Search results

Results 451 to 500 of 500
  1. B

    Troy-Bilt WC33 engine question

    A ticking sound would suggest something loose being effected by the fan,
  2. B

    How to replace seat switch on JD 727A Ztrak mower

    Safety switches typically turn out of the fit 45 degrees or so and pull from the bottom , the seat itself does not need to be messed with , might want to post some pics
  3. B

    Troy-Bilt WC33 engine question

    Not sure what a WC 33 engine is but a Tick is not anything to stress over , A knock however is a real concern
  4. B

    Riding mower noise, pulley/spindle

    If it's a pully problem it would be constant , sounds like a belt slipping, pull the belt and roll each pully by hand and see if anything feels rough or noisy. Inspect the belt also to see if you can tell if it's slipping - it would be sorta shiny and stiff and not flexible
  5. B

    Looking for a problem free 42" Zero Turn Mower

    None are problem free - I've run Badboy for a while now and only had normal issues - I don't recommend getting anything with electronic fuel injected systems - anytime is has a problem it will need to go back to dealership. Just my 2cts.
  6. B

    Oops! Hit bottom and blades won’t engage

    What exactly are you saying " wont fully engage " ? If it's an electric PTO - it either engages or not - is yours a manual lever type that you engage ?
  7. B

    Just got Bad Boy Avenger 60 inch deck

    Been running a 54" Bad Boy for last 10 years - no complaints
  8. B

    Honda HRR216K9VKA dies after 15 minutes

    I've gotten new carburators that didn't work well in the past, it's rare but still happens - you surely still have a fuel supply issue or carburation - I know if's frustrating but keep at it
  9. B

    husqvarana rz4623 will not start

    You need to verify the ignition circuit is working, if this happened after your engine swap something is amiss in the wiring - use a test light and verify the switch is working properly
  10. B

    Engine dies when I engage the blades???

    Sounds like a safety switch , you'll need to bypass at least the blade engagement switch -
  11. B

    Vintage 3.5hp Briggs and Stratton 148cc Engine won't go past idle

    If the carb was sitting up that long - not sure you can clean it well enough also the soft goods are probably shot. If it idles the engine evidently is in good shape so it's most likely fuel issues - don't think that model has a fuel pump only the pulse off the crankcase working the diaphram...
  12. B

    The frozen whelk thread

    Make sure it's not a LH threaded bolt
  13. B

    Mustang XP PTO issues

    Sounds like your electric clutch is goin out - Never had one fail before but I'm sure it happens. Can't imagine what else it could be
  14. B

    Starter Problem

    That's only for the ignition system - most are built into the flywheel- the " coil " is adjustable and should have a small airgap that reacts to the magnet on the flywheel and creates the spark and also helps charge the battery.
  15. B

    Craftsman lt2000 won't engage the mower

    Is it an electric clutch / pto or mechanical shift to engage the blades ?
  16. B

    Starter Problem

    Not sure where the magnet is that you're speaking about but never seen a magnet involved in a starter bendix The bendix should engage when the starter spins up - there is probably a spiral on the starter shaft that makes it travel up to the flywheel then a spring to return it to it's original...
  17. B

    All belts blew a once

    Little you can do except change them out again, when all the belts are off look at all the spindle bearings - spin each one and see if any sound rough or have slack. See if they're tracking properly and go again. Never seen them all go at once but you never know.
  18. B

    Dixie Chopper 2017 Blackhawk HP Kohler Engine Oil Seal Leaking :(

    You can remove the seal pretty much any way you want , it's no longer being used so don't worry about destroying it in the process, I've pulled many by punching a sharp screwdriver or something and prying it out of the fit. Be sure and dress the whole area / shaft and seal fit with emory cloth...
  19. B

    All belts blew a once

    Did it just throw them off the fit or are they all destroyed ?
  20. B

    Honda HRR216K9VKA dies after 15 minutes

    I had a similar machine and had to drill a vent hole in the fuel cap. Also make sure your oil level is good, might be shutting it down when it's running via the low oil safety switch
  21. B

    Buying a used Honda HRX217 & motor issues

    I've found there are a lot o small gas engines that will " humt "with no load - it will usually settle down with the load applied.
  22. B

    Kohler turns over. Won’t start.

    Fuel for sure, pull and clean the carb really good - might pour a little into the carb and try it, probably will run for a bit before dying - float maybe hung up
  23. B

    Strange symtoms on 17hp

    Carb
  24. B

    I made a big mistake...

    It's Done - Get another same model , salvage all the usable parts of the first one and you'll have back up parts for the new, If I don't see blue smoke from the exhaust on a 2 cycle , I use more oil in the mix.
  25. B

    Toro ss5000 will not start

    What's the history on this machine ? Has it been giving problems starting prior ?
  26. B

    SOLVED 917.271532 runs for 30 minutes then dies. Starts right up after 15 minutes. No click in between.

