Search results

Wow, didnt know that. Why did they decide that? What are they into now?

This one matches that #...

Thanks, IL. The engine plate shows ohv13-206820B (H). But are the #'s stamped on the starter itself useless (the 36914)? Why are they stamped on the starter?

Thanks, IL. I got 26 years out of it, not bad. But curious- do you think that would account for why I am getting only 6-7 v with started having been mounted on the mower? What would cause that? Now, where to buy a new one......There are 2 #'s listed on back of the starter- on top is the 36914...

People, MTD mower from 1998, tecumseh 13 HP engine. new battery, and voltage at starter shows only 6-7v but when red hot wire terminal is disconnected from the starter bolt it does show 12.7V, same as on battery terminal. So I removed the starter suspecting that was at fault and put it on the...

OK, heres what I got for readings so far, to start: Battery V is 12.1 (between the 2 posts). With key OFF: V between the 2 heavy terminals (not the SPADE connector that has the thin wire) 11.85V. With key ON: zero V Key OFF: between heavy left terminal and spade connector terminal zero V...

SN is 1C048C20044, , model 13A4667F118 MTD. Thanks, Star, for detailed follow up. It is starting to be clearer now. Will repeat tests and answer some of the questions you posted. Then go from there. It has cleared up now, trying to go out there again to do more tests............ PS: solenoid is...

It's raining today, so cant do any testing on the mower. But maybe Monday when the rain is over. I am a basic learner, struggling, with the help of any member offering here, much appreciated. But when it turns to uncalled for anger and resentment with accusations and criticism on top of that is...

But, Rivets, on my post #49, I said the 2 terminals on the solenoid. Am I missing something? There are only 2 main terminals (that connect to the heavy main wires) on that, the other is the spade post, to the very thin wire.

I have sanded down any possible oxidation on the terminals. Also, new copper hot wire on battery. With a new solenoid, where could there be the V drop?

Across the 2 terminals of the solenoid it reads around 3.5-4.0. Fluctuates. And on far side of solenoid (terminal on right side) to the spade connector with ignition on , 2.0V or so. At starter, key on, 4-5V or so. Something is messed up.

Thanks, Rivets. If I have just 12.14V on battery I have a bad battery? If I need 12.4, I understand, I probably have a weak battery. For starters! Should I even bother with all the other testing?

OK, wil do. Will need a helper for that. But if this helps- battery V with no load is 12.14.

So, if a test light that lights for 12v light up it does not mean you are getting 12V? Why do they call it a 12V test light? If I get a helper to turn the engine over and I test for V with meter I need at least 9V? I didnt know. That seems too low, no? A starter will turn over with just 9V?

Wow, so many post here that offer good info! Thanks. But UPDATE: I installed a new solenoid as well (after replacing the cable with new copper!). And mower still does not even turn over. I got a 12V test light and got a light on the IN of the solenoid, an OUT of the solenoid (with switch ON)...

But in the photos it is misssing the spade connector. My mower has the solenoid with a spade connector.

Yup, grounded by bolts, Im pretty sure. Thanks.

Good tips, people. You mean like this one here...

Thanks for all the many good tips, people. After the cable, I need to test out that useless solenoid that needs replacing every year. Sheesh.

Wow, good to know, people. Maybe thats why the mower wont start. Can anyone find such a cable on say, Amazon? Other? Thanks.

People, MTD mower turned over a bunch of time, weakly, and never started. So I cleaned off the corrosion from the positive battery cable and noticed the terminal on that red cable has ben reduced by corrosion over 26 years to about 1/2 the surface it originally had. Does this make a big...

Wow, that it! But 2 days ago I ended up ordering the one from Amazon. I got it and I have one question- there is no flow direction arrow on the filter. I blew into it both ways. Should I assume it can be mounted either direction?

Thanks, srcub! Yes, that makes sense. I do believe it is a 1/4" hose. Do you think this offering will do? It doesnt specify 1/4"...

People, Have a MTD rider, model 13A4667 F118 (model 667 for short) from 1998, with Tecumseh engine 13 HP. The manual diagrams list EVERYTHING but the fuel filter. I also looked at the tecumseh fold out pages, and nothing. Does anyone have an item/code # for my fuel filter based on above...

