Search results

Yikes! I'd go nuts if it took me that long to do my 2-1/2 acres, which I can do in 45 minutes on my Ferris IS2600Z. But for those who enjoy a leisurely ride have at it .....

a couple of pictures of the property you're maintaining would be very helpful to help determine what may or may not be a practical machine for the job, i.e. is the lot level or grades & smooth or rough, trees, etc. Aside from that, I'd start by looking at the Z320R ZTrak, better seat w/armrests...

check out these - they should be the correct ones - Gator® G6™ Blade, 18" Part# 396-806

what millennial or younger generation even knows what a manual can opener is.... ahahahahaaaaa

ahhhh, the good ol' WWW; hmmm, while there are many good tutorials and video's showing how to do tasks correctly sadly there are too many that are BS and cause more problems than they solve. As Dirty Harry might say, "I man has to know his limitations....."

are you any good at retrofitting things....

what exactly is your position/job in this project...?

have you tried just tapping on the leading edge of the starter with a small mallet hammer ....

still whining "because of the dictator in Washington"; hmmm, last I heard that person is voted into their position by We the People, i.e. customers..... maybe you should put up a sign stating you only service the equipment of democrats. Try that and get back to us!

I have a Makita G4101R - 4K generator that I have stand-by ready - winter, spring, summer, or fall. Power outages know no season, and refrigerators need power sooner in the summer than winter. So, I fire up it up at least bi-monthly. Just turn the fuel on long enough to start and run about 5...

Hmmm, do "Parts Tree" and "Jacks Small engines" not ship to Australia ... ?

try a full set of Oregon G6 blades, I don't use anything but anymore..... long lasting and cheaper in the beginning

I'm going to go out on a limb here and say that what you heard was Kanye West singing his version of "Help, I need somebody...." - yes???

spark plug helicoil repair kit https://www.runnings.com/powerbuiltr-spark-plug-thread-repair-kit-14mm.html?gclsrc=aw.ds&gad_source=1&gad_campaignid=23169895817&gbraid=0AAAAADmj6pmXp3WuIQPhWepbv_y34wWLK&gclid=EAIaIQobChMIhZjvl6f0kAMVT07_AR1TOQSFEAQYBCABEgLxSvD_BwE

can you, or a knowledgeable friend rebuild this engine...? It shouldn't cost that much, or take too long, and well worth the effort.....

the deck on my 1981 Case 108 is still as solid as the day I bought it.... just scrap it clean once a month and blow dry everything as already mentioned.

I'll guess on this one - Cub Cadet.... and the winner is?

:unsure: ... 1985 EXCEL HUSTLER 251 Landscaping Lawn Mower..... I take PayPay ... ☺️

¿Qué carajo te pasa?

ohhh my, too funny..... some people need to have their sensitivity meters calibrated . . . . . . :ROFLMAO:

well, maybe you'll get lucky with Rachel.... :love:

Ya, you're probably right ..... Joe had some fine people, like Samual Brinton" who was only in charge of the Department of Energy and Admiral Rachel Levine. Outstanding choices!!!

ACDelco GM Original Equipment PF2210 Engine Oil Filter there are much better deals out there is you just cross reference the Kohler # and shop around... $25 for a simple filter is ludicrous..... 😱

hot climate SAE 20W-50 or SAE 10W-30 cooler climate

were you holding your breath when you wrote this.....? Punctuation can be your friend , . ; - ! 🫣

Have you tried "Oregon" replacement parts...? I switched to them, and never looked back.....

being a poster who felt a while ago that this site was suffering and needed to be put down and end its suffering, I have to now say that it has apparently seen the light and has been given renewed life. No issues observed here of late ..... yippee!

it just needs a solar recharge panel to charge on the go.....

next up, an 80-page thesis on oil viscosity and flow rate . . . . . :unsure:

what are you putting them on...? https://gripstuds.com/collections/tractor-studs?srsltid=AfmBOor_QuACMRP5C21SYv8XCzkDrHMUNCTUEeJCYVVDjXEdzLSd9snA

Now you've gone and done it..... some years ago, I was passing by a Monroe Muffler shop it dawned on me my oil was overdue on the 2-year-old Jeep I was driving, and since their lot was almost empty I "thought" I could get in and out quick. Well, I got in immediately; but, 45 minutes later my...

interestingly, my JD x585 has a drip tray that the engineers designed to catch the bit of oil that spills out when replacing the filter. It's also nice hold JD has a flexible drain tube, so you can direct the oil flow into a container, and not all over the machine or floor. If they can do it...

what you talk'n 'bout Willis, can't you see MY lawn is perfectly level..... 🫣

I only posted those to show that the blades cut minute clippings and didn't leave rows of mulch or strips of high grass. The grass was still very damp, and the wind was almost blowing me off the machine. The cut is consistently level and even, and this whole area is our leach field, so I don't...

I hear you.... since this problem seems to have started immediately upon getting this unit, and other customers have had/are having the same issue it seems this is an inherent manufacturing deficiency... time to trade the dang thing in for a decent machine!

Hmmmmm, well imagine that . . . . . Cons & Common Complaints Cut Quality: Some reviews indicate that the mower may leave "stragglers" or doesn't cut evenly in very tall or thick grass, potentially requiring a second pass

some before and after results with Oregon G6 mulching blades set at 3" with the grass currently at about10" and damp grass today . . . . the leaves and bark are from a couple Sycamore trees, huge leaves and tough bark - - -

small 22 caliber directly through; but do it in the grass, not a concrete floor ..... 😱

Uhmmm, I'd guess that softer tires will just cause you to scalp the dickens out of the lawn. Maybe try aerating on a rainy day and then rolling it to level things a bit . . . . . jmo

Oh come one, really....? This is exactly why Vise-grips were made... sheezzzz!

I'd blame the Gravely not the blades.... the blades worked great on my Gravely, it was the Gravely which was a POS, hence the JD's.....

maybe a set of these..... Marastar Turf Traction, they work great on my slopes

I've used Oregon G6's on a Gravely XL2148ZT, JD 345, JD 585, and now my Ferris IS2600 and never had a bad cutting or build up under the deck. That includes cutting 12"+ deep wet stuff . . . . .

go mow your yard/lawn and take a good photo showing the mohawking so we can see for ourselves

if the blades are not level that can cause air flow disruption and weird cutting issues - Google can be your friend too..... A "lawn mohawk" is typically caused by improper mowing, such as dull blades, uneven mower decks, mowing too fast, or excessive grass length. The blades are either torn...

if the pressures are way out of range from one another then the deck can't be level....

check that the towing disengagement lever(s) haven't popped out... I doubt this is the problem but worth checking first.

maybe this video will help - - -