Search results

Hi Guys, Fired up the above captioned mower for the first time this season yesterday. Decided to put on a de-thatching blade so removed the regular blade which seemed secure. When it came to installing the thatching blade I noticed the bolt would not tighten and was threading in a little off...

A friend has the above captioned mower which I borrowed. I tried to start it but the engine would not turn over....checked the battery and it needed a charge....down to about 8v. I charged it overnight and it reads 12.8v on a tester, but it only turned the engine over about three times and then...

Hi Guys, Toro 22" self propelled mower seems to run fine, but has constant light blue smoke from exhaust...checked oil and it's right on the "Full" mark. I suspect a ring problem, and if this is the case can it be fixed, or is it cheaper to replace the motor? Thanks for any help. BTW...this...

Hi guys, I have an older R70 rear engine lawn tractor that I've just got running with help from this forum. My question is should I change the oil in the gear case as I'm sure it has not been done for many years, and if so, where are the drain and fill plugs located? I have looked at a...

Sorry....missed sending the second photo.

Hi Folks, Apologies if this is not in the right forum....I looked for Husqvarna but couldn't find it. Anyhow, I have an older 25R trimmer that's been running fine for 20 odd years. Suddenly today I started it up, and it runs at idle , but as soon as I apply throttle it dies. I re started it and...

Hello all, Have a very old John Deere rear engine mount R70 tractor/mower. It fires up so has spark....it has fresh fuel...gas lines and in-line filter are clean. Here's the problem.....it fires right up, runs for 10-15 secs and then dies. There is a pilot screw at the bottom of the float...

Hello all, Have a very old John Deere rear engine mount R70 tractor/mower. It fires up so has spark....it has fresh fuel...gas lines and in-line filter are clean. Here's the problem.....it fires right up, runs for 10-15 secs and then dies. There is a pilot screw at the bottom of the float...

Further update....new battery hooked up....same problem....whirring noise when key turned on. Power between the two positive red cables in and out of the solenoid reads 13.2 both sides...have to wait for the wife to test the voltage between the small wires on the solenoid. Have attached...

Hi ....I have a LTH 130 that I'm in the process of getting to run. The mower is in good condition, but after a few minutes running it will not power up even the slightest incline. I have been told that this may be due to the hydrostatic pump, or even just a change of hydraulic oil would solve...

Hi, I have a craftsman wheeled trimmer model number 944.361064 with a B+S 6hp motor. The belt kept coming off so I took the mower apart and found that the bearing seems to have come out of the housing....see pic. My question is can I re-use this bearing and press it back in, or should I...

Hi, I have a craftsman wheeled trimmer model number 944.361064 with a B+S 6hp motor. The belt kept coming off so I took the mower apart and found that the bearing seems to have come out of the housing....see pic. My question is can I re-use this bearing and press it back in, or should I replace...

Hi guys, Just mowing my lawn when the blade came loose...tried to tighten it but the crank is turning before it gets tight...any idea how to resolve this? Thanks.

Can anyone tell me what happened here? Was mowing and working fine and suddenly the drive to the rear wheels quit. Could this mean a belt issue or??? Thanks for any help

I have the above mower for which I need to order parts, but I can find noi model number on the unit. The engine serial number is 126T05-0219 B1 07092757 Mower was purchased 2009/10 Need a schematic to order parts...can anyone help? Thank you

Thanks Rivetts....unfortunately I have done all you suggested, new needle and seat, carb. cleaner and air,new plug, re -assembled and still will not start. There is a small fuel leak out of one side of the carb...at the bottom as you look at it it seems to be weeping out of the hole marked in...

I have a Toro 22" rear drive Recycler with a Briggs 6.75 motor (190cc). Winterised (stabaliser in fuel), electric start battery fully charged, fresh gas put in, new plug, have spark......STILL won't start by key or pull start ( have even tried engine start spray). When plug is removed after only...

Hello, I have a Toro 22" personal pace electric start mower that's about 4 years old. This year it's been a bear to start every time I use it, and the electric start turns the motor over but won't start it. battery is good, gas is fresh, air filter is clean and I've put in a new plug....still...

Hi all, have a three year old Toro recycler personal pace mower that suddenly will not start either by key or pull cord. Could someone tell me how to troubleshoot this issue? Fresh gas, oil is good, spark is good...ran yesterday for an hour and then quit.(B and S 6.75 190 cc engine) Thanks

Hi all, have a three year old Toro recycler personal pace mower that suddenly will not start either by key or pull cord. Could someone tell me how to troubleshoot this issue? Fresh gas, oil is good, spark is good...ran yesterday for an hour and then quit.(B and S 6.75 190 cc engine) Thanks

Hi everyone, last year with a lot of excellent help and advice from this forum, I took apart and cleaned the carb on this mower. I also resolved the broken nipple on the gas tank which seemed to be causing my initial problem. The mower runs and cuts fine, but periodically revs up and puffs out a...

Hi all, Have a very old Toro 21" rear bagger Model number 26623. It's not been running well, and today quit completely amid lots of smoke! It's not seized, there is oil in the crank case, and it will start and run for a short period of time after a shot of carb cleaner. I took off the fuel lines...

I have an old (probably at least 20 years) Toro 21" self propelled mower for which I need a parts diagram. I cannot find any serial or model numbers anywhere on the mower, and I need to replace the bolt that holds the height adjuster to the deck. Anyone any ideas? Thanks.