Search results

Results 51 to 100 of 500
  1. F

    Fuel line in a fuel line.... fuel filter?

    Why not just blow some air backwards through the fuel hose to back flush and re-install?
  2. F

    Troybilt Pony 13AN689G766

    V-BELTS now days. I most generally always measure a new belts length BEFORE I install and compare it to the intended specs NEW for length. I learned to do this the hard way. (school of hard knocks and money and time leaving my pocket and not coming back) Also I measure the old belt length if it...
  3. F

    Troybilt Pony 13AN689G766

    Hard to tell in the picture but seems to be about normal. Some things I've seen on that type deck from experience. I also noticed in your picture that is the type deck that when you raise it up all the way the top of both spindle pulleys contact blade brakes (item 32 in your parts list) mounted...
  4. F

    Broken bolt condundrum

    2nd type is little better. Got to remember that those type extractors will EXPAND the stuck stud and make it get tighter as it's turned as the sides of the stuck stud are thinned. Sometimes like mentioned in post #5 you can ALSO drill a hole into the twisted off stud, weld on a additional...
  5. F

    Booting lawn mower tires

    Right about rubber cement no good for such. I've almost had to use a boot few times on good lawn tractor tires that got stobbed.. (but got by without) I have some old tire boots that are no longer sticky set back for such as what you are doing. I've not tried such but have thought about trying...
  6. F

    Troybilt Pony 13AN689G766

    Keep a heads up when around that type machine when off the machine with it running. It's the type that the blades will start turning with the deck lever all the way up. Why: As the belt sets in one place on the engine pulley it gets warm/hot and friction increases and the blades start turning...
  7. F

    Compression Tester

    I also found that the CP7828A with all the adapters is a good go to tester. I also have couple homemade types that are accurate buy usually reach for the 7828A. If I happen to get a suspect low reading I can then reach for a 2nd opinion tester.
  8. F

    Poulan Pro P3314 scored piston: help me understand why this causes problems

    Summary: (from Poulan experience) After working on that type saw you will then be able to recognize a better built saw when you see one. You are getting chainsaw experience and that is best type to get chainsaw experience. Poulan (for occasional USE only) This is on the FRONT page of the...
  9. F

    Broken bolt condundrum

    You have lots of extra steel to work with if you take advantage of such before you screw it up further. I would think about just carefully drilling and taping to another size machine bolt. A size larger or if you have not screwed it up too much yet even smaller like 1/4-20. No need in trying to...
  10. F

    Craftsman part # 325692 Flange Bearing for Steering Assembly

    You will find that most generally saving a saved search is best to use two or 3 descriptions and maybe a used part will surface and at least one with the Briggs part number only in case a New Old Stock (NOS) surfaces. If you do a saved search for example a FLANGE BEARING you will get all kinds...
  11. F

    Craftsman part # 325692 Flange Bearing for Steering Assembly

    Also a saved search on flea bay will sometimes find a hard to find part. (and if you want to try for a spare)
  12. F

    Craftsman part # 325692 Flange Bearing for Steering Assembly

    Online search indicates partssupplies might not be very legit, possibly a phishing website.
  13. F

    Compression Tester

    AND a mityvac pressure/vacuum tester is a good thing if you plan on working on chainsaws. Do not confuse this mityvac leak test with a leak down tester that is used with a air supply that is used for checking 4 cycle gas engines for bad valves, rings, or head gaskets.
  14. F

    Compression Tester

    If you are asking about removing the welch plug to clean the carb and install a rebuild kit the answer is usually No to removing the welch plug and most generally rebuild kit cost about same as a replacement carb withtuneup kit not counting your time involved. Have to be careful or you can get...
  15. F

    Charging Problem

    You might consider using some fuse type breakers instead of constantly replacing fuses. They are reasonable priced. I keep some around for such use. Also get some fuse holders for the breakers and You can fuse down in the branch circuits. For example use a 20-25 amp as the main fuse but go with...
  16. F

    Compression Tester

    Here is some info about small engine compression testers and some more info at the arborist site with a search. You have to be careful when compression testing small cc engines and make sure your tester is truthful. I've had guys bring me chainsaws and other small cc engines that they had...
  17. F

    O-ring sizes

    Let him spend his time finding the parts. Quite often this is what it required to get a owner of old equipment the experience of what is required of a mechanic to try to repair their cherished equipment. (especially when they buy the wrong parts, but better them than you)
  18. F

