Recent content by viperv10

  1. V

    Lawnboy Duraforce Commercial Surging

    Every durforce I ever had, I swapped out the pilot jet with a Briggs & Stratton pilot jet no. 801308. The diameter is slightly larger than the stock one. The pilot jet is on the side of the carb under a black sticker. It helps the engine run a little richer. I have varied success with the cheap...
  2. V

    Stealth HD mowers

    What do you guys think about the Stealth mowers. Last year I was looking for a new HD 52 but my dealer only had the stealth 52. I didn't like the looks of the all black mower. My dealer said he would sell me the stealth mower for the same price as the regular gravely color. The stealth was a...
  3. V

    Honda pulling back is like having the brake on

    That could be. I'm a lawn boy 2 stroke fan myself. But I like the hondas that have the rear discharge.They don't throw the clippings out into the street or against the house or flower beds.
  4. V

    Honda pulling back is like having the brake on

    I have 2 honda gcv 160 honda self propelled walk behinds. Both of them are hard to pull back on. Are they all like that or would it help if I adjusted the cables one way or the other. I have a newer gcv 170 self propelled that pulls backwards just as easy as forward. The first gcv 160 I replaced...
  5. V

    Hose Routing

    Thank you for your replies. I found a diagram of the fuel tank and I see that there is a nipple on the top for the vent hose. I appreciate your help. Jerry
  6. V

    6.5 Duraforce lower seal missing?

    I found a piece of pvc pipe about the same diameter of the crank seal and cut off a piece about 8 inches of so, just as long as it is longer than the crank. I lube the crank seal a little ID and OD and tap it in place with the pvc pipe and hammer. Tapping lightly until it seats. Regards
  7. V

    Hose Routing

    My brother in law pulled off a hose on his mower thinking it was the fuel line but it wasn't. One end goes into a nipple on the plastic intake. The other end is a mystery. I think it is a pollution or vaccumm hose. We can't find where is it goes. We can't find a nipple on the fuel tank or the...
  8. V

    6.5 Duraforce lower seal missing?

    I have replaced several duraforce crank seals but none have ever had an extra retaining ring. But the parts diagram does show one. Seal is # 94-5767 and retaining ring is 98-7046. From my experience the mower should not be running very good if the seal was completely gone. It would be sucking in...
  9. V

    6.5 Duraforce lower seal missing?

    It is a lawn boy 2 stroke, there is no oil to check
  10. V

    1980 Lawn Boy

    It looks like one that I have. It will have a F100 engine with a plastic carburetor. The carbs are fairly easy to clean if you have any experience with small engine carbs. Clean it and get rid of the old gas in the tank and it should run fine. Regards, Jerry
  11. V

    Honda won't start without starting fluid

    OK thank you four reply. I noticed on this model the choke is spring loaded. when you set the choke, as soon as you grab the safety handle to pull start, the choke starts to open. you barely have time to pull the rope and the choke is opening already. I have never seen a set up like like this...
  12. V

    Honda won't start without starting fluid

    Hi guys, I was just given a troybilt push mower with a honda engine on it. They couldn't get it to run. I cleaned the carb but it will only start with starting fluid. So I took the carb off and cleaned it again. Still won't start. One shot of starting fluid and one pull and it starts fine. The...
  13. V

    8237 muffler / mufler cover question.

    It's been a long time since I had one of those mufflers off. I can't remember if that baffle is pressed in or welded in there. I have read where some people put the muffler on their grill for awhile to burn out the carbon build up. I would be weary of trying to separate the muffler. You may...
  14. V

    Identifying an old Lawn Boy mower

    Hello, I have had 3 different mowers with decks just like yours except not so dark green. I am guessing that yours is early eighties. A pre compliant mower, blade control handle I think they made the f-100's from 1978 to 1982. Then they started putting metal walbro carbs on a lot of F engines...
  15. V

    Duraforce carbs

    I have worked on several duraforce mowers and I have a problem with the air vanes sticking and the mower revving too fast. The air vane works free until I tighten the two bolts that hold the carb on and that seems to put the air vane shaft in a bind and it won't spring back. This has happened on...
Back
Top