Results 1 to 5 of 5
  1. #1

    Join Date
    Aug 2019
    Posts
    7
    Location
    Canada
    Mower
    Honda

    Honda HRm215 replacement tires

    HI guys, does anybody have a part number for replacement rubber tires that would fit my HRM215, dont want to replace the whole wheel.

    Thanks

  2. #2
    bwdbrn1's Avatar
    Join Date
    Nov 2011
    Posts
    383
    Location
    MI
    Mower
    Honda HR215

    Re: Honda HRm215 replacement tires

    I looked at boats.net and it doesn't look like you can replace just the rubber part. Depending on which one of the variants of the HRM215 you have, the whole wheel doesn't seem to be that expensive. Under 7 bucks U.S. for the front ones.

  3. #3

    Join Date
    Nov 2014
    Posts
    12,739
    Location
    Australia
    Mower
    Victa slashers & Push , Rover Rancher II's, Cox ( several ) & White LT120 + GT 200

    Re: Honda HRm215 replacement tires

    Tyres were available for some of the wheels.
    However down here they were about $ 2 cheaper than the whole wheel complete with tyre.
    What a lot of people fail to understand is the logistical costs of parts can very easily become more than the actual cost.
    A tyre take up the same space in a warehouse as a whole wheel.

  4. #4

    Join Date
    Aug 2019
    Posts
    7
    Location
    Canada
    Mower
    Honda

    Re: Honda HRm215 replacement tires

    thanks, I discovered that the wheels from a HRR216K9 will work just fine, and a lot cheaper, all I did was remove the drive sprocket off the rear drive wheels on my HRM215 and installed them on the front wheels of the HRR216K9 and the only other thing, the wheels are grey instead of white any questions, just ask

  5. #5

    Join Date
    Nov 2014
    Posts
    12,739
    Location
    Australia
    Mower
    Victa slashers & Push , Rover Rancher II's, Cox ( several ) & White LT120 + GT 200

    Re: Honda HRm215 replacement tires

    We havw different models down here as we get either the EU or AP models.
    Most Honda wheels can be interchanged.
    If your mower has the speed washer to hole on the front wheel then you just take about 1/8 " off the inner flange & the wheel slips strait on.
    For another I use the cheaper wheel then replace the plastic bushing with a toro front wheel bearing that has no flange on the inside & a flanged Honda bearing on the outside.

    Because the commercial range all weigh way too much, the bulk of my commercial clients are either using the old 3 speed with no blade clutch or dead man's throttle or current domestics, flywheel brake removed & stop switch replaced.
    We have swing back blades down here so they all fit 4 x high lifts because it packs about 3 times the grass into the bags.
    The cost of this is scrubbing the rear drive tyres bald in a single season ( about 1200 to 1600 hrs )

Similar Threads

  1. Honda Hrm215-cm
    By EasternCutter in forum Small Engine & Mower Repair
    Replies: 0
    Last Post: 06-18-2018, 12:02 PM
  2. Repairs Honda HRM215 - I broke the self-propel feature. Honda gurus required!
    By AltheaToldMe in forum Honda Forum
    Replies: 3
    Last Post: 05-04-2018, 10:36 AM
  3. Replies: 4
    Last Post: 03-21-2015, 02:02 PM
  4. honda hrm215
    By roadking in forum Honda Forum
    Replies: 4
    Last Post: 08-02-2012, 01:13 PM
  5. Honda HRM215
    By tom dorum in forum Small Engine & Mower Repair
    Replies: 1
    Last Post: 09-02-2011, 09:51 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •