Search results

Results 351 to 400 of 500
  1. B

    PTO problem

    Make sure you don't have a bad or binding deck pully first , if that's free pull the belt off the pto and engage while watching it spin / or not and see how the engine reacts. There could be a safety switch shorting out or some such.
  2. B

    128L05 0116 F1 Briggs motor struggling.

    You probably still have a dirty carb which comes from a dirty fuel system , tank, fuel lines, filter etc. if the carb was dirty at first and the tank and fuel supply system wasn't cleaned up too ,it got contaminated again I'd say
  3. B

    Z Force 50 not charging the battery

    Stator is either bad or dirty, clean up really well try again and make sure your meter is on the right scale when testing
  4. B

    Mower dies when engaging blades

    I've never seen this but if you can spin your deck by hand - I would spin each one individually and see how it sounds and feels - you can tell if one is dragging or not. But having said that and you're confident there is nothing binding there, pull your PTO wires off and run a separate 12vt...
  5. B

    Mower dies when engaging blades

    Is there a deck spindle binding up or a bad bearing somewhere ?
  6. B

    Z Force 50 not charging the battery

    DC voltage should be around 14 I think, Don't think it normally fluctuates but needs nearly full throttle to be up there. There are some good videos on Utube for testing the voltage.
  7. B

    Bad Breather

    Well if it's running at all the flywheel key is not a problem, sounds like you're moving in the right direction , only runs at low rpm if the linkage is moving the throttle plate then you probably have a carb problem.
  8. B

    Bad Breather

    Pull your breather and see if the problem persists
  9. B

    Spartan keypad issues

    I think I've read on here there are conversion kits to get around this keypad garbage
  10. B

    John Deere 115 mower - Briggs Engine

    Sounds like a fuel supply issue start at the tank and work back to carb , filter - hoses- pump etc
  11. B

    New plug, coil, and carb but no start

    I've gotten a number of carbs off Amazon and most have fit the bill just fine, maybe just been lucky but having said that just because you swapped the carb does not mean you've eliminated the carb as an issue.
  12. B

    New plug, coil, and carb but no start

    You can pull everything off the top, expose and remove the nut, an impact is best but get it off and look at the keyway, you should be able to see if it's off the fit. Does not take much for the timing to be off and will not run as such, This can happen via a backfire or hitting something while...
  13. B

    New plug, coil, and carb but no start

    Pull the plug and turn it over with the plug grounded , it should be really easy to spin and you can watch for a tiny spark at the plug. If it has a spark, re install and give it a squirt of starting fluid in the air cleaner and try and start, if it still a no go, you'll need to check the...
  14. B

    New plug, coil, and carb but no start

    You're goin to need to give us more information to go on like when was the last time it ran, what has changed since it was running etc. Just a little history would help us trouble shoot better
  15. B

    John Deere 757 zero turn - Ignition Problem identified.

    check your fuel pump , might be some debris in the valves stopping it from operating like it should , there are 2 small check valves and most are not repairable.
  16. B

    Toro mower 20333 very loud

    When did it start doin this ? Was anything changed ?
  17. B

    Husqvarna LGT2554 boggs down when blades engage.

    I think they recommend revving up to full throttle before engaging the blades then you can regulate back to slower speed after the governor kicks in
  18. B

    Murray mod# 42598X92,Electrical Problems

    It sounds like you have a safety switch acting up Might try and bypass one at a time and see if you can isolate where it is
  19. B

    LT 155 blade spindle alignment

    Re set the timing and install new blades , if the spindles turn and feel smooth they're probably ok I've never seen this set up but after installing the new blades spin by hand and see how it looks then run it and test the cutting - if it looks ok , I'd say run it .
  20. B

    2021 MZ Magnum 54 won't start and battery cables are hot

    It should disengage when the machine starts , the momentum of the ring gear should shoot it back down to it's normal position, I had one that didn't disengage once and drug the motor down b/c it kept it in a bind , you can pull it and lube it up real good and make sure the springs are in tact...
  21. B

    Flywheel Ring Gear Bad 16HP Vanguard Briggs

    Back the nut off to where it's even with the flywheel Shaft, put pressure on 2 points 180 degrees apart and pop the top of the nut/ shaft with a good ball pene hammer and it's going to pop off. No puller necessary , I've taken off so many like this I loose count
  22. B

    2021 MZ Magnum 54 won't start and battery cables are hot

    Hot cable ends indicate bad connection , clean that up first and test the battery to make sure it's the right CCA and look at those connections as well as the ends at the starter and grnd. If all those are tested good , pull the starter and bench test it - does not sound like your solenoid to...
  23. B

    Flywheel Ring Gear Bad 16HP Vanguard Briggs

    Yeah I think the flywheel and ring gear are together - Look at Amazon and / or Ebay for a used flywheel or replacement for that model , short of that it would be someone who works on these and has some old parts /engines laying around. Odd that it is only 4 months old and the starter teeth are...
  24. B

    Fuel Shut Off

    Never seen a fuel supply come from the top of the tank , you may be looking at a return line
  25. B

