Search results

when i pull yhe mower backwards the wheels won;t move. some one told me there is a spring that controls that, but i can;t see anywhere a spring goes, is there a diagram of it anywhere,

can any body tell me where to get a good diagram of the throtle and speed cables for a jx75

will a 380 cranking amp battery be big enough for a briggs opposed 20 hp 461707-0143-E1

i have a briggs 461707-0143-E1 and i took the carb off to clean it and now i can;t see how to put back on. can somebody tell me where to get a good picture of the linkage setup.. i looked at the diagrams but they don't show where to hook up the black throtle plate on the carb.

i have a JX75 self propelled mower and i can;t pull it backwards, does the pinion gear on each wheel have to be on the excat wheel or the interchangable. i think there is a right and left on them but they are so worn i can hardley make out anything.

why is it that my honda surges unless i have a air filter in it.

the number is 1691537 mdl. serial is 5789 got this mower for free, and its in picies. yhe diagrams i found are not very good, on the deck there is a long bar that goes from the brake on the deck but i can;t see where it goes on the mower. and the up and down adjustment dosen;t work. WHERE can i...

starts and runs fine, but wen i hit the forward or reverse it won't move. the freewheel lever is all the way in, but it dosent make any difference if its in or out it freewheels eather way.could the trans be shot. i dont know any more i can do.

have a 12 horse vert briggs, and i can[t get it to charge battery, tried a new stator hooked it up to the hot side of the battery, and it still won;t charge. could i have gotten a bad stator, how do you check them to see if they are working/

have a lawnboy 10330 ser 9901215 tried two new carbs, still not getting fuel to plug. anythin else i can try, and oh yea iam getting spark.

wiring burnt up on ridding mower, need diag. for simple 3 post pushbutton switch; already have the kill switch hooked up.

i have a tory wheel horse, the wiring burnt up, and i want to rewire it, can sombody send me a drawing, simple wiring of just the starter coil and solenooid to switch, no safty switches.

i have a toro rear engine mower, and it won;t do anything by turning the key, i can pull the wire off the coil and jump it direct to the starter.and it will run, or i can jump the solinoid and it will start but not the the key. could it be the solinoid or some thing in the wiring.

anybody know where i can find a recoil spring rewinder tool for 2cycle , i had one but i can;t find it.

can you repair a ball joint on a lt180 mower the steering ball joint keeps popping out. i have it taped on now but is there any way i can fix it, they want 30.00 fo a new one.

I have a john deere tractor with a leaf vac on it and the motor is blown, 5 hp kawasaki fa2100 all it has on it is powerpack fa2100. i looked for another motor but i can;t find anything on it. the motor is on the leaf vac. any body know where i can get one.

i don't know what mower this came off of the guy said there were no name on it. but the number on the switch is 3497644, i can't find one. is there a replacement for it.

i have a kawi. motor, i pulled the fuel pump and the plunger won't move when i turn it over. also it won't start on spaying starter fluid in carb.i know you will want the numbers on it but i can't find any/ its off a john deer mower and its water cooled.

i have a toro 71184 ssn. 5913447 and on the deck it has a bell crank, i can't find a good diagram of how the inghage cable goes from the handle to the bell crank. there are two plastic pulleys. i must not have the cable on right because there i a lot of slack in the cable after i disingage the...

ibought a brand new carb for it and it still won't start. put my finger over plyg hole. and it has comp. i tried adj the carb. started at 1and a eighth turn, nothing. it seems the plug is not wet. so iam lost. ANY SUG.

have a 10523 6905547 lawnboy,anybody know where i can get a carb 94-5738 for it, i looked everywhere.

i have a 5hp horz. briggs, and it needs a new carb, one of the legs broke off and i can't bolt it back on the motor. my problem is putting it back together. there are so many linkage and iam not sure where they go. is there a diagram fhat shows where they go, i downlowed a diagram but it just...

I have a 8hp briggs vert. engine and i can't find a throtle control plate anywhere, ebay, parts tree. does any one know where you can still get one. its mdl# 1707-1515-01 code # 88011610 thanks.

I have a stx38 black deck, and i put a new drive belt on and it runs fine but now iam having trouble shifting gears., i have the brake in the whole way but it seems like its not enough. is there ans adjustment, all it does is put slack in the belt right!

REPLACED THE IDLER PULLEY BRACKET AND I NEED TO KNOW WHERE TO HOOK UP THE TENSION SPRING, EVERY MANUAL I LOOK AT SHOWS THE SPRING BUT NOT THE LOCATION. CAN ANYBODY DRAW A PICTURE OF WHERE IT HOOKS ONTO THE FRAME AND IDLER BRACKET.

i have a 11hp briggs vert. engine old type with the solid type carb the number is 252707 0660-01 and where you have the control plate for the throtle and choke. One of the small holes that hold the plate on is stripped. do you think jb weld will hold new threads.

