Search results

Ok deck belt is not back on as long as the motion drive belt is still on and turning the pulley on the bottom of the T-Box what I posted about the T-Box still applies. I guess I assumed you put the deck belt back on. Check the T-Box like I posted. I am trying to tell you what could stop the...

Check the spark. Take an old plug open the gap up to about 1/4-inch install the plug wire to the plug. Ground the body of the plug to the engine and spin it over and see if it has spark to jump the gap. If not up plug the kill wire from the ign modules and try again. When she tried to start it...

Install the kit. The axle mounting brackets bolt to the frame and the brackets are in the kit. You can get them through you Hustler or Big Dog dealer only they will be red.

When you put the engine to deck belt back on there should be no reason for it not to drive unless there is a problem in the T-Box. Have you taken the top off the T-Box and checked the gear oil in the box. I have seen the splines strip in the T-Box and not pull the pumps. Take the top off the...

Is the idler on the inside of the v belt on the left side off the frame. The idler should be 1 inches from the frame. The dump is the 5/8 hex headed bolt head that might have a hole through it. Open 1 1/2 turns to push the mower. To adjust the tension on the belt you loosen the engine mounting...

52114 hydro Gear filters

You might luck out and find one with a bad engine that your engine will fit on.

This unit has separate pumps and wheel motors you have to manually take a wrench and open the bypass valves on the pumps to release the hydros for it to roll. Heck of a mower I own four of this style mowers love them. Three of mine are 1999 and 2000 year models, I also own a 2010 model. Got to...

To be on the safe side yes.

If you replace it with a different manufactures engine you have to replace the muffler as well. FX and FT are Kawasaki's commercial engines. FT series max hp is 24, FX max hp is 38.5. FX large engines are pretty big would have to make sure it will fit. Briggs Vanguard is an awesome as well.

I have never seen the air vain setup on that size engine. Are you sure of the type number on the engine looks like it has a digit missing.

Best single cylinder engine ever built. They just don't go down.

Years ago Kohler stated that straight 30W would develop air bubbles that would not support the lifters causing them to rattle.

797018 replaces 493362

https://www.peerlessgear.com/wp-content/uploads/2024/02/Peerless-booklet-for-website-FINAL.pdf

You cannot run straight 30W in the Kohler Command series engines if you do the lifters will rattle.

you are right

I use the Kawasaki 10W-40 Oil in my CV20 Kohler. No problems. It looks like some of the engine manufactures are going to a higher multi viscosity oil especially in the summer heat to lessen oil consumption. Do you know what the W stands for?

Some of live long lives and others very short lives. Some live long lives and others very short lives. Or some of us live long lives and others live very short lives. Take your pick.

I guess you get a kick out of putting other people down when you can. Go back and read your last post and find the flaw in it. Have a good day.

Trying to do it from memory sometimes my memory isn't as good as it use to be.

https://www.dixiechopper.com/owners-manuals/

Flat Idler pulley 3/8-inch mounting hole.

Got a used JD and am fixing it up to sell. Noticed the paint was coming off in some spots. Took a puddy knife and it peeled right off the whole operator section right down to the rust under neath. I think they made that section of the mower and set it outside and let it rust until they painted...

https://www.bing.com/videos/riverview/relatedvideo?q=Best+Oil+Filter+for+Kawasaki+Twin-Engine&&mid=20BA94978EFE829FA25820BA94978EFE829FA258&churl=https%3a%2f%2fwww.youtube.com%2fchannel%2fUCPixKydtianMPzfAmYD8jrQ&mmscn=mtsc&aps=72&FORM=VMSOVR

Never ceases to amaze me why the manufactures use rubber gaskets on the fuel caps instead of neoprene gaskets. Like I always say you can educate ignorance, but you can't fix stupid. Oh yes for water in the fuel system use Sea Foam.

792040 is the air cleaner base you need to cure the problem

You might try Lucas Hydraulic Oil Booster and Stop Leak. It thickens up the oil in the hydro and Lucas recommends a 20% mix. I have use it at 30% with no problems.

I have never seen a bucket Motor. Motors are electric that use electricity to operate. Engines on the other hand run on gasoline to operate. I have seen and worked on lots of bucket engines. Matter of fact the Kawasaki FX921 and FX1000 engines are bucket engines. I like the concept of bucket...

sounds good I'll try that. Thanks

Switch is the same have the circuit breaker fuse. Can not be the fuel shut off solenoid it only throws the circuit breaker when key is turned to start position. I pulled the wiring harness and can find nothing burnt. Should have pulled the safety control module and tried it them but hindsight is...

Where I worked, we were a Big Dog dealer, and I replaced a lot of the bracket kits. It usually broke most all the brackets. The new brackets are much heavier.

Working on an old old Z52 Encore zero turn mower and it blows the 20-amp fuse as soon as I turn the key to the start position. I can pull the exciter wire off the solenoid and it still blows the fuse. This thing has a safety control module just wondering if it could cause the problem. I have...

So, what is the model number of the engine on the mower? Model and spec. number please

I don't think that engine has a compression release. Manual says the engine with ACR is a pull start. What cold cranking AMP Battery do you have? If it is a 230 cranking amp battery it is too Small. I would get the biggest one I could find and try it.

All those engines I ever worked on had a closure plate gasket.

You measure the blades from cutting tip to cutting tip not straight down the length of the blade.

If you are talking about the heat sink? That has three wires connected to it that would be the voltage regulator.

Why would you run the engine without the blower housing? For any extended time. That would be like running your car without coolant in the radiator. The blower housing directs the air from the cooling fins on the flywheel over the fins on the cylinder to cool the engine.

The place where I use to work sells Dixie Chopper mowers. A customer bought a new commercial mower. Took it home and was mowing his yard. He lived on a lake and the place where he lived was on a bluff over the lake. He lost control of the mower him mower and all took a dive right off the bluff...

One on eBay for $60.00 $9.98 shipping

Could be a bent spindle shaft.

Model type and code so we know what you have. If it is a single cylinder, it is probably valves out of adjustment or broken compression release on the cam shaft.

Switch them around and see how they line up. If they are still off, you might be able to shim the spindle to compensate for the difference.

I have one of those, wall mounted balancers, love it and an Oregon blade sharpener as well

First thing I would do is get rid the oil drain and get the drain hose kit 51044-0902 off Amazon

If it is an HP model or EFI it will have ZT3400 hydros. You can try Lucas hydraulic oil booster and stop leak. I believe they recommend a 20% mix, but you can go 30% with no problem.

Kinda tired of people telling me I am too high. They can buy one on FBM for $300 or $400. Yes, some junk some guy cobbled together and they get stuck with it. I go over mine and fix what is wrong with it. Of all the mowers I have sold over the years have only had one give a problem, that was an...

I know it depends on age and how it looks and the condition it is in. Looks like people only want to spend between $300.00 and $400.00 for a used mower. They also want it to be in pristine condition. Do any of you guys that sell used equipment have any $300.00 to $400.00 mowers