flywheel

Hi everyone, I’m looking for some advice on a Briggs & Stratton 31C707 Type 3346 G5 engine. The problem started when the flywheel magnets came loose and struck the stator while I was cranking the engine with the starter motor, causing the engine to lock up. Since then I have: Installed...

My JD L100 lawn tractor stalled on a flat the other day, just stalled but accompanied by a hard to describe noise sort of like something spinning down. After that I got only a solenoid click. I tested the battery at 12.2V, but under load only 10.2. On Sunday, it is easier to replace the battery...

Briggs & Stratton Flywheel magnets: Are there one or tree magnets and which POLE orientation? See appended 2 files

So here's a video I made today so the background story is Friday I started noticing white smoke coming out of the muffler took off the air filter and there was white smoke coming out of that I was thinking it's probably a head gasket so I took off the cylinder head and removed the spark plug and...

Is anyone out there that can lead me to a briggs flywheel 808766?

I am having no luck pulling a Honda CGCV190 flywheel. I have tried a 2 leg puller with out any success. I am thinking that arms on my claw type puller squeezes the top of the flywheel and is not pulling straight up enough. I have ordered a 8 inch puller that gas straight arms and will allow...

I have a Cub Cadet LXT-L46 Fab with the Honda GXV630 engine and about 9 months ago I replaced the starter and ever since then more often than not, the starter will just click, click, click and nothing happens and finally it kicks in and spins the engine. Upon a close inspection I realized that...

I have a 10hp horizontal shaft engine model #204412-0163E1 I am trying to find the flywheel or ring gear for electric start. I ordered a new flywheel from briggs and stratton p/n 794814 but it doesn't have ring gear. The parts lookup pic shows it with ring gear but it doesn't have one. Can...

I have Husqvarna yth22v46 with a Briggs 22hp model 445777-0231 -E1 and I was replacing the starter drive gear and the only way to get it back on was to remove a block and screw on the flywheel but the screw wouldn't come out so I drilled the head off to back the bolt out but the magnetized...

I have Husqvarna yth22v46 with a Briggs 22hp model 445777-0231 -E1 and I was replacing the starter drive gear and the only way to get it back on was to remove a block and screw on the flywheel but the screw wouldnt come out so I drilled the head off to back the bolt out but the magnetized block...

I have Husqvarna yth22v46 with a Briggs 22hp model 445777-0231 -E1 and I was replacing the starter drive gear and the only way to get it back on was to remove a block and screw on the flywheel but the screw wouldnt come out so I drilled the head off to back the bolt out but the magnetized...

Any tips as to how I should attempt to remove the flywheel from my Kawasaki FH580v? As you can see in the photo it is held on by bolt, not by nut and there are no holes to attach a wheel puller. I've watched several videos, but none seem to apply to this engine. I'm trying to access the...

Hello guys, I'm trying to remove the flywheel, because I suspect something may be wrong with the key. My motor won't start (it turns over though). Somebody suggested il might be out of timing, and to check the key; sometime the timing goes out of wack because of a broken key (checked fuel...

help, i have a troy bilt 13an77bs011 riding mower i need to take off flywheel cover under the shroud. so does the nut ,that sits on flywheel inside cover turn clockwise or counter clock wise to remove. i think the pin is sheared thanks