Wow, a year already!! I did install the new engine to variable speed pulley belt, a Stens. And wow, so much better! The other bely had only been replaced recently, so I didnt bother. BUT, Now, where before just about all speeds from 1-5 were sluggish, and 6 speed sent the mower speeding out of...

Whew, got it done. used a twisted steel cable, looped it and hooked it to the spring end. Then the other end of cable , I twisted it multiple times around a 1x2, and pulled like mad until the spring hooked! Undid the cable, and all set. I have done many maintenance tasks on this old mower but...

I will try the spring hook idea, have to make one first. What a job!

People, Have a MTD model 667. 1998. I replaced the deck belt and in the process I had to loosen the belt tension in order to pop on the belt to the main pulley, so I released that big tough spring that clips to the left side of the transmission bracket. I neglected to take note of where it...

So good to know as I never knew that. So, I will order both belts using both NEW #'s above. Will report back with results!

Thanks, but those #'s are not listed in my parts diagram. I show 754-0370 and 754-0280. But why does my speed #6 go fast as heck if my belts are old? One was replaced last year and I mow only about 8x per year.

Then there also TWO different variable speed belts. Which one? My MTD is model 13A4667 F118, if that helps. Thanks again.

What do they call transmission belts on the parts list? Drive belt? I do not see anything listed as transmission belt. I do see a V belt on the list.

MTD Rider, from 1998. Speed stick goes from 1-6. Lately any setting from 1-5 goes sooo slow, like never before. The difference between 1 and 5 is hardly noticeable, and when going up a slight hill the mower almost stops, until the ground levels out and mower speeds up a bit again. BUT when speed...

Got the new spindle shaft, it fit nicely. returned the defective ebay one. Tightened up the nut to 90 lbs with torque wrench. All went well. Big thanks to all here who helped me out with so many tips!

Wow, 95 lbs, never knew that. I always just tightened it up as best I could. I doubt it was 95 lbs. That is like the lug nut on my GM car!

Got the new shaft, and it fits nicely. Now, when I dry fit the new blade onto the bottom sprocket, then thread the old nut on it the nut bottoms out before masking a snug contact to the bottom of the blade. I dont ever remember there being a washer between nut and blade to take up the void space...

Wow, I didnt know! So, clicking the 1st site, I now learned I can buy just a shaft as the rest of the spindle is good, just the shaft is chewed up. I will call them tomorrow when they open and inquire how to buy one. I also will keep this link (and the other 3) for future reference. And thanks...

Good to know. Never knew that, and never had such a problem with ordering parts for my very old mower. also, if you provide parts and have a website for such shouldnt the supplier insist on a SN and model #? How sloppy. I still done understand. Even if parts are different doesnt that mean one...

618-0138. I am meticulous about records, and part #'s. That is also the # he advertised. Do we really need SN's? Never needed it in the past......

Old shaft is 5 7/8". new is 6 1/2".

Got the new spindle, and the length of the shaft is longer than my original one. Yet, on the site from the supplier the # matches the MTD #. Should I complain to the seller? Could this still work? I fear the different length will elevate the pulley higher, and the belt will not work right, or...

Good to know, people. I will let you know how it all ends soon........

People, MTD rider, bought a new spindle, and need to remove the pulley and put on the new one. I have an impact wrench with socket and wondering if anyone here ever had luck doing this as opposed to using an impact (air powered) wrench. Thanks, people.

So good to know, people. I cant wait to cut grass. (I spelled paint wrong!!) Anyway, another post coming in equipment. Thanks!

People, Got 2 new Oregon blades for my MTD mower. They are pained black with high gloss paint. And the edge doesnt seem sharp when I run my finger across it. Is this normal? Thanks.

Thanks, people, for so many good tips!! Wish me luck!

Thanks, but can you say what other way? I have time on my hands........ OOps, sorry for repeat post, I hit save too fast.

Thanks, but can you say what other way? I have time on my hands........

Have an old MTD rider mower needing new spindles, and last time I replaced one years ago I had a friend use a impact gun to remove the nut. Is that the only way to do this? Planning ahead, so I am prepared. Thanks, people.

Right- 1st mow in about 3 months. Yes, I have had this scare before, but wow- just finished mowing! Gears (pulleys) are working fine! Yipeeee! I think you are correct- have to jiggle/rock/move the seat/machine a bit to get tings to fall back in place. Anyway, Im sure I'll be back here soon with...