I have a snapper rear engine rider wit a 8 hp briggs pull start on it and i want to convert it to a electric start. i need a electric flywheel but they are no longer avable, they do have the ring gear, they say bolts on the bottom of my org. flywheel. but dosen;t it have to have magnets in it...

it seems like it is getting fuel throu the carb but the plug is bone dry, and when i put the ing. checker on i get fire to the plug but not through it i tried several plugs. i think its because the head is alum. and can;t get a good groound. ius there any other way to check the fire.

i have a husqvarna AWD 96145001101, 111913m003146, i hit a baseball in the yard, and it broke all the plastic at the rear drive. including the cable. i replace everything, but for the life of me i can;t see where the drive cable hooks to the rear drive.there is a hole in the belt guide but it...

just bought a new carb from china, the primer baulb fills up but no fuel goes into the motor, do you think that its just junk , or is there a fix.

i have a 2 cycle engine on a toro snow blower,and it just surges, i tried a new carb but it does the same thing. there is something on the shrould that looks like a condenser any ideas.

i have a 2 cycle toro snowblower, and it starts right up, but i can't stop it from surging. i thought it was carburetor so i cleaned it but it made no difference so i bought a new one, and it does the same thing.changed plug, still the same. there is something on the schroud that looke like a...

i have a 10 horse tecumseh and every time i pull the starter i shear a key. what would cause this. i spin the cam by hand and everything is free.

I got my snow blower out to check it out and after awhile it startwd to shoot oil out of the valve cover tube. it was alful thin, could be gas mixed with it, so i replaced the carb. anit still shoots oil out. any sugestions.

Can somebody tell me what horse power and what engine this is. ever thing is painted over except the model # which is 536.918900 and the number on the engine is 143 736102ser3272D

i have a snapper 6hp 2 stage snow blower, the book calls for 410-350-6 tires. but the tire says 410-6 so i bought a 410-6 tire. but it looks thinner than the one thats on the rim. will it expand when its installed on the rim.

I have a rear engine snapper mdl. 265x cant find serial; number. I put a new engine on it and I want adjust the plate on the bottom of the engine to the friction wheel. what gear should it be in to adjust. or whatever. is there a manual I can get that will show it. I went to snapper web site but...

iam rebuilding an old snapper rear engine rider and iam putting it back together and wher you adjust the belt I have the clamp tight, but when I lift the rear off the ground it spins on the shaft, it won't go in or out. just spins and I can't get the clamp tighter. ius this supposed to do...

iam working on my friends cub cadet 1020. he says he was mowing and it just stoped. the engine runs fine it just won't move at all. not forward or reverse. I looked and it has fluid in the tranny. but I didn't get undr it yet. does it have a belt to the transmission or is it hydrolic. it says...

I just put on a 12.5 brigs engine on my old snapper rear engine rider. mjy question is do I need a voltage reg for the statter. I just priced one and they want 68$ for one if I just run the red wire to the hot side of the battery will that be enough. I know the other wire is for ac. just the...

runs good for about 20 min. then sputters and stops. let it sit for awhile then it starts and runs for about 20 min. I thought maybe a coil, I put a checker on it and when it stops and I try to start it right away I get spark. so I thought it might be the fuel solenoid, so I changed it with one...

I have a 12.5 briggs inteck 219807 the gov teeth were all chewed off so I replaced it and it ran fine. now it just seems it dosen;t have any power. the engine seems to be running at top speed. there is just no power. will the carb do that. I pull the gov manually and it doesn't speed up. its a...

I have a STX38 yellow deck and I bought a new chute and hinge and for the life of me I can't figure out how the spring goes, can any body draw me a diagram of how it goes. I looked every where I can think of. and I can't find anything on how it goes.

I have a lawnboy10546 ser 7904307 with electric start, it won't start woth the electric start, but one pull with the cord and it starts right up. the electric start spins the flywheel thw same as pulling the cord. but it will not even attempt to start. does that bosh plug by the starter or that...

Can anybody tell me who bought out noma, I am working on a noma snowblower mdl. 56132 ser#2000461 and iam trying to figure out where the little plastic wheel for the auger cable goes. if some one knows where I can find a break down it would sure help.

I have an old snapper rear engine rider that I took off the 8 horse and put on an 11 horse 252707-0633-01 and I have tried two carbs rebuilt, and I can't get rid opf the popping. when I speed it up it pops and when it idles it pops. could it be internal. it starts right up ,idles speeds up, it...

I have a noma G2450000 snow thrower and I was told they were bought out by murray. does anyone know where to get parts. I need a auger cable.

iam new at this chain saw business and is it my imagination or do these have a nak to starting them, I put it on the ground and pull the starter but it dam near lifts me off the ground. it feels like its catching on something but I take the plug out and its smooth pu;;ing,do these have that much...

I thought I would get out my snow blower and get it ready just in case we get snow this year. noticed some old fuel still in carb. thought I ran it dry.well it surges really bad. so off came the carb for a cleaning, no help. so a carb kit. no help. I have a new carb on hand, but its a...

I have a 10521 rear wheel drive. can you tell me where to find a diagram of the pinion gear and the rest, I tried the reg diagrams but they don't show which directions the dots on the pinion gears go. I tried both ways, it will free wheel withot it running, when I start it ,it mowes fine but I...