Recent content by jetpackjbd

  1. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Yeah, I bought a pack of new keys and had no luck. That was what finally made me give in and buy a new motor..
  2. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Final update: I managed to get the flywheel off using a combination of the flywheel puller, a hammer, and a crowbar. The flywheel key was sheared, but I think I originally sheared it in the process of getting it off... I replaced the key and still no luck, it backfires and smokes but that's...
  3. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Thanks for the reply, what should I use the rattle gun on? The bolts seem to be in enough, I thought I was supposed to be tightening down the nuts on the puller. I don't know if I can really use a drill on a nut in this case
  4. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Forgot about this thread, should post an update. The riding mower is still dead, despite everything appearing to work. It gives smoke periodically when starting, but doesn't turn over. I assume either the ignition timing is off or the valves are in need of adjustment. I gave a rough valve...
  5. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Got the blades sharpened and the 'transmission' adjusted. Works great! It needed a $10 cable but that was it. A total of $10 and a few hours of work for a like-new mower seems worth it. Will be working on the riding mower tomorrow, hope it runs!
  6. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Everything's back together, but still not starting. I suspect it has too much friction, since it's harder to turn than it should be, plus the starter is running slow. Going to try putting some oil directly in the cylinder tomorrow, as that's all I can do for now. In the mean time, I picked up a...
  7. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Thanks, didn't see this until after but I got it off with the impact drill. Now I just need to put everything back
  8. J

    Homelite string trimmmer runs on the first or second pull - but only for 1 or 2 seconds.

    I used to have this issue with my Homelite trimmer, would run for a few seconds but it wouldn't start till the next day after that. Believe I narrowed it down to a carburetor issue, so try some carb cleaner and maybe rebuild the carb. Good luck!
  9. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Currently struggling to remove one of the bolts on the new conrod. I've tried jumping on the torque wrench, hammering it, having two people try at once, spraying silicone lubricant, nothing. Impact drill is charging so I'll try that in a bit, but I'm a bit doubtful that'll work. If the engine...
  10. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    I cleaned that out with some thin wire and poured a bunch of the old oil on the piston. Sure enough, was able to pull it out! Thanks for the advice!
  11. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Ohhh, is a carbon ridge the carbon buildup on the edges of the top of the cylinder?
  12. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Thanks for the advice! To clarify though, I'm reusing the piston so I'd like to do as little damage as possible. Excessive heating might not work well. I'll try shoving a ton of oil in it though, hopefully it works. The piston moves but I just can't push it out. I'll try this in a bit
  13. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    I wouldn't doubt the previous owner tried running it on half diesel at one point lol. The conrod should arrive tomorrow, but I can't get the piston out. Any ideas?
  14. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Nah, I'm not really upset with B&H. It seems like the old owner didn't care for it very well, and it was 20 years old. We just needed something that could cut our lawn easily for a decent price. I've tore it apart and found the pieces of the conrod, just bought a new one. Hoping that fixes it...
  15. J

    Engine lets out a puff of smoke but doesn't even sputter when attempting to start

    Satisfied customer of you, unsatisfied customer of Briggs and Straton.
Top