Search results

You are in a pickle, sadly. First rule=Never round off a bolt. I'm not going to get into questions about the proper tools, the damage is done. You will need to remove the transmission and your best bet is a machine shop. You can't heat it and you can't weld a tool into the hole, I know of no...

Does it happen when you first start it or only after using it for a while?

Agreed!

I believe you need to remove the engine's cover plate to change it. Very rare they leak/go bad on a Vanguard.

Sounds like the needle valve or jets in the carburetor or a restricted air filter. Don't buy a new Kohler carb until you, or a pro shop, tries to repair it. And DO NOT buy a non-OEM carb, it will not run correctly. The first thing I would do is try running it without the air filter. Next, check...

My 122 has a junk pto and am looking at a fully restored 147 hydro with hydro lift. Just trying to figure out if the the deck is the same hook up. Thanks a lot.

Costly mistake...should have left the handle out and dragged it. Better yet, pull the two releases on the hydro's and go very slowly. Probably a 3400 series hydro gear...ouch :(

Pat, respectfully, I recommend that you take the machine to a local small engine repair shop with a good reputation. Do not use that old gas, do not store gasoline in a glass jar. I am not going to be able to resolve the many issues you have with your level of knowledge. Please, bring it to a...

Okay, I had a closer look at your pics and saw several things that are incorrect. First, the wire coming out from top of the cylinder is the "hot" wire for the solenoid on the bottom of the carb and you have it connected to the stud. The black ground wire goes to where you inserted that threaded...

Fuel cap vent. Soak the fuel cap in some dish water and rinse well. next time it happens try loosening the cap and see if it fires up. alternately simply purchase the correct fuel cap from Toro dealer and be done with it. But first check to see if it fires up when you loosen the cap.

First, you need to purchase the OEM carburetor, not the cheapy Chinese ones that NEVER work correctly. I have no idea why they sell them; the reviews are all fake posted by employees or distributors. If you wish to fix it correctly, go to your nearest 'bota dealer and order the correct...

The issue with the electric mowers is if they fail, who is going to fix it? The two most common issues are battery and motor failure. The motors will overheat in heavy, thick grass and melt the windings. Good luck getting a new motor. However, no need to worry about gas and oil. Just the blade...

How about simply following the manufacturers recommendation in the owner's manual? They bench test them under full load for thousands of hours with various oils. The engineers that designed the engine are far better versed in which viscosity and spec will provide the longest life. You can't go...

Does that have a "mow in reverse" cut out switch? Just a thought.

Not on a 15 yr. old Honda. The engine must be fully disassembled. Tons of good used ones for sale on Criag's list and Facebook marketplace.

If both valves are closed there will be compression if the belt broke. But I agree that the flywheel may have slipped if something was hit solid. Hopefully that's the problem but he didnt mention a blade strike so I doubt it. If that was the case you would not have abnormal resistance when...

Hard to diag via text. However, my guess is the either the plastic overhead cam broke or the nylon timing belt broke. remove the valve cover and have a peak. It is quite easy to remove the cover.

I have two employees and we are busy year-round. You can research me here if you wish.

Of course, I always try to thoroughly clean the original with a strong solvent (Purple Power and Berryman's B-12) in an ultrasonic machine as well as manually when it comes out. I am 97% successful in doing so, however, sometimes you get one that's been sitting for years with bad fuel and...

My Pleasure. Not sure why you perceive 3200 as high, they are set from the factory between 3000 and 3200. The governor spring gets fatigued over time and may need an adjustment. I'm thinking once you get the blade balanced so that it runs smoothly you will get used to it. My only other thought...

Sure is, drive a 3" nail straight into a stud leaving about 2" exposed, wipe a bit of grease on it and it is a far more accurate balancer. It sounds fast because you're used to having it so low. 3200 is ideal.

The spec is 3100 to 3200 RPM's for a 21 or 22 walk behind. Those cone balancers are useless. Simply drive a large nail in the wall and wipe a bit of grease on it to balance. If it is a star hole, simply place a similar sized socket in the blade hole to balance. Balance is important on the long...

I pity your customers if you do such things. I fix them right, every time.

I suggest you find out for a fact. Take two coffee cups, place the diaphragms and the rest of the carb in the cups. Fill one with forty dollar a gallon "true fuel" and the other with pump gas and allow both to fully evaporate. let set for a week, repeat the process for a year and then see if...

Just use the Echo 2-stroke oil in the 2.6 oz. container mixed with .8 gallons as well as stabilizer. That canned fuel is a massive waste of money and no better than brand name pump gas. Use regular as it is more volatile than premium.

I have been in this business for 16 years. I have never had an engine run properly with a Chinese junk carburetor. All the reviews are BS. If the aftermarket came with a solenoid, you could try that but with the main jet from the junk carb, that was likely causing the surging so it may not work...

Hi Aplayeru, Many times difficult shifting is caused by the belt not fully releasing tension on the transmission pulley. Secondly, it can be caused by worn shifting forks inside the transmission caused by "forcing" the shifter or just simple wear. My first try to correct the issue would be to...

Their walk behind snowblowers are manufactured by Ariens'.

Owner/operator of Kevins Small Engine and Tractor Service located in South Berwick Me, 03908. I opened the shop to the public in 2008 in my 24x32 shop and the business exploded well beyond expectations. I hired an employee in 2010 and in 2014 I built a 30x60 addition to the building. I should...

Hi Just bought an LT160 Hydro and would really appreciate it if you could take the time to send me a copy. My email is kbowley@comcast.net

I have had three of those so-called "MTD Engines" come through my shop with identical symptoms; Very hard or no start, very low compression, worn rings with some bore wear. All three were replaced under warranty by Craftsman without questions or hassles. They sent me a new short block and I...