Search results

Thanks for the google link, I have tried that. This mower housing deck is not available anywhere, hoping someone has a good housing or a lead on one that I have not been able to find.

Looking for a deck housing to replace my current deck. If you have one or a lead please let me know. Thank you

Yes, NGK CMR6H. The first spark plug I have ever had that went bad.

It was the spark plug. I took it out and grounded it and it sparked, but evidently it wasn't enough. Replaced it and it fired up first pull and runs great! Thanks for all the advice.

Thanks for the replies, I'll check the spark arrestor and I am going to change the spark plug, I think I tried a different one last year but honestly cannot remember for sure. If neither one of those fix it then I'll look to take the carb off and try to clean / rebuild it.

I've got a 3 year old pole saw that I can't start. It has progressively gotten harder to start over the years. I put fresh gas in it today and it sputters like it's going to start but it just won't run. I bet the saw doesn't even have 2 hours total run time. Any suggestions as to what to...

Thanks for the replies. One of my tires is actually holding air. I think I’ll try some slime in the one that is leaking down and if that doesn’t work I’ll get some new tires or tire/wheel combos. I’ll just have to measure the axle shaft diameter and hub length.

I'm thinking by the looks of this the only way to adjust tracking is to loosen the stop nut on the linkage rod and turn the large nut to lengthen or shorten the rod- does anyone else know of another way to adjust? Both trans track backwards when in neutral. Any advice appreciated. Thank you

Thanks, the sticker is worn pretty bad, looks like a CH23S 76513.

A friend of mine has a substantial oil leak, We see it dripping off the lower starter bolt about every 45 seconds one drip. He cuts a residential lawn that takes about 5 hours a week, he is using about 8oz oil per cut. The motor had so much oil all over it that it was difficult to really see...

The tires were slicks from the factory

I have a 10 year old RZ4219 and the smooth front tires won't hold air. They are a size 11x4.10-5. I see replacement tires and tubes in size 11x4.0-5. It's not quite the same size but close. Can I use the 4.0 tube instead of the 4.10 tube or should I just buy new tires or tire/wheel combos...

Just to close this out incase anyone else is searching this problem, turns out it was just a worn belt. So the symptoms were one side not pulling as good as the other for the last few cuts of the season. Parked it over the winter then it wouldn't move at all. Replaced the drive belt and it...

Thanks for the tip, that makes perfect sense because it drove into the garage under it's own power just a few months ago, seem's unlikely both drives went bad just sitting for a short time. I'll check the idler for the hydro drives. It has to be something common to both drives, I just didn't...

I drove the mower into the garage after the last cut a few months ago. I went to the shop today to replace the deck belt because it popped off during the last cut. After replacing the deck belt and starting the mower it would not move. I checked the neutral levers in the back, put them in...

I have a RZ4219 that has a problem with the right side not being as strong as the left side. When going straight on flat land it seems almost ok, but when I try to pull up a hill or push the right side steering handle forward I can tell that side transmission is not responding like it is...

I haven't noticed any quality of cut issues, although my yard is relatively flat. I can see high speed cutting on uneven ground could cause a possible uneven cut. Tire pressure as well. I did notice that my mower came with some seriously over inflated tires. For my use this machine is awesome.

Just an update...I've had this machine for about a year now, I'm at 24 hours and I love it. I changed the oil after the first couple of hours and I blow the deck off after each cut. My battery was dead when I went to start it a few weeks ago but that was because my cheap Harbor Freight...

I'm thinking of getting a ZT2 for my 1.5 acre yard. I have a lot of trees and obstacles plus some roots on top of the ground (one of them took out my Husqvarna RZ4219 deck with no front rollers.) I also have a ton of leaves that fall late in the year and watching a few videos online it looks...

I'm looking for a pulley fan for this pump - ZC-DPBB-2M5A-2WPX. When I go to the Hydro Gear website they show the pump OEM part id is 1403. Either way, I cannot locate the fan. I called a local dealer and he couldn't locate it. I got the pump # off the sticker on the pump. Any suggestions...

Has anyone replaced this? I cannot locate the part on any parts diagrams. My belt wore out and it bent a few of the blades as it jumped the pulley on the right side motor. I'm thinking I can cut the bent portions of the existing blades off and roll on, any reason I shouldn't? I cut about 1.5...

I'm having trouble figuring out how to replace the drive belt on this mower. I jacked up the back end and removed the deck belt. The drive belt looks like it cannot be removed unless the tensioner pulley/bracket is removed or the rear transaxle is lowered. Is there a trick to doing this? Any...

Does anyone know if you can add a hitch to this mower? I just want to pull a small tractor cart occasionally. It has a tubular rear bumper. Any advice? Thanks

Can anyone tell me if this is by design or is there something wrong with my mower? It has about a 2 second delay before it starts to crank when you turn the key to start the mower. Anything I should be concerned about? Thanks

I first noticed it in high gears, now it does it in all gears. Seems to slip like the teeth on the transaxle gears are stripped, but I opened the case and all the teeth look good, axles are staying in place. The chain seems like it might be a little loose but not enough to cause the trans to...