Search results

I posted bar/chain and sprocket numbers above. Should the sprocket at the end of the bar (7) have same number of teeth as the drive sprocket (6). Should there be any end float on the drive sprocket when assembled and torqued correctly? Why will only walk off the sprocket when rolled backwards...

Bert its very hard to know what in your reply is true/fake/junk? So if I shouldn,t buy on amazon and the oregon parts are fake at ace/lowes/home depot where do you suggest I buy? The drum came in a Husqavarna package as well as the large washer. The needle brg, is installed and looks ok. I...

The bar/chain assy is Trilink PN BM 1501862-1041TL2 18 inch 62 DL 3/8 LP-.050 I think that is correct. I thru old clutch drum away so I caHELPn,t match to the new one. It has 6 teeth and stamped on the teeth is CS 16??? . I really don,t know what item is incorrect if any and can,t figure...

I just replaced the clutch drum and clutch large washer. Installed new bar and chain. I have done this at least 3 other times. Cleaed saw replaced fuel filter and all fuel lines and primer.. Th saw starts and runs but bogs down like a binding. I noticed after bar chain it won,t roll chain...

Correct won,t Rev unless you pump the throttle.. When you finally get it up to rpm it runs and and does great. I have previously changed plug fuel filter exhaust screen and it changed nothing. Once again I tried to adjust screws but not any change. Thats when I removed carb and rmoved red caps...

What are the initial settings L/H for the needle screws. I removed the caps and found low at 1 1/2 and the High at 3. Could that be a reason that it won,t rev when you ask for power/throttle response?

Carb P.N. there any real difference between WT-829 A021001330 and A02100331 other than 20$ in price? Thanks Jim

This saw never did respond quickly to throttle opening. It starts easily ,idles well, cuts good, but now its worse than ever getting up to working rpm, without at least 5/6 squezzes of the trigger. I have replaced the fuel,air filter. The plug is tan color (Help)

My deck doesn,t seem to raise very high. The Handle seems to have a lot of no response movement before deck moves/ Deck wheels drag at times at full up position

The lift shaft bushings have very minimal wear. The lever goes past the half way point before deck moves. I live rural so I need a higher cutting plain. The machine has 118 hrs . I still need some ideas?

Deck lever travels excessively before deck rises? Is there a adjustment for this or rigging procedure?

Sorry , I started feeling bad and stopped. It all came down to a poorly support bearing for the pto lever. I sandwiched a piece of 1/8 steel and a split collar brg. and a couple of good nylon bushings. Now the bearing/rotion suface is about 2.5 inches instead of that 5/8 split plastic...

Well I finally got around to working on the mower. Italked earlier about the engage handle. I remived the handle

Well I,m still looking for my non engagement of my mower pto. I looked at the deck with the PTO lever engaged. The belt was still LOOSE. I reached in and moved the lever/Idler pulley approximately 2 inches and that tightened the Belt. As I said before the deck levers move freely and lubed, it...

My LTX 1040 Single cyl Kohler That runs extremely has developed a fuel drip at the Carburator. Its hard for me to get down that low but it feels like its coming from a solenoid on the bowl.hould I buy a solenoid or is there a gasket/oring/crush washer in that system.If I close the fuel shut off...

My pto handle is difficult for wife to move to engage but why doesn,t it return all the way back or is not necessary. They disengage fine but still need more travel at the deck lever for a less slip engage. Has anyone added some washers/shims behing the cable ferrul on the deck or maybe a...

Bought a new OEM belt and 2 idlers. Removed all levers and springs, no excessive wear. Dry Lubed and installed deck. Performed much better, but why does the rpm change with deck handle up/down. Why is the deck belt a A sec. . when the pulleys are wide like the other belts on the machine 5/8 wide.

It might start but won,t stay running. Removed tank n cleaned replaced lines and filter. still the same. Replaced fuel primer, seemed like the bulb was loosing its mojo.,. I then removed carb WTA-28 Dissasembled (looked clean but let soaked 24 hours in carb cleaner. Removed from cleaner and...

My LTX 1040 that I bought from neighbor as the second owner. Its 1 cyl with 42 inch deck . I,m having issues with pto engagement especially when I move height lever. I was looking under the tractor and noticed that both arms were factory stamped with the number 38?????? could this be the...

My LTX 1040 that I bought from neighbor as the second owner. Its 1 cyl with 42 inch deck . I,m having issues with pto engagement especially when I move height lever. I was looking under the tractor and noticed that both arms were factory stamped with the number 38?????? could this be the...