    Cub Cadet LTX 1040 / Odd Forward and reverse Issue

    Have you tried going up a incline with the deck off after the drive belts gets warm???. This is too see if it will pull ok instead of just seem ok across flat ground with cold belts. I've seen cold belts pull ok for awhile AND both belts HAVE TO be replaced as a set. Simply installing the deck...
  19. F

    O-ring sizes

    Check out Crown Products, Inc. 3 locations in USA. They have been around since dirt. I get into old NLA stuff quite often, for example pumps, Hydraulic jacks. Quite often I see stuff like you see, not really worth the effort and pain and I send it to my donor salvage.
  20. F

    engine runs full out after 'rebuild' 287707 14.5 OHV

    Just couple hints: Do a static governor adjust. Make sure the throttle CABLE is located proper under the cable clamp so as to get a choke and return to low rpms when the throttle on the dash is moved to idle. Sometimes and this takes a bit of trial and error: Because the governor shaft only...
  21. F

    Hard to start

    Just another hint to not overlook. May not be your issue but just saying, it's not always the mechanical release that causes issues. I've seen some of the Briggs single cylinder Intek cam's that the cam lobe wears down. Not enough lift.. Seen one that was almost completely round.
  22. F

    Hard to start

    Just some more general info about your engine: Another GOOD reason you need to REALIZE is IF the compression release on the camshaft is broken, chunks of metal pieces is being churned in the engine oil sump and WILL EVENTUALLY make their way into gears internally and completely ruin the engine...
  23. F

    Hard to start

    Yes, leave the feeler in place if you want to save lots time at first. You can crank the engine with a 1/2 inch ratchet on the flywheel nut to SLOWLY turn the engine and watch for the intake bump holding the feeler gauge in manually held in place first with lash in specs then gradually reducing...
  24. F

    Caught fire now smoking

    I've had good luck with the clone carb's from HIPA on Amazon. Most generally Amazon has a FREE return full refund also with a certain number of days so look for such. If it won't work ok and you think it's the carb just return.. You will find that the WALBRO carbs are NLA. If you try to use a...
  25. F

    Hard to start

    What I do instead of WASTING time IMMEDIATELY adjusting intake valve lash when I FIRST encounter SUSPECTED valve lash issues, instead of immediately adjusting the intake lash with tools, I just check using feeler gauges and whatever it gauges, for example .006, I just insert a .003 gauge to...
  26. F

    Hard to start

    The compression release is on the intake valve. set the intake valve lash at .003 with the piston 1/4 inch past TDC on the COMPRESSION STROKE. If it still hangs insert a .002 feeler under the rocker so as to take the lash to .001 and test crank thru with the spark plug cable disconnected. I've...
  27. F

    Hard to start

    Explain Hard to Start is it hanging up on compression stroke, not cranking fast or what?
  28. F

    Caught fire now smoking

    The fuel solenoid does not stop fuel from leaking into the crankcase. It's a antiback fire solenoid. Just let the engine idle for awhile before killing. It's not really needed. Some guys just cut off the plunger instead of spending big buck to replace something that is not needed. Also it's best...
  29. F

    Briggs 422707 opposed twin carb

    That is the same plugs that I use because they are readily available. I really do not like CHAMPION plugs but they last a long time in the opposed twins. If you ever run into a opposed twin that will not start up when the engine is hot and you install new plugs and it's ok for awhile and does...
  30. F

    Briggs 422707 opposed twin carb

    The little throttle shaft dust sponge is in some of those type carb gasket kits. (easily overlooked when it falls on the floor) When the carb gets old they usually just rot away and no one ever knew they were ever in place.
  31. F

    Briggs 422707 opposed twin carb

    I just noticed that in Post #1 the air filter metal base has a screen. In post #8 no screen. I've never seen a screen at the base. Good idea to capture a base screw if one gets loose. I've found a base screws under intake valve and also imbedded in top of piston. Have to do a double gasket or...
  32. F

    Caught fire now smoking

    If you do not have a service manual search on-line for how to set the valve lash at .003-.005. (and sometimes on some older engines the valve lash will change again after the engine is operated awhile requiring a adjustment for a 2nd time. (so do not be surprised if you have to do such)...
  33. F

    Caught fire now smoking

    Strange one you need to be aware of on that carb. You also need to replace the upper old gasket on that Nikki carb. Trying to reuse the old gasket will result in gas seeping and BYPASSING the needle/seat. You can see such once the gasket is removed and you are aware of such. I pressure test the...
  34. F

