Search results

Results 101 to 150 of 500
  1. H

    No forward or reverse after belt from engine to deck broke

    did you check the T-Box?
  2. H

    FR691V AIR filter UPGRADE

    Nice Kit
  3. H

    A question for help with my Raptor SD

    It is a pleasure to help someone like you. Thanks for the kind word.
  4. H

    Nikki carb questions

    As long as the spring is still intact, I have seen some that the intake elbow got out of shape and would not let the choke open back up. try loosening the intake elbow and push up on it and tighten it to see if that helps. If not take it off and trim a little off the inside of the elbow usually...
  5. H

    Engine Rebuild

    Some hydro systems do whine I have a Dixie Chopper that does as well. you might try some Lucas hydro booster and stop leak at about 20 to 30 %
  6. H

    No forward or reverse after belt from engine to deck broke

    Ok deck belt is not back on as long as the motion drive belt is still on and turning the pulley on the bottom of the T-Box what I posted about the T-Box still applies. I guess I assumed you put the deck belt back on. Check the T-Box like I posted. I am trying to tell you what could stop the...
  7. H

    Frustrated with a Cub LT 1018 No Start problem

    Check the spark. Take an old plug open the gap up to about 1/4-inch install the plug wire to the plug. Ground the body of the plug to the engine and spin it over and see if it has spark to jump the gap. If not up plug the kill wire from the ign modules and try again. When she tried to start it...
  8. H

    A question for help with my Raptor SD

    Install the kit. The axle mounting brackets bolt to the frame and the brackets are in the kit. You can get them through you Hustler or Big Dog dealer only they will be red.
  9. H

    No forward or reverse after belt from engine to deck broke

    When you put the engine to deck belt back on there should be no reason for it not to drive unless there is a problem in the T-Box. Have you taken the top off the T-Box and checked the gear oil in the box. I have seen the splines strip in the T-Box and not pull the pumps. Take the top off the...
  10. H

    No forward or reverse after belt from engine to deck broke

    Is the idler on the inside of the v belt on the left side off the frame. The idler should be 1 inches from the frame. The dump is the 5/8 hex headed bolt head that might have a hole through it. Open 1 1/2 turns to push the mower. To adjust the tension on the belt you loosen the engine mounting...
  11. H

    Dixie Chopper drive questions

    52114 hydro Gear filters
  12. H

    Poulan Pro RS800 transmission problem

    You might luck out and find one with a bad engine that your engine will fit on.
  13. H

    No forward or reverse after belt from engine to deck broke

    This unit has separate pumps and wheel motors you have to manually take a wrench and open the bypass valves on the pumps to release the hydros for it to roll. Heck of a mower I own four of this style mowers love them. Three of mine are 1999 and 2000 year models, I also own a 2010 model. Got to...
  14. H

    engine runs full out after 'rebuild' 287707 14.5 OHV

    To be on the safe side yes.
  15. H

    Input needed on replacing engine on 2006 Ferris IS 600Z

    If you replace it with a different manufactures engine you have to replace the muffler as well. FX and FT are Kawasaki's commercial engines. FT series max hp is 24, FX max hp is 38.5. FX large engines are pretty big would have to make sure it will fit. Briggs Vanguard is an awesome as well.
  16. H

    Not all carburetors are the same.

    I have never seen the air vain setup on that size engine. Are you sure of the type number on the engine looks like it has a digit missing.
  17. H

    Kohler CV15

    Best single cylinder engine ever built. They just don't go down.
  18. H

    Oil Capacity ?

    Years ago Kohler stated that straight 30W would develop air bubbles that would not support the lifters causing them to rattle.
  19. H

    Crankshaft part numbers

    797018 replaces 493362
  20. H

    Transmission Issue?

    https://www.peerlessgear.com/wp-content/uploads/2024/02/Peerless-booklet-for-website-FINAL.pdf
  21. H

    Oil Capacity ?

    You cannot run straight 30W in the Kohler Command series engines if you do the lifters will rattle.
  22. H

    Oil Capacity ?

    you are right
  23. H

    Oil Capacity ?

