wiring

Hello everyone. Newly joined today in the hope that there's someone out there who can help. I have a Vanguard 16hp V-twin engine.( Model No; 303777) I bought it used. The wiring and cables were cut off by whoever removed it from whatever it was in. I believe a ride-on mower as it is the...

I’m making this post for a buddy of mine, he got his hands on a free John Deere 160 lawn tractor with no motor, and we had an old Agway lawn tractor laying around as well with an 18HP B&S opposed twin. We decided to remove the twin from the Agway and try to cram it into the 160, but all the...

I have a craftsman lt3000 my dog got ahold of it and ate my harness would anyone be able to get me some pictures of the harness by the starter

Got this unwanted lawnmower as freebie and cleanup carburetor which had choke open stuck and rusty, replaced spark plug and when repaired two cut wires green and yellow-white on safety seat cable switch I was able to make it run only when the gear is in reverse position. Checked all switches for...

John Deeree X590 SN:161099 (not sure of the year model......2023+-?) I would like to replace the blank switch cover (the one intended to serve for the optional mulch system, I think), on the dash, with a Carling Techno, Contura X switch, V6D1S001. This switch has 3 terminals: 1 power in...

Model 13B9A1CS010 ser#1D108H40176 115hours Won't turn over. When starter button is pressed, LCD shows voltage for ≈2 seconds, then a barely audible relay click in the keyswitch and hum (fuel pump?) and showing hour meter, then nothing changes until timeout. No (louder) click from starter...

I have the 12 volt plugs already wired to my ventrac but I need help wiring a third party spreader. It has a red and black wire but I need help attaching it to a ventrac 4 pin plug. I found a wiring diagram but can’t seem to get it to work. Any suggestions? Thanks

Gentlemen, recently aquired a John Deere LT133 M0L133A054289 from my father-in-law, who picked it up in a yard sale. Machine was missing it's hood and battery. Judging from the condition it had been in a flood at some point but someone had made an effort to wash/clean it, even had fresh oil...

Howdy folks, I’m an older fella trying to get my old John Deere JD400 back in working order. I’m swapping in a Briggs & Stratton 386447 engine (left side muffler) to replace the tired original. My main concern is how complicated the wiring will be for this swap—especially since the harness on...

My 32 year old lawn tractor finally blew up and I am replacing the 12.5 hp Briggs that had no voltage regulator with a 28P777 0641 A1 14 hp Briggs that has a voltage regulator. 1) Do I simply hook the red wire on the regulator to power off the switch? It is a 2 wire voltage regulator if it...

I have this CC Z Force that has no power to the anti-backfire solenoid with key turned on. Solenoid tests good when powered manually. Mower Model number 53AA5A7M710 w/ the Briggs & Stratton engine. Engine runs but only with full choke on to suck fuel past the solenoid plunger tip. Carburetor...

Does anyone have a better wiring schematic other than the one in the owners manual? The one in the owners manual is lacking in text. I saw one for an OUTLAW that identifies relays and components...ie: Seat relay, pto relay, ignition switch, battery...etc etc.

Hi There,I'm in the process of trying to get an old LX178 up and running but sadly it looks like the ignition key module is knackered. My question is can I bypass this module and modify the wiring to provide a working machine or is the key module linked into the ignition control module on the...

My Bad Boy outlaw red wire on the voltage regulator has come apart and I’m not sure where to reattach it. Any help will be appreciated. Thanks Henry

I have a Dixon ZTR 60” Kodiak mower with a 25 hp Kohler command pro engine. I bought it a couple months ago and was told it is a 2009 model. I can’t find any tag showing model or serial number. I’m looking for a wiring diagram. Some diagrams that I have found show a circuit breaker. Mine does...

Hi, Does anyone know where to get the male mating connector to plug into the wire harness on a Kohler CV23 engine? Part numbers and manufacturer wouldn be greatly appreciated Thanks, Carey