    Fuel Shut Off

    Ohh Yeah with any type of fuel pump
  26. B

    Fuel Shut Off

    Are you looking at a manual valve ? If so I would put it before the filter so you can change filter out without loosing fuel, your carb bowl probably has an automatic fuel shut off for when you kill the engine.
  27. B

    Model 28 Vertical - No Compression

    Usually a tiny hole right on the same lever the larger rod fits onto .
  28. B

    Starter problem

    Hook up Jumper cables to a hot battery and see how it reacts
  29. B

    Starter problem

    You have done everything I would have - Don't rule out you have replaced a component that is still the problem.
  30. B

    Model 28 Vertical - No Compression

    I always use Permatex Gasket sealer on one side , Don't put anything on it until you are ready to put the 2 halves together, Use sealer or whatever you like only on one side in case you need to take it apart again , the gasket will hold and you should be able to re use it not having to scrape it...
  31. B

    Model 28 Vertical - No Compression

    If they're all the same you got some spares , you don't need more than one, Sometimes they'll put several different types to fit a various assortment of engines
  32. B

    Husqvarna will crank but won't Start.

    If it does not hit when using starting fluid it would seem to be ignition - if you have spark you'll need to look at the timing - maybe sheared the keyway on your flywheel - it does not take much. Did he hit something hard while mowing ? Hold your finger in the spark plug hole while cranking it...
  33. B

    New guy with beginner questions. Is there a oil drain plug or do i need to tip mower to drain ( Husqvarna awd self propelled walk behind )

    I've seen both a drain plug and having to tip the mower over, if there's a plug it will be on the base or underneath the machine , doesn't hold much so it's pretty easy.
  34. B

    Husqvarna YTH 2242 T choked halfway to run

    If you having to run it with the choke you're starving for fuel , look at your carb first
  35. B

    Charging system

    Most times you need to rev it up almost full throttle when engaging the clutch , then you can moderate your speed to where you want it
  36. B

    SD Blades Level

    Park the machine on a level surface and measure each side's ground clearance - if it's 1/4" or thereabouts I would not worry about it - as for leaving strips of unmowed grass That would not have anything to do with a level / unlevel deck - How old are your blades ? they tend to wear on the...
  37. B

    briggs and stratton 25hp valve cover not heating up evenly

    Well it wouldn't be running if he dropped a push rod or a valve
  38. B

    54" outlaw blades (aftermarket)

    I got a set off Amazon and they worked fine
  39. B

    briggs and stratton 25hp valve cover not heating up evenly

    The exhaust side will be hot but not the intake - Never really checked valve cover temps on any engine, On large industrial engines if you felt the intake was hot it told me I had a burnt valve
  40. B

    Troy Bilt 30 electrical

    Put 12 volts on the solenoid and see if it engages, Just clicking like you say sounds like a bad battery connection You can Jump across the larger terminals on the solenoid - if the starter reacts to that you know the starter is good but solenoid is not. Lots of the machine have extra wiring...
  41. B

    No safety switches working !

    I've rewired a few machines and did away with all the safeties but that's me
  42. B

    Flywheel Will Not Come Off!

    I usually drive a couple of chizles at 90 degrees apart then hit the top of the crankshaft with a 2 lb ball pene hammer a good lick and it pops up for me - Do that and apply a little heat if it does not pop up for you
  43. B

    Will spread grass blades over grass helps lawn or just bagging them is good?

    Depends on how thick the cut grass is , real thick will cause dead spots where it sits or lays. thinner stuff just sorta goes away and doesn't really hurt anything , I only rake and gather mine when it's really thick.
  44. B

    Suddenly running Rough and Stalling

    If it's firing and starting up - it's not your coil in my opinion, I think you have a fuel issue somewhere , coils either fire or not , fuel problems however behave like you're describing
  45. B

    Model 28 Vertical - No Compression

    Looks like you got lucky - a new rod might just be all you need along with gaskets etc.
  46. B

    Model 28 Vertical - No Compression

    Make sure your crankcase isn't damaged. Valves maybe bent and head could be scored up too
  47. B

    Dixie Chopper Yanmar Diesel dies

    Might look at a possible safety switch shutting you down - if it is doing the same thing after you worked on the fuel system - either you still have a fuel delivery issue or a safety switch is shorting out - I think if it was fuel you would see and notice a bad running machine before falling on...
  48. B

    2023 Briggs & Stratton XR 13.5 - Bubbles in fuel...

    It ain't the heat , it's hot everywhere - I've had over 100 degrees for 20+ days here and not seen anything like what you're describing and no one else is having this issue, it's something else in my opinion - Neve have I heard of gasoline boiling in a fuel tank
  49. B

    STX38 Black Deck Hydro Fan Replacement - Do you have to drop the trans?

    Not sure about that model but most likely you'll need to drop the hydro low enough to work the fan off, I know on mine and most I've see there is barely enough room to work the belt on
  50. B

    Carborator keeps flooding

    replace the carb or rebuild it, your needle valve is leaking
Back
Top