    I use the Kawasaki 10W-40 Oil in my CV20 Kohler. No problems. It looks like some of the engine manufactures are going to a higher multi viscosity oil especially in the summer heat to lessen oil consumption. Do you know what the W stands for?
  24. H

    Pully replacement

    Some of live long lives and others very short lives. Some live long lives and others very short lives. Or some of us live long lives and others live very short lives. Take your pick.
  25. H

    Pully replacement

    I guess you get a kick out of putting other people down when you can. Go back and read your last post and find the flaw in it. Have a good day.
  26. H

    Pully replacement

    Trying to do it from memory sometimes my memory isn't as good as it use to be.
  27. H

    Pully replacement

    https://www.dixiechopper.com/owners-manuals/
  28. H

    Pully replacement

    Flat Idler pulley 3/8-inch mounting hole.
  29. H

    54" deck. Uneven Cut

    Got a used JD and am fixing it up to sell. Noticed the paint was coming off in some spots. Took a puddy knife and it peeled right off the whole operator section right down to the rust under neath. I think they made that section of the mower and set it outside and let it rust until they painted...
  30. H

    Which Oil Filter ?

    https://www.bing.com/videos/riverview/relatedvideo?q=Best+Oil+Filter+for+Kawasaki+Twin-Engine&&mid=20BA94978EFE829FA25820BA94978EFE829FA258&churl=https%3a%2f%2fwww.youtube.com%2fchannel%2fUCPixKydtianMPzfAmYD8jrQ&mmscn=mtsc&aps=72&FORM=VMSOVR
  31. H

    Mower Keeps Dying

    Never ceases to amaze me why the manufactures use rubber gaskets on the fuel caps instead of neoprene gaskets. Like I always say you can educate ignorance, but you can't fix stupid. Oh yes for water in the fuel system use Sea Foam.
  32. H

    Craftsman Briggs and Straton 6.75 refuses to prim

    792040 is the air cleaner base you need to cure the problem
  33. H

    Hill climbing question

    You might try Lucas Hydraulic Oil Booster and Stop Leak. It thickens up the oil in the hydro and Lucas recommends a 20% mix. I have use it at 30% with no problems.
  34. H

    Kohler SV-601 - Fresh soot around crankcase closure plate

    I have never seen a bucket Motor. Motors are electric that use electricity to operate. Engines on the other hand run on gasoline to operate. I have seen and worked on lots of bucket engines. Matter of fact the Kawasaki FX921 and FX1000 engines are bucket engines. I like the concept of bucket...
  35. H

    Encore Blows Fuse

    sounds good I'll try that. Thanks
  36. H

    Encore Blows Fuse

    Switch is the same have the circuit breaker fuse. Can not be the fuel shut off solenoid it only throws the circuit breaker when key is turned to start position. I pulled the wiring harness and can find nothing burnt. Should have pulled the safety control module and tried it them but hindsight is...
  37. H

    Big Dog 54" Wont Keep The Drive Belt On

    Where I worked, we were a Big Dog dealer, and I replaced a lot of the bracket kits. It usually broke most all the brackets. The new brackets are much heavier.
  38. H

    Encore Blows Fuse

    Working on an old old Z52 Encore zero turn mower and it blows the 20-amp fuse as soon as I turn the key to the start position. I can pull the exciter wire off the solenoid and it still blows the fuse. This thing has a safety control module just wondering if it could cause the problem. I have...
  39. H

    Dixie Chopper Magnum, 2550KO.

    So, what is the model number of the engine on the mower? Model and spec. number please
  40. H

    Dixie Chopper Magnum, 2550KO.

    I don't think that engine has a compression release. Manual says the engine with ACR is a pull start. What cold cranking AMP Battery do you have? If it is a 230 cranking amp battery it is too Small. I would get the biggest one I could find and try it.
  41. H

    Kohler SV-601 - Fresh soot around crankcase closure plate

    All those engines I ever worked on had a closure plate gasket.
  42. H

    dixie chopper zee 2 48” Blade Replacement

    You measure the blades from cutting tip to cutting tip not straight down the length of the blade.
  43. H

    Kohler CH18S Spec #62513 Simplicity Sovereign

    If you are talking about the heat sink? That has three wires connected to it that would be the voltage regulator.
  44. H

    Kohler SV-601 - Fresh soot around crankcase closure plate

    Why would you run the engine without the blower housing? For any extended time. That would be like running your car without coolant in the radiator. The blower housing directs the air from the cooling fins on the flywheel over the fins on the cylinder to cool the engine.
  45. H

    Need Mower Recommendation

    The place where I use to work sells Dixie Chopper mowers. A customer bought a new commercial mower. Took it home and was mowing his yard. He lived on a lake and the place where he lived was on a bluff over the lake. He lost control of the mower him mower and all took a dive right off the bluff...
  46. H

    Uneven cutting Z412

    Could be a bent spindle shaft.
  47. H

    Ariens with 20 hp B&S

    Model type and code so we know what you have. If it is a single cylinder, it is probably valves out of adjustment or broken compression release on the cam shaft.
  48. H

    Uneven cutting Z412

    Switch them around and see how they line up. If they are still off, you might be able to shim the spindle to compensate for the difference.
Back
Top