briggs

I have a craftsman mower with a briggs motor, 093j02-0011-f1, pouring white smoke out of the air filter breather tube. It is difficult to start as well. Any advice is greatly appreciated.

Where can I get a high-altitude main jet for the carburetor? Need 6000 to 8000 FT.

My son and I want to rebuild and older 5hp B&S flathead when he comes home from school. Any recommendations on suppliers? Model Type Code 130202 0801 01 80062307 Thank You

My 32 year old lawn tractor finally blew up and I am replacing the 12.5 hp Briggs that had no voltage regulator with a 28P777 0641 A1 14 hp Briggs that has a voltage regulator. 1) Do I simply hook the red wire on the regulator to power off the switch? It is a 2 wire voltage regulator if it...

Craftsman Model 917 270820 tractor with B&S 42E707 2631 E1 Engine Surging when idling - I can see the governor moving back and forth, but it will not idle smoothly - I can see the governor springs in there and it seems to not have any missing parts (like it threw a spring off), and all the...

Started some work last year on the motor on my L120, didn't keep track of the bolts to reattach the intake on both sides.... Grrr, just get a ziploc baggie... anyway everything is basically a 10mm head but a 1/4-20 bolt seems to fit really well. I'd like to keep everything oem but not if I...

I was just cleaning the carb on a B&S 100802-0121-H8 which I believe is a 750EX ReadyStart Victa Mustang mower engine, but the sticker has come off before I bought this. One of the linkages (governor?) disconnected and I can't see where to attach it back. It's probably not easy to explain, but...

Hi, I have a briggs 407677-0229-E1 (craftsman ride mower) It has had a valve bearing slip (over heating, mouse nest etc.) It bent two push rods. The real problem is that there seems to be a small crack in one of the valve guides. I can't seem to find the guides for sale; I know that they are not...

This is an engine on an older pressure washer. I have had it since new but it has not been run for about 10 years. I usually use Stabil when I know I will store an engine but dont recall if I did this time. The is a few tablespoons of gas that I poured out. I have not tried to start it but I'm...

Craftsman DT4000 Briggs & Stratton Intek 24 HP Model 445677- 0413-E4 TL/DR: After misdiagnosis of an internal engine rattle, I removed engine and opened crankcase to find nothing wrong inside. Motor has 600 hours. Has had regular oil and filter changes and air cleaner service. Has good...

Howdie to All out here lm from Canada 🇨🇦 SK wondering if any one had complete intake for one mine kinda !! Burt badly so don't want to bye new so lookin for used so any help would be awesome and if ya would like to donate for a wheelbarrow rat rod for my Son thks again for your understanding...

I have a Briggs Model 09p702-0144-f1. I am looking for the valve clearances with no luck. Anyone have them with in reach? Thanks , Matt.

I have a Briggs 19.5hp that had a bad camshaft in it, I replaced it and the mower would start fine when cold , harder to crank when hot. Now, it wont crank with a new 340cca battery and booster cables from the truck connected. Ive tried readjusting the valves (intake .005 exhaust .006), did not...

My tow behind tiller uses a B&S #13l332-0001 E8 engine. After two seasons use the engine lost spark and would not start. I disconnected the kill switch wires and still had no spark. I bought a new #590818 coil from a B&S dealer and set it up (this side out) at about .010" from the flywheel. No...

starts right up, will not kill when i turn the key no other wires go to the coil apart from the plug wire i found a red wire and a black wire that go under the flywheel, red wire lights up with key off and the goes off when key is turned on assuming yellow wire is kill wire and it turns into the...

My 15 year old walk behind 21 in snapper/Briggs blade clutch cable (the dead man switch- you let go of the bail on the handle and the engine stops) broke. the replacement part is called "Control Zone". Seems "Blade clutch cable would be better- stupid." . Who picked "control zone"?

Hi. I have a 12hp Briggs engine 281707-0173-01 for which I've purchased a B&S Carburetor Overhaul Kit 394698 . In this kit, there is a very small green plastic gromet, about 5 mm in diameter. Where does it go and which way up? It's the smallest item, bottom right in the attached photo. Is...

I have a 356447-0415-G1 horizontal V twin Briggs&Stratton engine on a Walker S18 mower. Sometimes the main pulley driving the mower from the engine does not spin. If I stop the mower and manually spin the main drive a little back/forth, and then restart the engine, it will spin. It appears like...

I am once again looking at log splitters in the 25-ton range. The few I'm looking at come with the engines mentioned in the title. I'm sure the exact engine models would help, but I don't have that info. Are Briggs engines still okay??? I've read some things over the few years that make me...

Can anyone tell me what these are for? (circled) This is my exact engine and application - 128M02-0423-F1 I bought a NOS Briggs and Stratton short block engine that included a gasket set. PS Since originally posting this I was able to figure out some of it. One is the intake manifold to...

Mine's still running fine at 170hrs but my question is: Is there anything I can to to pre-empt failure? I've read of a work around with the starter so you can keep using the engine IF the parts fall harmlessly in to the sump. But engine becomes junk if the parts hit other parts. I haven't seen...

Simplicity Regent 12 witha 12.5hp Briggs 289707 1 cylinder 4 stroke running incredibly rough, smoking, stuttering. On lower power settings it will smooth out for about 3-5 seconds then die, on high power settings it stutters and runs extremely rough, never smooths out. Has an integrated...

1.Model 31A607 Type 0741 E1 Code 070326ZE 15.5hp 2.Model 287707 Type 1224 E1 Code 971009ZO 14.5hp Unit #1 is a salvage mower that I swapped this 15.5hp engine into. Battery is new. Worked well until no crank, just a solenoid click. Swapped in a used solenoid and it started OK for a couple...

I built this log splitter about 25 years ago and it has split may tons of wood during that time. I changed the oil about a month ago and a few days ago I started it and it had a knock. I've started it several times and it knocks every time. The engine numbers are 252417 5526 01 and I assume this...

I'm looking for the torque tightening sequence pattern and torque pattern

Briggs & Stratton 8.50 H.P. Pressure Washer cranks & runs good for 30 minutes then dies, replaced the carb & the coil still have the same problem ?????????????

will start 1st time run great but shut it off it will not start. Also under a load from the wand it wants to bog down