Recent content by user4579

  1. U

    Reline mower clutch

    Did not know that! I did assume that on a clutch there was a lining. Thanks for your knowledge!
  2. U

    Reline mower clutch

    Good Day!! I was just wondering if anyone has found a place to buy the friction material to reline the mower clutch? we used to do this on the old dragline cranes and dump trucks. A new Warner (non China) one is about 300 bucks. So this is just a thought.
  3. U

    No oil pressure Kohler CH20 64632

    Yeah, I didn't think of that. I think it could be done pretty easily on the pickup tube, but I'd have to go most of the way to the top of the pump to do so. No doubt it would work. Thanks for the info!
  4. U

    No oil pressure Kohler CH20 64632

    Thanks for the reply! I have a new one ordered (Kohler) This one lasted 494 hrs. so I guess that's not to bad.
  5. U

    No oil pressure Kohler CH20 64632

    First, Thanks for the replies! Yes indeed mine is missing that "little" clip on the end. So, is this a once in a lifetime thing or something common? Maybe epoxy the new one in addition to that small clip? Next the rods and crankshaft look just fine so I must have shut it off in time. What I...
  6. U

    No oil pressure Kohler CH20 64632

    First, Thanks for the replies! Yes indeed mine is missing that "little" clip on the end. So, is this a once in a lifetime thing or something common? Maybe epoxy the new one in addition to that small clip? Next the rods and crankshaft look just fine so I must have shut it off in time. What I...
  7. U

    No oil pressure Kohler CH20 64632

    Strange problem, the oil seal on the crankshaft blew out and covered the belts on a Grasshopper 220 with oil so bad it quit moving. I thought no big problem just a seal. But now no oil pressure and it's full of oil. Removed the oil pressure sender for the light to make sure and nothing. So...
  8. U

    Grasshopper 225 Rear axle nut torque

    Thanks!! I couldn't find that info anywhere except on a generic torque sheet for nuts and bolts.
  9. U

    Grasshopper 225 Rear axle nut torque

    Good Day All! I bought an old Grasshopper 225 serial 5045813 year is a 2000, with rear axle seal popped out. So, I'm going to replace both sides and can't seem to find what to tighten the rear axle nut that holds the tapered hub with the disk brake on. It's a 1-inch fine thread nut but I really...
  10. U

    Sears Pressure Washer 2,400 PSI Model 580.768332 Serial 68110398 6HP OHV Intek

    Thanks for your help! I'll tear into it this weekend.
  11. U

    Sears Pressure Washer 2,400 PSI Model 580.768332 Serial 68110398 6HP OHV Intek

    Good Day All! Got this at an auction, said it runs great. And it does, but it sometimes won't go to the high pressure. When it does it will really go to town! So I figured just put an unloader Assembly in it and problem solved. But after doing that, the same, with it running and low pressure and...
  12. U

    Country Clipper Kohler engine identification.

    Thanks for all the help!! With it all tore down and nicely cleaned up I think I'll rebuild it. Won't take much, a gasket set and seals, quick hone, a cylinder head and a valve job on both heads. Thanks Again for the help!!
  13. U

    Country Clipper Kohler engine identification.

    Boy! Never would have guessed that! The throttle on this one opens all the way, and the coils are fixed in one spot but, they have 2 wires on each coil that go to a small electronic box on one of the shields. So, I'm pretty sure it's a 22 HP. But here is a funny thing, after getting it all tore...
  14. U

    Country Clipper Kohler engine identification.

    Well after a lot of cleaning I did find one number on the base of the block 24-560-11 but when I try to look it up I keep getting an 18 hp. Is it a universal block with just different bore sizes? At least it's coming as a Kohler number.
  15. U

    Country Clipper Kohler engine identification.

    Well after a lot of cleaning I did find one number i
Top