    He stated No Click when trying to start so thinking it's the Starter Solenoid
  27. B

    725D PTO clutch not engaging

    put a volt meter on the wires when you engage the switch, Repeat with the engine running and wires off the clutch. Could be a bad or corroded connection or wires
  28. B

    Snapper series 8 model 28108e does no charge, should it?

    Should read close to 14volts , you need to look at the wires from magneto to voltage regulator - should read 30 plus into the Voltage regulator , from there should read around 14 volts to the battery. There is a procedure on Utube to lay it out for you if you do a search.
  29. B

    SOLVED 917.271532 runs for 30 minutes then dies. Starts right up after 15 minutes. No click in between.

    Next time it does it , bypass the solenoid and see if it hits. If so, it ain't your solenoid
  30. B

    kawasaki motor runs then stalls

    Doubt it's your shut off valve, probably trash in the fuel line / tank - blow back through the line - look in the tank with a flashlight .
  31. B

    What should I replace my Kohler Courage 25 twin with????

    Yep, that's what I found when I tore into one.
  32. B

    What should I replace my Kohler Courage 25 twin with????

    I think that model courage is badly designed , something came apart internally - that's what happened to the one I had - did a little digging and found out it was common with that motor to fail like this
  33. B

    Kohler M12 won't go over an idle

    Linkage ?
  34. B

    What should I replace my Kohler Courage 25 twin with????

    Anything close that has the same bolt hole footprint should work , I've used Kawasaki to replace a kohler before and it worked well, you will need the same sized diameter Crankshaft for the clutch and make sure the exhaust will have enough room to sit in that spot.
  35. B

    Spindle bearings

    Pull the belt off the deck and see how they feel and sound when turning by hand , should be smooth with no noise , if you feel or hear grinding noise - there's your problem 20 hrs is not very much run time on bearings sealed or other. Check each spindle - I've replaced complete spindles and the...
  36. B

    LT1042: swallowed up hammock strap, PTO won't engage

    I think there's a " pigtail" connection available with the OEM connector but I've used a couple of female spade connectors before with good results
  37. B

    Metal clank from 2042LS

    Well if it comes and goes it's not a major part like crankshaft / rod etc. BC that sort of problem will not come and go The fact that it's not constant is hard to pin point. Post a couple of pics maybe so we can get a better idea of what you're hearing - Does it sound like it's at the top of the...
  38. B

    LT1042: swallowed up hammock strap, PTO won't engage

    Your P TO wires probably got dislodged , if not there's most probably a fuse could be blown , put a test light on the PTO wires at the clutch and engage the clutch - doesn't have to be running you should see the light come on if not work back towards the switch / fuse etc. - there is also a...
  39. B

    Geez, This Is New. Has Me Baffled.

    Usually safety switches will keep the machine from engaging the starter. Why let the starter turn over and interrupt the ignition ? Cub may be different though
  40. B

    Geez, This Is New. Has Me Baffled.

    Spark plugs rarely go out , a fouled plug will look like new sort of shiny , a firing plug will be a bit gray and dry older plugs my look a little black but if they're firing the electrode will be dry and gray looking , Pull the plug hook the wire up and ground the threaded area while spinning...
  41. B

    Kawasaki FH451V AS06 governor air vane

    It is part of the Governor system and you need a replacement or your machine will run away. Someone here will find a parts diagram almost for sure .
  42. B

    Just a blown head gasket or worse ?

    If there's no compression the head gasket is the least of your problems
  43. B

    Weird One... Seized Kohler 7000 KT730-3046

    I ran into something similar with a Honda machine, if it stops in exactly BDC the rod didn't want to break over - after forcing it to move off that spot- it's all good. Sounds like the same issue
  44. B

    Kohler courage sv620s 210

    These machines are poorly designed in my opinion- I've seen this too many times and usually not worth repairing, Replaced mine with a 23hp kawasiki - had to get creative with exhaust and clutch but it worked out fine - I think the footprint was the same
  45. B

    SOLVED: NOT INTERESTED IN WARRANTY ADVISE-27hp 49T877 V-twin rod bearing oil

    Drillin a Crankshaft might be a little tougher than it looks
  46. B

    SOLVED: NOT INTERESTED IN WARRANTY ADVISE-27hp 49T877 V-twin rod bearing oil

    Wow , unbelievable - looks like you're goin to have to replace the crankshaft - that's the kinda luck I usually have - I'd be interested in how you move forward from this debacle -
  47. B

    SOLVED: NOT INTERESTED IN WARRANTY ADVISE-27hp 49T877 V-twin rod bearing oil

    Wouldn't surprise me if they're not cross drilled in todays age of quality control. If it's got an oil pump it has to be a pressurized system and getting oil though the crankshaft ports up to the rod bearings all the way up into the piston pin. Only way to verify is to pull it apart though
  48. B

    key substitute

    Don't see how a standard Key will fit where a half moon key goes or how to get it to stay in place. you should be able to find a " Key set " somewhere with the right key, I'd be surprised if you don't continue to have problems with this set up.
  49. B

    Slow to start

    Pull your starter and throw 12 volts on it , it should spin over freely , hold on tight b/c it will jump.
Back
Top