Search results

And you know this...how? You watching the inner race as the machine is moving? On the ground? If it makes you feel better grease the shaft but that would just let the inner race be more likely to overcome friction. Or leave it dry.

Common testing standard: Most small engines are rated and tested at 3,600 RPM (no-load or governed speed). At this speed:Many Briggs & Stratton systems (e.g., 5A or 9A charging) produce ~28–40V AC (28V for smaller 5A systems, ~40V for 9A). doityourself.com Other common readings: 24–30V AC...

⛔

Block cracking is the last thing that would happen. A bent con rod is more likely. Take pictures with your phone of carb removal and disassembly.....assuming you have a cell phone.....at every step. Don't think you'll remember and skip....take pictures. Different angles. Once apart spray or soak...

⛔

Aaaaand....I'll wager that the old starter is just fine only needing disassembly, cleaning the commutator, and inspecting the brushes and reassembly.

And 10% ethanol is just fine.

Generac had this issue with Generac branded air filters they sourced from Malaysia. The specs from Generac called for a fireproof coating on the filter element. It was fireproof, alright. Under light load and lighter airflow requirements it was just fine. But if a heavier electrical load showed...

Mechanics Mode Mechanics mode allows dealerships to unlock/power up the console and operate the mower without the owner’s key code. Enter the mechanic’s key code using the buttons (1-4). As you enter the key code, the LCD (14) displays it, always showing the 6 most recently entered digits. If...

https://static.visionamp.org/rubix/20240219/f88d99186413030259645db1020aaf5f5576cb88.pdf Here's the wiring diagram. Seems pretty straight forward.....

Tires have vent spews.....🤫

B&S now making Kawasaki?

I often wonder what those arrows and the "P" on the pump mean? 🤔

You'll need a pressure regulator that gets down to the 1 to 2 pound range, preferentially the lower of the two. Or just get a pump with an adjustable regulator. I did this in an old Craftsman when I lived in PA as the hills would prevent the vacuum pumps from moving fuel to the now much higher...

Not familiar with this item....but, see if this helps. One of the few references to this marque and roller as a search term....

Yup. These coils tend to age over the years as this is a lost spark system that fires every revolution, not just when that particular cylinder calls for spark. Multiply 3400 x 60 x the number of hours on the engine......that's a number in the millions. These are...

Wish these forums had a search function.....anyone ever confirm that the coils were actually putting out proper spark? And that the coils were mounted in the correct location? Kawasaki twins have a left and a right coil that are different and separate from one another....can't vouch for the...

You don't lose just 50% power on the loss of a cylinder....more like 75% with pumping losses and additional frictional losses....and that depends on whether the compression isn't degraded from hours use. Plus it's turning those two hydraulic pumps when moving and stationary but the load only...

TruFuel saw you coming......

Sure looks like it fits to me. 🤫🙄. Found your "kit" for $11 elsewhere on Amazon but you need the new spindles and the bearing still won't fit the wheel hub.

The ball size would be vanishingly small on a 3/4 id and 1 of bearing...l that is why you're finding 1 3/8 OD...and , yes, that is the race size not the flange diameter. Ball bearings with a 3/4" ID are widely available, but their OD is almost always larger—most commonly 1-3/8" (1.375") for...

Says nothing about the OD in the specs.....

Also..those holes in the side of the jet are air bleed holes to enhance emulsification of the fuel drawn thru the jet bottom. Make sure the air passages are clear as well.

Does it surge still with the air cleaner removed?

Without seeing the complete assembly I'd check to see if there is room to weld your reinforcement plates on the ends of the bracket to form a semi-box, assuming that this would not interfere elsewhere, and remove the center previously welded reinforcement. Looks like the bending is orthogonal to...

Almost every two stroke has the pin unless the ports are miniscule and even then...hell, .21ci RC engines have the pin.

Bet the starter has never been renewed...ie brushes, commutator, lubricated bearings.

No....unless your card company is scamming you too, it doesn't need to be on your "statement". Initiate the dispute as fraud and they'll provisionally reverse any payment pending resolution. Save the advertisment as proof of fraud.

And too rich gasoline will behave similarly to a too rich propane. There is no opposite.....

No, that's about right. If you consider gasoline (e10) to be 1.0 Gasoline Equivalent then propane is about 0.76 Gasoline Equivalent. You'd need 1.52 gallons of propane to equal the BTU content of 1 gallon of gasoline. Motor gasoline, 1 gallon=120,214 Btu Diesel fuel, 1 gallon=137,381 Btu...

If you know nothing, don't reply. 🙄

No.

Yes. I know.

Cosmoline for the old timers. Close to a wax so not great if it dries out completely.

"....initial oil put into their smaller EXI series vertical engines when new is considered "lifetime" and to check and only add new oil as needed. Basically, that means run it until it wears out, then throw it away and buy another." "Engineering" retards just love "lifetime" crap. 111 hours...

I run a couple of passes of Forney Super Wear weld across the face of new blade edges that have been preground to a flat edge and grind back to a tapered profile. Much better wear resistance at 65 Rockwell than the 38 to 45 Rockwell of most carbon steel blades. You could also heat and temper to...

Is this a two stroke? Should oil actually end up in the combustion chamber on a 4 stroke? The engines are assembled with lubricated walls already. The oil ring at the bottom piston land scrapes the oil back down the cylinder to the sump. That's it job. The other compression rings should be...

https://www.mtdparts.com/en_US/all-products/harness/725P13068.html

Called an adjustable, greaseable heim joint.

Tie rod end....https://www.amazon.com/s?k=screw+on+tie+rod+end+for+riding+mower&crid=6HF57Q5WC95B&sprefix=screw+on+tie+rod+end+for+riding+mower%2Caps%2C260

https://www.osibatteries.com/honda-31500-vh7-800-lawn-mower-battery

http://www.faqs.org/faqs/autos/gasoline-faq/part1/ Octane has zero to do with BTU produced. Gasoline has 42 - 44 MJ/kg. iso-octane has 44.374 MJ/kg. Virtually the same. The only reason octane is in the mix is to slow the flame front down to controllable rate to prevent detonation in high...

Like this....I've found a ton of these online. It might be easier to search by the battery size and terminal configuration than the ID alone. https://www.upsbatterycenter.com/bb-shr3-6-12-12v-3-6ah-battery

Lead acid batteries......

Are you just setting the high and idle screws per the instructions or have you adjusted while running. If you know the difference between a four stroking and two stroking two-stroke sound when running, good. If not, experiment by richening the mixture and you'll hear a definite change in the...

That is also true....been watching Cutting Edge Engineering's YouTube channel out of AUS....some of the prices are outrageous for parts not obtainable there. 10% Goods and Services Tax (GST), a 5% duty on the FOB value for most machinery, import processing charges, and biosecurity fees. Why a...

You don't have a clue about import fees, do ya. 🙄

I'm at a loss about your "fuel shut off" . Is this the carburetor solenoid or a manual valve? The solenoid is only $16 or less from plenty of sources and there isn't any $170 fuel parts anywhere on this engine.

Don't pay attention to some of the "advice" you're getting. Some of these guys think they're God's gift to mechanics. Others are the real thing. You're on the right track. If some of these guys had just picked up on the fact you had a bore dial gauge and had used it to get a .0008 out of...

Christ almighty.....🤫🙄