with lots of heat, lots of penetrant and even more cursing, I was unable to break down the spindle! The piece on the bottom of the spindle at the blade bolt just would not break loose! So, I will be replacing the...

The piece isn't reverse threaded is it?

I got a spindle removed but cannot for the life of me break loose the piece thats screwed into the spindle covering the bearing...I'm using a pipe wrench on each end and a cheater pipe 4 ft long! It moves slightly, just enough to make me think I am accomplishing something, then it stops! I've...

So about 2 inches?

Mind if I ask what size socket I will need so I can pick one up if I don't have it?

I have now...sorry! When I asked, I hadn't yet had time to sit still long enough to watch it. Today, I hope to pull one of the spindles and try my hand at removing the bearings.

Any videos on how to do this? I don't have any experience at all with bearings, much less with drilling holes and adding zerks...

Thanks everyone for the help! Stens is a good reliable brand?

The spindle bearings are easy to change?

My deck is REALLY loud when the blades are engaged and I pretty sure it's the pulley bearings or spindle bearings. I would like to change them all...do all the bearings have bearings? Just trying to formulate a parts list before I get a chance to pull the mower out and look things over.

Where can I find a service manual for my HD52? I searched the Gravely site but only an owners manual popped up...

I am at the 100 hour mark and the dealer is telling me I need to service my hydros, which they can do for $250. What all is involved with this? How difficult?

I have a new echo 266 weedeater. When using it my arms start kind of cramping up and I feel like it isn't long enough for me...kind of like I am all hunched over to use it. Do I just need to adjust the handles on it? It looks like I can slide them towards the engine some.

Mower is a Gravely 52HD I took the mower in for its spring tune up...new blades, oil change, etc. The invoice said they changed all filters, oil, changed blades, leveled deck and checked air pressure in tires. When I took it in it was cutting perfectly. I got it back and the left side was not...

Is the Echo line at Home Depot the same as at the dealers? There is a substantial price difference and want to make sure I am comparing apples to apples.

My old Craftsman weedeater/brush cutter bit the dust last summer so I am needing a new one and looked at Echo the other day. I am needing one I can change the head from the string to a brush cutter blade for use out on the deer lease. I am looking at the SRM 266T...Any opionions on this?

HD52 with 23hp Kawasaki Took it in for oil change, new blades and new air filter...Grand total = $195 ! What the heck?? This sound right? I bet it was all done in less than an hour, probably half hour tops! Guess I need to do this myself every spring from now on, regardless of warranty or not!

Mower has 23hp Kawasaki, just over year old. When engine is cold at startup, get large puff of smoke. It does not do it when engine is warm. Is this normal? Dealer is saying it is!

I have a cyclone rake lawn vacuum that I use during the winter for leaf cleanup...is it ok to tow with these mowers?

What difference does rear wheel size make? Would the 22" tire be better than the 20" tire for any particular reasons?

I have decided on Gravely but am having a hard time deciding between the HD and the Pro Turn, which I think is the next higher level mower. What are the main differences? I only have 1 1/2 acres to mow, but it is far from a highly manicured lawn and I want to make sure I buy something that will...

I have almost decided to pull the trigger on a Gravely ZT 52HD. I was quoted a price which is exactly the same as other dealers I have looked at online. Are they like a car dealership with room to haggle? I never like paying sticker price! :thumbdown: