Search results

I think I would see if the piston is moving up and down

Did you by chance jump the seat switch? If so it will activate the fuel shut off solenoid and kill the battery in that length of time.

Post the 11 didget model no. can't get that model to come up

4.10 = refers to the width of the tire, measured in inches · 3.50 = refers to the distance from the outside edge of the tire to the outside edge of the rim, in ... Missing: 4.10/3.5x5 ‎| Show results with: 4.10/3.5x5 for small front tires

Black And Decker Stanley owns MTD CC Hustler

Sounds like a charging system problem

can't read the model no.

can't read the model no.

Yes you are right about the 1/4 past TDC never tried the one valve fully open and adjust the other one. I will have to try it on the next one I do.

milky looking oil means it had water in the hydro.

yes sea foam is some good stuff

Watch the video. Engine has to be on top dead center on the compression stroke to adjust the valves.

Bottom valve is intake top is exhaust. Clearance is .003 to .005 on intake and .005 to .007 exhaust.

What model mower is it and model type and code of engine.

can you find the model no. and post it so someone here might be able to recognize ithttps://www.ahupd.com/husqvarna-532185382?srsltid=AfmBOorlL1cOAu-WuC6lKkyhvm8GcAEJFoabnYMGCXQemavZTcmU1kzP

can you find the model no. and post it so someone here might be able to recognize it and match something up.

https://kawasakipower.com/kengine/3-TechService/Home/Serviceman/99924-2093-09-FR_FS_FX651V_691V_730V_English_eBook.pdf follow instructions on page 25 and 26

651-691- 730 are all the same block. as long as you have room for the air filter it will work and as long as the crank shaft is the same. 751-801- 850 are the same block 921-1000 are the same block. I have change several of the 651s over to the 730 engine. Like I said it is the same block. I...

Is it an OEM regulator or a knock off..

No That mower is the same mower I have which takes a 2006B84 which is a 87 inch belt if measured around the out side diamater of the belt. Motion drive belt is a 2006B41 Deck belt is a 2006B112. If you measure all B belts around the outside diamater it will measure 3 inches longer that the...

a styrafoam cup works just as well

first two numbers of the serial no. is the year it was made

I use regular 87 octane ethanol in mine and have never had a problem.

Yes a missing axle key will not let it pull. Yes it does have an axle key.

Check the steering damper

check theck the hub on that side and make sure the axle nut is not loose and sheard the axle key

I always replace them as a set. Not as fimiliar with the CH but the CV. First one I ever tore down with blown head gaskets I took one look at it and said it needs fire rings on the gasket. 20 years later they finally did it. Best indication of a blown head gasket is a fouled plug. Compression...

https://www.made-in-china.com/showroom/wszty18/product-detailNeknDsWKluch/China-25HP-Air-Cooled-Twin-Cylinder-Vertical-Shaft-Diesel-Engine.html

if you are not going to reuse the old drain just cut the tube off the drain. Loosen the lock ring screw the drain out and install the new drain hose. I never have to remove the engine or loosen it.

Nice mower regular service adjust the valves at 300 Hours. Keep it clean. Clean around and under the hydros, top and under the deck. Check the air pressure in the tires regularly a good tire on your car can loose 2 psi a month and these things are worse. Enjoy I'm jealious. I own 2 older Dixie...

Are you sure the bolt did not break off in the block?

Sounds like you just wanted an excuse to close up shop.

https://www.made-in-china.com/showroom/wszty18/product-detailNeknDsWKluch/China-25HP-Air-Cooled-Twin-Cylinder-Vertical-Shaft-Diesel-Engine.html?pv_id=1ijci90fk3b9&faw_id=1ijcialrkad3

Hi Steve welcome from north middle Tn. Lots of knowledgable people ready to help. Enjoy you time here,

Depends on the model mower you mowed with there some I don't like. But over all they are a good line of mower and will put them against anything out there.

Dixie Chopper never went out of business they were bought by Textron. Textron owned Jacbson and they built both mowers. Mechanicaly they were the same mower with diffrent trim package. They were then bought by Rhino Ag and are marketed under the Alimo group. It is a good mower,

I would never change out any of the hydro parts without changing the fluid and filters. I change the parts filters and fluids and flush the sytem to make sure I get all the metal shaving out of the system.

Don't have rocker arms it is not an over head valve head engine

You mean the people who make up the lies fact check their own lies. Boy that is getting to the truth of the matter.

Never ever take the screen out. It is a federal mandate. if you take it out and start a fire you are responsible for the damage it causes. They are too easy to clean to take out. Take a propane tourch and heat it red hot the hit it with compressed air and it will blow the carbon out.

302585 Dixie Chopper Spindle short. $156.84 These spindles are non-greasable.

It is such a shame back about 2012 because of the EPA emission standards. Generac instead of revamping their engines to meet the emissions standards they just kept leaning down the carb which made the engine run hot and caused it to pop the head off the exhaust valve. Then they and Dixie Chopper...

2011A65R Dixie Chopper motion drive belt. The adjustment is spring compressed to 3 inches. You can slide the engine if need be. There is also an adjustment on the deck belt.

We don't waste time trying to run down parts for that type of equipment. Do you charge for the time you waste looking up the parts and freight to get it to you. To us just not worth it. Red Max is or was a quality line of equipment.

Happy New Year to all hope you have a prosperious and happy new year

We don't work on them it is money wasted you can buy a better quality trimmer for a little more than it cost to fix it.

Have friend that has a CV25 Kohler that he swares has 8000 hours on it and still running. Have seen Generacs on Dixie Choppers built in the late 90's and used commercial and still running. No telling the hours on these engines. Briggs Vanguard is an excelent engine as well.

Buy the xtreme best clutch going. Been using them for ten years of so and have never replaced one yet.

wow my moto is if I can't pay for it I won't buy it.

post the model no. under the seat