Search results

Chainsaw will not start, has spark, compression is 150 PSI, Checked flywheel keyway is not damaged., coil adjusted. sprayed carb with starter fluid still it will not start. The saw is not flooded. any help would be appreciated.. Thanks in advance. Dogfish

This hedge trimmer will stall when turned side ways, replaced carb and fuel lines. Bringing it back parallel to the ground if i'm lucky it will continue to cut. Thanks in advance for any help. Dogfish .

NEED HELP I have a Briggs Engine Mode #l110432-0149-E1 OVH that will not start, it has a spark, I replaced the carb, still it won't start, it pops or back fires. I tried to check the valve clearance but there is a valve cap and then there is the rocker arm. The valve is not loose so I kind of...

Just got a 5 HP Briggs engine that is froze, it appears water got into the valves, now they are stuck the fly wheel will not even turn, I poured transmission fluid into the valves and will let it set for a few days before doing anythings else. would be thankful for any advice to help with the...

I have a Briggs Engine #126782-0129-01 code 95050558 and it has a carb #494217 the throttle connect to a control bracket # 692021 the carb choke plate has a choke return spring that I don't know where it is anchored. I have searched the net and found the exact same problem however, they didn't...

I have a Briggs Engine# 126782-0129-01 Carb# 494217 Control bracket#692021 and choke shaft# 494218. The problem I'm having is choke shaft on the carb has a spring that connect somewhere on the control bracket and I don't know where. I have searched the net and have not found a diagram. Included...

I have a Briggs model #126782-0129-01 and it has a carb #494217 I need the linkage setup. Thanks in advance. I have included a picture of the carb control. When moving the throttle it has no effect on the carb choke plate that is the area that I'm having problems in Again thanks for the...

I have a Troy-Bilt Sickle bar mower model 34034 with a 5 HP Briggs motor 126762. I am trying to find the carb linkage thank in advance. Bama49

UT 13144 Will be running fine and then all of a sudden it start smoking Not so much so from the muffler but from the top, it will smoke for a few minutes then it stop, what could be the cause. Thanks in advance Bama49.

I was trimming some brush and the trimmer stopped running. I changed the spark plug cleaned the fly wheel and the coil it still wont start, I tried starter fluid and that didn't help, the coil seem to be firing, however, the compression seems to be low. The valves and the piston cylinder seems...

I cranked A tiller and let it run for about 3 minutes and then moved the level from choke to open and each time it died. I set it to the mid way point and was able to make a row. However, it never worked with the choke wide open it would crank on the 1st pull and never shut off, therefore I...

I have a Tecumseh engine that needs to be rebuilt can it be stored without oil until I find time to rebuild it or should I add oil to the crank case. Thanks in advance Bama49 Roll Tide

I obtained this unit used it has a 5HP Briggs engine 130212 3250-01 with a pulsa jet carb and it would not crank, after rebuilding the carb it now cranks however, it seems to be running full throttle and very high RPM's the only adjustment is the fuel mixture and idle. At this point I don't...

I have a Briggs model no# 130212 3250-01 the motor would not start so I rebuilt it Now it will start however, it will not run it just sputters and then die. But if I move the linkage connected to the governor and Idle speed it will run good. this should be something that happens automatic what...

Having problems with a Toro mower at times the recoil is very hard to pull. I unplug the coil from the spark plug and turn the blade a few turns and plug the coil back to the spark plug pull the cord and it acts as nothing happened and cranks with ease. Engine LV195EA-362003b. Thanks in...

I have this Toro mower that would not start I determined that it needed a coil so I ordered one in the meantime I took off the fly wheel and head to see if the shear pin was broken. The piston and valves had a lots of carbon on them so I clean them up. However, I wanted to know with the magnet...

I have a Murray 40508X92F will not start unless the starter is shorted. I have changed the solenoid and key switch with the same result. So I assume that it the safety switches either the PTO, clutch or wiring is at fault, we have verified that the seat switch is good. Can someone tell me where...