Search results

Your favored plug for the 500cc briggs is what? A good spark plug eases the strain on everything on the engine,starter,battery,me. :-D

Is this just another case of cost cutting,buyer be damned? Glazing the porcelain would add to the cost so why do it if the plug will last a season! As for me, I'm happy with my Briggs and Stratton branded spark plugs.

I was recommended this plug for my Briggs engines by a pro mower guy. He says it is way more resistant to carbon fouling and misfiring. He has a gang of summer workers that are NTB and will over-choke an engine until it starts to sputter and sputter and foul a regular copper plug. I have had no...

My local Lowes has this.48 Oz for $8.49+tx. Just the right amount for one full oil change.

" I am considered unAmerican , communist & even worse to some forums unchristian." Not in my book,bertsmobile1,you're more like your title under your name. ?

Sorry...I'll edit out my surprise at that price per quart. I have Prime, but still seems like a lot of $$$ to pour into a Briggs,though. This is for 4 quarts,my price.

Royal Purple straight 30w is over $13.00 a quart here an my local NAPA store Is there any real advantage of straight weight oil over the 15w40 I'm using now?

I see a problem in this pic,this guy isn't getting any of the monkeys to help! (they are a lazy bunch!) At least,the WWotW is getting one monkey to help and advise her.

Go with the fuzzy side up.

Air conditioner leak detection dye should be a good use here. It's made to go in lubricant oil. I am reminded of the rolling in flour and look for the wet spot ,looking for leaks. The dye is less messy.

$15.00 a gallon for the T6 Shell. Add another $10.00 for the full synthetic. I change according to Briggs recommendations, but usually sooner.

So...is this B&S oil a re-labeled oil made by a major oil maker such as what I have been using? I've been using Shell Rotella diesel in my non-cat sportscar and also for my small engines. Is this oil formulated for Briggs and to their specs?

I'd be using them for other stuff than cleaning a carb. Most all my carbs have way too small passages in them,except maybe my Carter VS.

It'd be worth that amount if only for those brushes!

Quoting the wonderful Roseanne Roseannadanna:..."It just goes to show you,It's always something!"

You missed my clarification...Not Series 11, Series 5.

It's not a 11 series, it's a Series 5,1984 vintage. New Rotary shifters are $18.00 free shipping. If I going to the effort to replace a lever,I'd prefer to go with new.

How about a shift lever for a 3311X5S RER? OEM part number is 7040284

Snow Globe,anyone?

I used that "covering the intake' hack,until I bought a new engine. However, as was pointed out here, there are broken pieces inside the engine that may not play nice with other parts in there. There are many 31R Briggs engines out there that have failed for different reasons besides the...

My mother-in-law has a n almost new Dodge Durango. Last snow,the 4wd wouldn't engage. Under warranty? Nope. The dealer said the shift motor was stuck because it was not engaged often enough.

You're not biased. I'd wager you'd be 100% correct. If anyone reading these posts were born down under,I wonder who'd opt to come above 0 degrees latitude?

Original Onans( from 16 years ago is a plus) were fine engines and to me,junking one would be a very last resort.

An engine not long for this world? I simply meant the engine may not last long in an application it's not meant for.

Sorta like 'The Deacon's Masterpiece'? :-D

Good catch,StarTech! I need to re look at the OP's pic. My mistake. Of course both sides of the loop go through the slot. I was concentrating on the Ground wire not the choke linkage :-(ashamed)

All my Briggs linkages look like this and there is no separate choke cable. When the throttle lever is moved to full wide open,the part of the linkage that is unseen in the posted pic,moves to push that loop of wire to the left (in the posted pic) to close the choke butterfly. Moving the...

I've held off as long as I could,but just can't help myself this morning. My "Winter" setting on my Poulan Pro 260 is "setting on the shelf in the garage"! LOL!

You should use stranded automotive wire,16 to 20 gauge. This kill switch wire doesn't carry much current. Solid copper wire has no use on anything that has any vibration to it. The shaking,even a little will fatigue the wire ,leading to breakage and circuit failure.

Lack of oil galled the crank and broke the rod,maybe?

Those pieces on the wires can sometimes be re-used if the 'christmas' tree part isn't too beat up. If they will not go back into the hole they came out of and hold securely they must be replaced,otherwise ruining the wires is a likely possibility. What I do in such cases is to use a zip tie on...

While I agree with most of the assessments on impacts, a QUALITY air impact will do everything needed to be done on lawn equipment and then some. Note I say 'quality' -impact wrench. This may be a moot point as they are disconiued but used ones are around. A Snap-On IM32 butterfly impact with...

That is a nice looking pulley! When one of my idler pulleys locked up,while waiting to receive the replacement,I toyed around with the failed one for just a very few minutes,dulling one drill bit on it. While I most likely had the tools to get it apart,I quickly saw that this was a fools errand...

Oh,I agree. I just meant it's a common pattern for a bit wider wheel,not a taller one,but wider may result in taller,too. Just being a bit careful in the turns will work for now.

Drilling those pulley rivets isn't an easy task,as some of them are heated and bradded down in one operation. This hardens and tempers the rivet as well as makes sure it is tight because of the metal shrinkage when the rivet cools. It's also much quicker (and quieter) than bashing them down...

My opinion ,along with other posters here, is to never bypass the safety switches because that's what they are for-safety. When I bought my CZ42175,the seat kill switch was disabled. In the unlikely event I turn my mower over, I want my mower to shut off. The same with the "no start in gear"...

Good idea there,hlw49. The CZ421 has 4 lugbolt hubs that are the same pattern as my HF trailer I use to haul it. Going to a larger tire/wheel shouldn't be much of a problem. Shoot,I could even use my trailer spare tires on the mower just to try this out. Releveling the deck would the work/issue...

Welcome! :-D

While I was looking for tire tread designs,I ran across this information on mower tires,from "gardentoolexpert.com". This looks like very good information and I simply can't wait to try it! LOL! (yeah,right!) This is a direct Copy and Paste from their website: "Did you know you can...

On the sloped part of my backyard, if it's been raining recently and the ground is somewhat wet, if I get too aggressive with the levers, I'll be spinning my drive wheels that are shod with turf tread tires like crazy. I can only imagine how the smooth tires would work for me, even though the...

I toyed with the idea of replacing my drive wheels on my ztr, but the cons vs the pros was way toward the cons, plus the $$$$ of them told me they were not a good idea. As for the lawn care pro, my thoughts were he'd be better off simply having conventional spare tires rather than having the...

I try to make wide turns if lawn space allows it. Other types of turns take more careful handling of the levers, I have to be careful not to pull the reversing side lever too far back, as the mower will spin that tire backward. My Turf Care CZ42175 is repowered with a 19hp B&S which is a tiny...

This is good news! As I have a similar generator with a Kawasaki engine I am relieved that issues CAN be resolved. A big thumbs up to you, Rivets for your success!!

Having the tools and being able to work on your own mower helps keep our mowers running long after the big box mowers are scrapped. It also keeps us from being prey to repair shops that only care about the $$$. The knowledge base here that we are blessed with is immense and from repair people...

Good point! My somewhat elderly (2005) CZ42175 zero turn Turf Care/Husqvarna was also sold as a Craftsman and as a Poulan mower. On the plus side,since almost none of the wear parts on it are proprietary, so I don't have to rely on Husqvarna for parts. The deck spindles, hydros, and the engine...

I have a PowerMate small genset that has a Kawasaki engine in it. I bought it from Northern Tool quite some time ago. As I remember,it was an extra cost upgrade over the Briggs standard engine. don't think it came with an engine section in the owner's manual,though. I need to thank...

My issue in regards to a shredded belt was a frozen/bad bearing in a flat side idler pulley. But this was on a high hours mower,not one almost new. Wrong belt routing would be more likely here.

Kill wire, I'd bet.

eBay,bertsmobile1. A lesson learned.

I have actually had one of these filters come apart at the seam! I think the two pieces are supposed to be sonic-welded,but one I had wasn't welded together. It was down stream of my fuel shut-off so no big deal.but I check every one now.