clutch

Hi All, Last year the PTO clutch locked up and because of this, I couldn't start the engine as the engine wouldn't turn over. The repair shop nearby told me to order a new PTO clutch and I did and they replaced it. I only used the PTO for 19.1 hours this year and the mower stopped again while...

Update! -No compression in either cylinder. Guessing head gasket? Worth repair or get new motor? Hi. I have a Husqvarna mzt61. Fired it up, engaged pto. Blades spun. Through earmuffs sounded rough\racket and maybe weak. I shut it down. After looking things over, it will not start. Cranks...

A couple of years ago advice from this forum helped me set the air gap on my Ogura clutch on my Freedom Z. Everything seemed fine until recently when I started hearing a loud "scraping" sound seemingly coming from the clutch when the blades are disengaged. No unusual sound when engaged. I...

Working on a 42" Hustler model 927368/ SN 05011533 Helping a friend with his issue: When he turns blade clutch on the engine dies.......mower was operational until this problem developed. I would appreciate help with where to begin the problem search. Fuses are good. Thanks in advance, bartles

third new clutch after about on hour of use, coil overheats, melts, and is toast. no rubbing, not voltage problems, this is on a older gravley and the clutch is straight wired to the battery. volts vary from about 12- 13.5 HELP

Hi, I bought a used Poulan Pro Riding lawn mower (model PP11536LMB) and am having some trouble with shifting. It shifts just fine when the engine is off and the clutch is not pressed, but when I engage the clutch, the shifter will not move. Any help is appreciated, thanks.

I'm hoping there's a few experts out there. It's a great lawn mower that I've had for years. The drive pully finally let go so I was forced to replace the pulley and the belt. The clutch mounting bolt would not come out. Once I used a puller to remove the clutch assembly from the crank shaft I...

I was mowing a yard with my Excalibur. The grass was not real tall but was going through some leaves left from last year so I had the door to the outlet of the deck closed. I was mowing fine and then it wasn't. I was not at my home. so I loaded it back up on the trailer and took it back to my...

looking for a PTO Clutch 5104572FS - hopefully from a source that actually has one available... Ferris said they did, but that was 3 weeks ago now!

I have a 2021 bad boy 54” fr730v engine and the clutch bolt loosens falls out breaks the 5 1/2” bolt that keeps the clutch from spinning. I hate already reinstalled the bolt with blue lock tight but that didn’t seem to hold after 1 hr bolt Fell out again. Any ideas to keep bolt and washer...

I have a 2005 Exmark Lazer (about 700 hrs) and am having a vibration problem with PTO clutch. While disengaged, there is vibration and wobbling of the clutch on the engine shaft. Thinking it was a failed clutch, installed a new one with same result. Worrying about failed lower engine shaft...

Hi All, Mower Info: Snapper Pro S200XT Professional, Model # 5901280. Engine Model Number: Briggs & Stratton 49T877-0010-G1 Quick Summary: Last year I changed the PTO switch because it had gotten loose. Later in 2023, the PTO clutch locked up and I had to have the repair shop replace it...

Hello Lawn Mower Forum. - Is there any chance of some help and/or advice please ? I have owned a Scag ride-on mower for 22 years and about 10 years ago the Warner Electric electro-magnetic clutch failed. I replaced it with an identical clutch. The original had the identification details as can...

2015, G5500. Let off the clutch and the engine dies. Press the clutch and it runs. What could be the problem?

Hi All, I have a Castelgarden XDC 140 which i believe is sold as Stiga Estate 3084 H in the US. The blade engagement is quite severe with the belt squeaking when switched on. Is it possible to add a soft start module to the electric PTO clutch. I have successfully added soft start modules to...

Hi, The Blu/Green, Liner, inside the Clutch/Brake Disc is gone, and going to replace it, but... Is it glued in, and if so, what is the best Glue???

Homelite Timberman45 Chain saw Engine: PS-05867 Model UT10946D I have a Homelite UT10946D 18” chain saw that won’t turn because the chain brake is too tight. When the hand guard is disengaged, the brake band is still too tight around the drum. If I pull the hand guard back just a little, the...

i have a cub cadet lt1040 model 13AX10CG710 that i am trying to figure out what holds the clutch in place, the only thing that i can find is the belt keeper so not sure if this also acts as the clutch stop. can not find clutch stop on any drawing thanks

have a xt2 13wia4cn010 that will not start and clutch will not engage, replace ignition switch and pto switch no change, did a wiring check everything looked good, so i am at a total loss as where to go now would like any help thanks in advance AC

Hello Toro community, I have had white smoke 100% coming from the clutch and the blades struggle to turn on grass even though spindles have been replaced with new sharpened blades. Clutch taken apart, not sure if the problem is one of the bearings or the friction disc. When turning the clutch...

Hello everyone! First off, please excuse my language illiteracy as I really don’t know much about these machines. I was just given this machine by my wife’s aunt as it’s been in the family for 50 years. She said she had it serviced before giving it to me, but after mowing for 20 minutes it...

Well actually my lawn tractor is a Statesman but its not on the list. AYP product. 20hp. Vanguard engine. 50 inch deck. Mower was purchased in 1994 and has had very heavy use over the years. The part that failed was the idler arm that operates the clutch/brake. It was rusted on the shoulder bolt...

My 2022 Troy Bilt Pony lawn tractor starts and runs fine. I can engage the mower deck with no problem. But whenever I release the parking brake and engage the clutch, the engine bogs down and eventually dies. Doesn't matter what speed is selected, where the throttle is set, or what gear is...

I have a HF 2147 ride on when cold the clutch engages immediately but after about an hour when i stop to empty the grass collector I stop the cutter but when i try to star it again it take 20 - 30 seconds to engage. Any ideas?

Hi all , Working on another Echo CS280E. I need to replace the clutch drum. Parts Tree says part number is 17500515330 of which is discontinued. Clutch drum says 91S ZY on it. Is there a superseded part number or an aftermarket clutch drum? Thanks , Matt.

The blade/PTO clutch won't engage. I've checked the connector on the PTO switch and there's a lot of corrosion on two contacts. Next step is to try jumping across those two wires with the switch in the on position. Does anyone know where I can view a schematic of the mower and the PTO switch?

Belt getting hot, checked all deck pullies spin freely, replaced tensioner spring, PTO engages wben pressed. Belt and pullies running but belt getting hot. Shut down and checked pto clutch is hot to touch. What is causing this?

Asking for help and advice if possible please. I have just replaced the electromagnetic clutch on my Scag Turf Runner as shown below and the space on the pulley for the vee-belt is wider on the new one than it was on the old one. It is only a few mm wider but it means that the belt sits lower...

I have ordered a new anti-rotation rubber for my Scag Turf Runner clutch (part No 20 in diagram below) Mine has partially disintegrated. I know where it all goes but just wondered if there are any special instructions when fastenening it to the rim of the clutch ? i.e. does the anchor point...

Hello I have the pilot bearing near the sheave gear go out. I have replace both pilot bearings and started mowing and the pto clutch started howling. Unit has 800 hrs . Which I think is bad. I have a new oem clutch, but asking the experts if I should buy the stub shaft and replace both at...