Search results

Post the model and serial numbers for your unit so we know what you are working on. We hate making guesses.

To my knowledge those are casting lines made when the block was cast. I personally have seen them many times and wouldn’t worry about them. Remember read my signature.

Now I’m confused, as both those numbers come up as 28” models. One model has both a 28” deck available and a 30” deck available. To me it may be possible. Use these three web sites for see if they can be interchangeable. Very hard for us to give you reliable information, because we don’t have...

Has anyone checked to see if the deck is sprung from hitting something. Might have happened when someone hit something and people started throwing parts at it. Doesn’t sound like people are checking for all possible causes, just assuming they know the problem without checking.

I’ve seen GCV160 carbs for less than $20. It will depend on the full engine numbers.

Check battery voltage while turning the key to the start position. If battery voltage drops below 10 VDC the battery is shot and needs replacement. Wouldn’t be the first time the battery reads good, but drops under load.

At the price of Honda carbs I wouldn’t waste time trying to clean it. I would just replace the carb.

If you feel it is rough when spinning by hand, go to dealer now. Be proactive and do not wait. Let them grease it if that’s what it needs. You will also have a record if something happens down the line. That’s why you have a warranty.

Did a google search and found this, which is 48” long...

Nothing surprises me any more. That’s why I try not to assume anything and check everything I can think of. Making mistakes has been my #1 learning tool.

Don’t know what manual you have, but page 7 of this manual tells you exactly how to check oil level. https://bsintek.basco.com/BriggsDocumentDisplay/default.aspx?filename=mssAJP-K_ny7tH217FzoPu

I definitely agree, but first check your oil level and see if it smells like gas gas. If the level is high and it smells like gas you’ve found your problem.

Definitely would have the dealer check it out ASAP, as if could be a bad bearing.

Without knowing the model and serial numbers for both units we would have to offer guesses only. Guessing normally ends up costing $$$$, so we request that you provide us with those numbers if you don’t to spend a lot.

Must’ve had a brain fart when I posted .020”. hlw49 is correct at .008”-.010”. Sorry about that.

Air gap should be set at .020”

A single blade mower which leaves a high part down the middle? This is something I’ve never seen. Going to keep my eye on this thread, as I want to see the solution.

Did you level the deck by using the blade tips or deck shell? Did use an OEM belt? John Deere tractors are very fussy. Is the center blade turning as fast as the outside blades? Will need an assistant to help with this. Are you mowing at full engine speed? All these can contribute to the...

First thing to check is a level deck. Check your operators manual on how to adjust the deck.

Sorry I didn’t go back and read all posts, Just reacted to the posts on this page. I did say it was a stupid question.

I wish I had a nickel for every time I’ve seen a DIY guy make this mistake. In 40 years working on Toros I could but myself a good steak dinner, even at today’s prices. Should add that most guys or gals never replace the fiction ring behind this clutch washer.

Time to ask the stupid question. Have you tried putting in an inline spark tester to determine whether it is a fuel problem or ignition problem?

Check the oil level, see if it smells like gas. Remember Honda mower engines, the oil level is checked WITHOUT screwing the dipstick back in, just resting on top of the fill tube. Very unusual problem for Honda engines.

Had one like that a few years ago. What I found was that the blade was slowing down or just stopping because the belt was not riding correctly in the pulley. Replaced with an OEM belt and made sure the blade brake was fully releasing. Have some watch the problem spindle when cutting wet or...

Section 7A of this manual describes how to install the rewind spring. www.tuks.nl/WFCProject/img/Engine_Carburator/81644210-Briggs-Stratton-Service-Manual-L-Head.pdf

I doubt it.

This is a 3 year old thread, probably found a match by now.

This manual should answer 90% of your questions. https://www.lawnmowerpros.com/pdfs/snapper/07224.pdf?srsltid=AU7gw4Xv3YxBobcli3Fotw7I5Gl69GkpB-2hangJ1QNC3VleIll45mLX

You now have a mechanics nightmare. Using the wiring diagram that Star posted and a VOM you have to trace the wires to find a voltage drop. In this situation time and a great amount of patience is you friend.

Google search “How to adjust the drive cable on a honda hrx217vla lawnmower’. You should find your answer.

Please post all engine numbers and we should be able to find you an individual parts list and possibly a service manual.

Try this troubleshooting procedure I’ve posted many times. Electrical problems can be very easy or very difficult, depending on four things. 1. How well you understand basic electricity. 2. What tools you have and know how to use. 3. How well you follow directions. 4. You don't overlook or...

You are correct, I attached the wrong manual. Service manual for that engine is Tecumseh part #740047 which I can’t find a PDF format.

I looked at the parts breakdown again and I’m wrong. Your engine does use a flywheel adapter, not flywheel key. Trying to explain its use is difficult so do do a google search “what does a tecumseh flywheel adapter do”.

I’m thinking you need an offset key. Probably one of these. https://www.jensales.com/products/flywheel-key-fits-tecumseh-611004?gad_source=1&gad_campaignid=19240832329&gbraid=0AAAAADttYvN1YsWmHKRlQ7hSIuF5zGak1&gclid=EAIaIQobChMIoqeLkPL9lgMVm6TCCB1ofglREAQYAiABEgLOTvD_BwE...

Section 8, starting on page 20 of this manual describes how to do it. Shouldn’t be very hard. https://www.toro.com/getpub/22446

Hammer makes a good point, battery or magneto? 301 came with both systems "

The first 10 pages give you a good overview on how the magneto ignition system works. I don’t know how much more I will need. The only part of this system that is hard is setting the timing. Other than that, easiest system to to work on.

Sounds like your charging system is not working. With engine running, at full speed, and no blade engagement, measure voltage across the battery terminals. It should read more than 13 VDC. Less than that I suspect bad voltage regulator or stator.

We need model, type and code numbers. Should be stamped on one of the valve covers.

Please post engine spec number so we know which electrical setup you have. This manual may be of some help. Section 8. Im assuming you have a setup using an automotive style coil. I know assuming is not a good idea, but I’ve been wrong before. A couple more things I would check. 1. Do...

If pulley bearings are bad the belt will not have the proper tension and will wear faster and jump off.

Sounds like rocks in pulley? Bad bearings.

Try this procedure to identify your problem. Post back with results. Electrical problems can be very easy or very difficult, depending on four things. 1. How well you understand basic electricity. 2. What tools you have and know how to use. 3. How well you follow directions. 4. You don't...

Experience has told me with these tractors adding attachments is not worth the money. They are lawn tractors. The only accessories I would get are a small wagon and a lawn sweeper. I definitely would not add a snow blower.

If you properly maintain it, my experience says maximum of 5 years. If you get more than that you’ve got your money’s worth.

That is a belt guide. In this manual go to page 16, part number 10. Should be mounted close enough to the pulley that so the belt will not not jump odd the pulley when the tension is released. https://apps.mtdproducts.com/manuals/769-04806.pdf

Congrats, your patience and double checking paid off.

Used an ultrasonic cleaner since they came out, probably can count on one hand when they haven’t worked for me when used properly.

Simple answer, YES. Should add, google search “HOW DOES AN ULTRASONIC CLEANER WORK “. It should answer your questions.