Search results

Anyone using the mulching Kit? If so how do you like? Can it be left on all season? -bobby

Well, I turf tiger started right up today then after mowing for about 20 minutes i parked it. I got on it to start it up after about an hour and when I turned the key nothing happened. And yes, brake was, seat was down and I was sitting on it, control levers were out and deck was up. Any ideas...

Can someone post a picture of a scag turf tiger interlock switch that is works off the control arm? Thanks, -bobby

I have a scag turf tiger 61 inch cut. How do I remove the cover that has the electrical connections? The cover that the key goes into. The one that has the throttle and choke levers. There must be someone that has had to replace the pto switch at one time or another. In order to do so one...

I had my turf tiger serviced last fall. Today I pulled out the pto for the first time and the blades did not engage. I pushed it in and pulled again and they did engage but were slow to spin up to speed. After mowing a little bit I stopped and pushed the pto off and on and the blades started up...

I have a 61 inch turf tiger. How do I change the deck belt? What releases the belt tension? Thanks, -bobby

Well...I've got a ton or two of oak leaves that need to be mulched. How good are the eliminator blades when used with the block off plate? I don't have the hurricane mulch system. -bobby

Well...I sent my turf tiger in for service on Thursday and they brought it back on Friday. After backing it off the trailer the guy went to park it and upon pulling back the break it made a loud and i mean loud screeching noise. He immediately dropped the brake off. Upon putting the break on...

My friend bought a new tiger cat and discovered it doesn't have a gas gauge. Is is normal? -bobby

I finally was able to get grease into the zerk nearest the deck and see what i was doing at the same time. Lowering the deck helped. Previous post on here helped alot also, especially on how to move the pto shaft so I could see the zerk. Thanks to everyone who helped, bb

This is question if or Mackie but anyone is welcome to chime in. I am thinking about getting the mojack for my turf tiger (for cleaning underneath) . The only problem is that my garden shed is not large enough toleave it free standing and would have to be shelved after each use. How much...

This question is for Mackie but others are welcomed to reply of course. What do you think of using compressed air to clean the main air cleaner element by blowing air from inside out? I have a tool sold by Gempler's for doing just this. However, manual says not to use pressurized air to clean...

Having researched for months have decided that the mojack pro is probably the best and safest way to lift my turf tiger to clean underside of deck. I would appreciate hearing any comments yea or nay on the subject. One thing that is somewhat bothersome is the storage of the unit. I would like to...

It's unfortunate that manuals are written by engineers and people that build the machines and not by someone that has actually used and maintained them. For example, under lubrication section 7.1 it has lubrication interval for PTO spindle as "40 hours/Weekly". Which is it? Also what grease are...

What type of grease do you guys use on the spindles? -bobby

I have looked and looked and felt and felt and still cannot fine the zerk fittings on the rear wheels. Can someone point me in the right direction. Thanks, -bobby

Does anyone use a pull behind sprayer with their turf tiger? I want to also thank everyone that responded to my recent post(s). -bobby

I have a scag turf tiger 61 inch cut. I want to sharpen the blades. Do I unscrew the bolts from underneath the deck or from the top where the pulleys are? Manual doesnt really say much about changing blades. Thanks for your replies. -bobby

I'm confused. I have a scag turf tiger bought last year. To remove the blades do I get under the deck to remove the blade bolts or can that be done from above. Thanks ahead of time. -bobby

Where's a good jack point on the Turf Tiger?

Has anyone used a cordless impact wrench to remove turf tiger mower blades?

Has anyone used the Mulching Plate on the Turf Tiger?

Well...here we go again. It looked like at least for a few days that I had solved or fixed all the issues with my new scag turf tiger. Now this! A couple of days ago I noticed a few drops of oil underneath the left rear side of mower below hoses and wheel motor area. I checked the fluid level...

I have a new Turf Tiger and the digital hour meter stopped working at 15.3 hours. It is still lit but not counting the hours. What do you think is wrong with the meter? Thanks for all the replies. -bobby

Well...I finally found the zerk fitting near the rear deck on my turf tiger but only by feel (cant see it lying down). However, when they made the turf tiger they put a bolt right beneath it. You guessed it. Right where I need to place the end of my grease gun nozzle. Anyone with a turf tiger...

Anyone familiar with this overseeder? Regards, -bobby

The turf tiger manual shows a zerk fitting on the rear wheels. I can't find this fitting. Does anyone know where it is located. Perhaps the wheels have to be removed to grease it. -bobby

I have mowed 4 times so far this season. After each mowing I run the front of the turf tiger 61 inch cut up onto my trailer ramps. I get underneath the deck and with a putty knife I scrape. There has got to be a better way of cleaning the underside of the mower deck. Any ideas? Thanks for...

I have attached a pic showing my striper roller attachment on rear of turf tiger. As one can see it is not level with the orange sway bar that it is attached to. This makes the right side lower to the floor (ground) than it should be (my index finger will not go under right roller). I have...

I was greasing the rear zerk fittings and happen to notice my striping bar (roller bar) is not horizonal when in the up position. I don't see anything bent. Is there a way to level it? It was put on by the dealer. Also when I greased the rear U-joint a glob of grease came out. Hard to see what...

I need to grease my turf tiger and am trying find the grease fittings on the U-joints. Could someone please post a pic showing where they are located. Regards, -bobby

I have a Scag Turf Tiger 61 inch cut. What do you guys use to raise your mower for cleaning underneath deck? Will Jungle Jack be strong and safe enough? Thanks. -bobby

I just purchased a new turf tiger 61 inch cut. Is there anything I need to know about the initial breakin period?

I'm new to the forum. I just purchased a new Turf Tiger 61 inch cut. Is there anything I need to know about the initial breakin period?