Search results

I am having a problem with the PTO on my JD 445 law & garden tractor, the Mower has not been used since last year, Got it out and running, when I pulled up on the PTO switch, The Knob just pulled out of the switch, >< So I went to the JD place got a new switch >< when I pull up on the PTO...

I have a Toro 3000 with a Force Deck, its a 52 inch cut, this time of the Year we have Clover growing in the yard, I never cut grass until afternoon, because of the Due that we have in the Mornings down here, any way the clover has a lot of Juice in it and it guns up under the bottom the Deck...

I have a 16 HP B & S Vanguard V Twin Type 916928 Mo# 303777 Its on a JD LT 166 >< on the Top Right side of the Carburetor just about the same Level as where the Gas Line comes in, there is a small Nipple/Tit very small, maybe a little bigger than 1/8 in. this fitting has nothing on it, and I...

I have a B & S 16 HP V Twin, MO. # 303777 it is on my JD LT 166 Mower, it had been running fine, today it started up, then acted like it was running out of gas, I choked it and it restarted, but died just as soon as it started, I removed the in line fuel filter, had good flow of gas to the...

I am wonder what a Good J D LT 166 Mower Deck is worth, it a 46in. cut, has never slept out side, good belt, not new but not bent up, ready to hook up and mow, what would be a fair price for it,

I have a 6 HP Tecumsen OHV Motor, ( ENDURO ) Spec. 7117 E -- Engine Family 2TPXS. 195B I pulled the bowl off the carb to clean it out, I didn't notice which way I took it off, which way does the flat off set in the bottom of the Bowl go, or does it make any difference? I figure it does, This...

Well we went ahead a got our ZTR, we had looked at Gravely, Ex Mark & Toro, the Gravely had to be taken off our list because the nearest Dealer was 35 Miles away, the Ex Mark & Toro were at the same Local Dealer about 15 miles away, we picked the Toro 3000 Series because of some features it has...

Today our New Toro 3000 Series ZTR was delivered, it looks to be a Beast, have it full of gas & will try it out later today, sure looks to be easy to service, Oil filter is easy to reach, & oil drain line is also very easy to reach, that has been some of the things I have noticed on some mowers...

Well today My Bride & I Bought what we Figure will Be the Last Mower we will ever Need, I am 75 & she is close behind me, we Pulled the Trigger on a Toro 3000 Series ZTR Mower with 52 In, Deck, The dealer had to get it sent in from some Place, so it will be a few Days before we can get our hands...

I have a 1990 Troy-Bilt Econo-Horse Tiller, My Problem seems to be that some way it is locked up in gear, maybe between forward & reverse, if i start it and try to make it go farward it bogs the motor down, same if try to go to reverse, would any of You have any experance with this Unit, Thanks...

Wondering if any of you have any Pro or Cons about this mower, I see a 2010 JD Z445 ZTR with a Kawasiki engine that has a 54 IN. Deck with 138 hr. listed for $ 4225, my question is what type Hdy Pump & Motors did this year have and what was the Oringal selling Price, is this a Heavy Duty Mower...

I had a Dealer that sells Both Ex Mark & Toro, tell me that Ex Mark owns Toro, that a Toro ZTR is about the same as a Ex Mark, Do any of you know anything about if this is True? Thanks for Your Input Rat

This Mower runs great when I start it up, go cut grass doing fine, after about 30 to 45 min it starts to lose some power & keeps getting worse making me slow down, if i stop & shut of the engine it will crank right back up, if i wait 15 sec and crank it back up it will run just fine for...

Though I would share this with you'll, Today i was mowing the yard, after about 30 min. of stedy going, the engine started to cut out and boging down, i had did this the last time i mowed, so i had changed the fuel filter, had me stumped, it was just about to quit running with no load, i...

I mow about 4 ac with a JD 445 LT with 60 in cut & a JD LT 166 with a 46 in. cut, Most of the mowing is done by the 445, the JD 166 is needed in a couple place that the larger deck can't get to, Both mowers are over 10 years old. Plan to finish out this season with what i Have, Unless I would...

I am needing to change the gas filter on my J D 445, I have located it, its inside the frame on the right hand side, is there any trick to it, Looks like i will have to remove the deck, any short cuts Please help Thanks

This Old Man Needs Help !! Can One of You tell me if the Hole in the out put end of the Crankshaft is Right or Left Hand Threads. Tecumsen Enduro 6 HP Model OHH60 - Spec. 71177E - Engine Family X2TPXS. 1951AB This Engine is on a Cyclone Rake, I have to Replace the Fan in the Blower Unit...

Need some Advice, I haes a 6 HP Tecumseh on a Troy-Bilt Econo-Horse Tiller it a 1990 model, All still Org. the recoil Pull Rope has gotten lazy about going back in, when i pull the rope most of the time it only goes back in about 1/2 way, if i keep messing with it, the rope will finaly go on in...

I think i have problem with the Solenoid Fuel Shut off on the Bottom of the carb, it want start, Book says that i should hear the Elect. Fuel Solenoid click when i turn on the switch, i dont hear anything nor do i feel it click when the key is turned on, i disconected the wire going to the...

Good Morning Guys, I have a Problem for You'll to help me solve this Morning, My DJ LT 166 will roll farward, but not backwards when i pull the free-wheeling lever, when i roll it farward it rolls easy, but there is a clicking noise as i roll it farward, I would sure like to hear what you'll...

Hi >< LakeRat1 >< I sure Could Use some Help!! I have a JD LT 166 Mower with a Briggs 16 HP V Twin Engine Mo # 303777, i need to get the starter off to replace the Bendix & it looks like i need to pull the flywheel, i have a puller but i dont know what size those bolt holes in the flywheel are...