    Briggs 422707 opposed twin carb

    little leak, big leak In the category of being just a little bit pregnant.
  35. F

    Caught fire now smoking

    What is even more exciting is do that with a flooded chainsaw between your legs when it ignites. (spark plug out) Looks like a fire breathing dragon at the crotch vital area on fire. It gets worse trying to whack out the britches flames without severely bruising your vitals. You will not ever...
  36. F

    Briggs 422707 opposed twin carb

    Some general info about the Briggs twins: (from experience) Keep a heads up on the 3 screws that hold the air filter base. If one vibrates loose it has a direct shot into the intake and into the engine. I've found some engines with a screw imbedded into the top of the piston or hung under the...
  37. F

    Briggs 422707 opposed twin carb

    I see in one of your posts that you wished the carb for them had adjustable jets. Some do. I have some that have one adjustment jet. Some can be very critical (1/8 turn) for good idle from cold to hot engine. I have several in operation that are the non-adjustable and they work good, but every...
  38. F

    Briggs and Stratton Intek v-twin 20hp

    I checked and the 1N4007 is what I use. They are trouble free unless molested. I think maybe a guy by the handle of Star tech on this site recommended those to me few years ago.
  39. F

    Briggs and Stratton Intek v-twin 20hp

    No. Not really on the Briggs twin Inteks engines. The diodes usually fail due to a external cause. (for example a leakage current in the ignition switch) But as you found they can be a real pain when one gets intermittent erratic I don't remember the 1NXXXX numbers on the diodes I use as...
  40. F

    Surging motor on NEW carb!?

    Did you get a HIPA carb? (just wondering) If it runs smoother but throttle rpms are way off check the STATIC GOVERNOR ADJUST.
  41. F

    Craftsman T-240 Deck Spindle Grease

    I've got a pile of grease guns also. When I was younger and in the hay fields with Dad my job was to grease the eq when they were taking a break, when I was not hauling hay. (and make sure the water can had ice) Had to refill the old style grease guns from a 5 gal bucket of grease, then usually...
  42. F

    Craftsman 917.370724 drive engagement cable

    Seen this from ebay that they are sold our right now. I would ADD this description as a saved search also. Be aware that you will get some notices that ARE NOT exactly the cable you are looking for, so review the pictures carefully even if the part number matches. OEM 196002 532196002 Craftsman...
  43. F

    Craftsman T-240 Deck Spindle Grease

    They cannot text with greasy thumbs or do a You tube google search. Phone becomes slippery. The grease and dirt will get on their phone screen. (and Lava soap is too harsh on hands and fingers that text) Several people (mower operators) do not know how to refill a grease gun or that they are...
  44. F

    Craftsman 917.370724 drive engagement cable

    As a final attempt you might try: If you can find a part number go to ebay and do a saved search. If none appears right now you will get a email when one matching your search DESCRIPTION appears. I would do at least two saved searches, one with just a description and using your mower model...
  45. F

    Simplicity, new battery won't start

    check out this link. https://www.lawnmowerforum.com/threads/the-big-disconnect-seperate-machine-and-engine-information-is-needed-we-are-not-mind-readers.81338/
  46. F

    Oil drain assembly question - trying to fix leak

    Just a hint about UV viewing light, etc. What I did at first to make sure I could see the UV ok with the intended light when I first started is mix little bit of dye into some motor oil, just small amount of oil and a drop of dye stir it good and then see if you can see it in daylight, then in...
  47. F

    Simplicity, new battery won't start

    Be careful. If it blows/spits out gas when the spark plug is removed a ignition spark can easily ignite the spewing gas. Engine model, type and code will be helpful to US.
  48. F

    Oil drain assembly question - trying to fix leak

    As star tech indicates the use of UV dye can make sure you are working on sealing in the correct place. You might get a surprise that the leak is not where you think. Hot oil leak can mislead very easily and I've seen oil not leak when cold. Automotive stores usually has or can get UV dye KIT...
  49. F

    Surging motor on NEW carb!?

    Hump up AND GET ER DUN You did good.
  50. F

    Grungy gas tank

    I've been doing that type tumbling for several years, all sizes of mostly gas tanks. (tanks that are NLA or very costly). I've got a tractor with a 3ft diameter rear tires so I can tumble really slow. If they have pin holes I use Red Kote. Really surprised at some of the old tanks how shiny they...
Back
Top