Menu
Home
Today's Posts
Unread Posts
Trending
Search forums
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Mowers
Repair
Buying Advice
Operation
Pro Talk
Photos
New media
New comments
Search media
New
New posts
New media
New media comments
New profile posts
Latest activity
Log in
Register
What's new
Search
Search
Search titles only
Latest activity
Register
Menu
Log in
Register
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Auto Doc's's latest activity
A
Auto Doc's
replied to the thread
Issue with Walker C19 Zero Turn Mower
.
Hello Stephen, Vented fuel caps went away a few years back, so more than likely the auxiliary tank vent hose is plugged. They tend to...
Oct 22, 2025
A
Auto Doc's
replied to the thread
Issue with Walker C19 Zero Turn Mower
.
Hello Stephen, Vented fuel caps went away a few years back, so more than likely the auxiliary tank vent hose is plugged. They tend to...
Oct 22, 2025
A
Auto Doc's
replied to the thread
Sheared/Broken Crankshaft Keyway.
.
Hello C., A crankshaft (the part alone) is typically not that expensive, but the intense labor to replace it is. If you are...
Oct 22, 2025
A
Auto Doc's
replied to the thread
Sheared/Broken Crankshaft Keyway.
.
Hello C., A crankshaft (the part alone) is typically not that expensive, but the intense labor to replace it is. If you are...
Oct 22, 2025
A
Auto Doc's
replied to the thread
Backfiring from full throttle to idle
.
If spark plug heat ranges are that cold, put the correct plugs in. People tend to think spark plugs are all the same, but they are not...
Oct 22, 2025
A
Auto Doc's
replied to the thread
Nikki carb OE4215 jet size for Generac 27hp
.
Hello T, Going a little rich will keep the cylinder temperatures down. A basic rule to remember is fuel cools down and air heats up...
Oct 22, 2025
A
Auto Doc's
replied to the thread
Nikki carb OE4215 jet size for Generac 27hp
.
Well, as it turns out I have only one match. It is a steel bowl aftermarket carburetor (The bowl may not be correct for the...
Oct 21, 2025
A
Auto Doc's
replied to the thread
Ariens 915268 Ikon 42 zero turn No crank !
.
Purple with white stripe is positive, black is typically ground. If you are hacking wires to test you are going off the rails with...
Oct 21, 2025
A
Auto Doc's
replied to the thread
Ariens 915268 Ikon 42 zero turn No crank !
.
If it has a low oil switch it will not prevent cranking the engine over. It will just not let it start and run. Worn out ignition...
Oct 21, 2025
A
Auto Doc's
replied to the thread
Nikki carb OE4215 jet size for Generac 27hp
.
I think I have what you need. What are the numbers dot marked in the top of your housing near the fuel inlet tube?
Oct 21, 2025
A
Auto Doc's
replied to the thread
Nikki carb OE4215 jet size for Generac 27hp
.
Have you tried Parts Tree. I have had luck finding jets on there. The O-rings for press in jets are not available by themselves and only...
Oct 21, 2025
A
Auto Doc's
replied to the thread
E180 Transmission ?
.
JD riders don't work at that altitude. LOL Smaller rider mowers Hydrostatic transmissions are no good on hills unfortunately...
Oct 21, 2025
A
Auto Doc's
replied to the thread
Timecutter Valve Adjustment
.
Hello R., Kohler command has hydraulic lifters. Kohler courage has adjustable rockers.
Oct 21, 2025
A
Auto Doc's
replied to the thread
Poulan Pro PR5020 adjustment and questions
.
This motor needs a cylinder and piston. That scoring is very bad like straight gas has been run in it.
Oct 21, 2025
A
Auto Doc's
replied to the thread
Cub Cadet XT2 decision time- new or used?
.
Hello M., We are heading into winter, so it is also a good time to negotiate deals. Is the used one a dealer trade in or private owned...
Oct 21, 2025
Top