dixie chopper

Blade pulley on left while seated has an issue with being pushed into the frame and pushing the upper lip down on the belt. Causes belt to come off. Have changed from the 5.25" dia to the 4.75" dia pulley to no avail. Made a bumper between deck and frame to try and solve the problem but that has...

Blade pulley on left while seated has an issue with being pushed into the frame and pushing the upper lip down on the belt. Causes belt to come off. Have changed from the 5.25" dia to the 4.75" dia pulley to no avail. Made a bumper between deck and frame to try and solve the problem but that has...

Wanted owner reliability and performance wanted on Dixie Chopper 2250HP 50 light commercial and Landpride ZSR Razor 54 Estate. The DC has Kawasaki FX 22 PH engine, HydroGear ZT3200, 10 GA welded top plated deck, 17,875 tip speed, 1.25 blade spindles, 23 tires for just a little under 6K. The LP...

Hello me again! On my 2012 had a front wheel bearing on left side fail apart. Looked up the part numbers for a 2012 SE 27/60 which calls for 900340 Bearing Kit which has 4 bearings...2 flanged outer and two inner and a spacer. The ones I removed from wheel was just 2 outer flanged bearings and a...

I'm in search of the lower 50 inch deck. I have the top plate.

So last summer my mower battery would start to drain- it would get to point where if i turned the blades off and tried to turn them back on it wouldn't engage anymore and when I'd go to turn the mower on after sitting over night the battery would be completely dead. So this spring i replaced the...

I'm looking at getting a new Xcaliber 66 in new 2017 any thoughts on this mower or expected cost

I have a dixie chopper xt 3200 stop pulling forward on the right side it will go in reverse fine just not for just make like a grinding noise

Trying to sell for top dollar and my 2008 XC3366 (which I put a new Generac 44 HP motor into a couple years ago) hesitates and shudders in reverse. What is usually the issue when that happens?

Was mowing today and my pump drive belt broke. Well it has lasted 17 years so I guess that is pretty good. Can anyone tell me how to bleed off the hydraulic system so I can tow it to my garage? It has a 25 horse Koehler engine. From looking at diagram it looks like the bleed offs are on top...

Bought new starter and now can't remember where the wires go back on. I had wires not even hooked up and now confused which goes where. Like a dummy, I didn't log or take pic of how I removed them. ANY HELP would be appreciated. There is an orange wire that is detached on both sides and has a...

I have a problem with my Dixie Chopper Iron Eagle. Hydro-Gear ZT-2800 on left side if you were sitting on seat, it goes forward faster than other side and has power. If you try to go in reverse it spins very slow and you can stop it from spinning with your hands. I have taken control linkage off...

I have a Dixie Chopper zero turn Magum 60 inch cut, want to install a ocdc on it, order it ,it came in with no instruction where do I find the instruction?

This past week I bought a new to me dixie chopper that needs some work. When i got it home, the key would light up the hour meter, but i didn't try to turn it over. (I bought it knowing it had a bent push rod, so i didn't try to run it before buying) First step was to charge the battery...

My blades quit turning and I assumed the clutch had gone bad but, not quite sure that is the case. With the clutch engage switch in the off (down position) and the parking brake set the clutch engages and the blades are turning. With brake set and I place the clutch engage switch to on (up...

What Dixie Chopper would be the equivelent to the Exmark Quest ZTR 48"?