Search results

Greetings, Has anyone else had PTO bearing failures with newer Echo 2620 trimmers? We have an SRM 2620, SRM2620T, and 2 PAS 2620 that we run here with some older grey echo trimmers. The newer 2620 models seem to have PTO bearing failures very quickly. Our trimmers get used commercially and are...

Anyone have any info on what an Echo 755T backpack blower should be set at for Idle and WOT? Thanks

Greetings, Looking to purchase a dedicated pole saw from Echo. I have narrowed it down to the 2620 curved handle and the 2620 straight handle. The only difference I can see is the throttle handle is curved on the 2620 and the 2620H is a straight weed trimmer handle. Are there any other...

Greetings, I have a 1982 John Deere 210 that has a K241 engine. This machine has sat for a few years now and the mice got into it something bad. Before sitting I would use this mower occasionally for mowing and fall cleanups. When it ran it was a bit smokey but not terrible. Now after cleaning...

Greetings, I was hoping that someone here could help me out. I have a Toro Greensmaster mower that uses a 18HP V-Twin vanguard engine that I believe may have a solenoid problem. I have tested these before in the past but I can not remember how to do so. I have looked in the service manual and...

Greetings, Last weekend I came upon a used Echo CS-4600 Echo chain saw at a swap meet. It looked to be in decent shape and had a tag on it "pops but doesn't run" ($45). Upon pulling it a few times I indeed got it to pop a few times but did not run. A few hours later of thinking about it and I...

Greetings, I have a B&S 18hp V-twin model 350447 type 1116-E1 code 00021111. This is stuffed into a Toro Sandpro 5020. There is very little room to remove the starter bolts. Along the way someone used the wrong bolts stripping the starter mounting threads on the engine. I am going to try to use...

Greetings, I was curious what the factory recommended idle speed and wide open throttle speed is of a Echo PB-250LN hand held leaf blower. Also what is the recommended way to adjust if they are not within spec. Thanks for your input Sean

Greetings, I found an old Echo PAS 2400 (507422) on the back shelf of my workplace that had been sitting for some time. The fuel lines had a pin hole in them so I replaced them all with 90097Y fuel system kit after talking to my dealer. Added some fresh mixed gas and a clean up and she fired...

Greetings, A while back I was at my neighborhood dump and found a old Echo GT-225 trimmer (all grey) in the dumpster. It didn't look too bad and had compression so I brought it home. I found that the gas line was leaking and replaced it with a repower kit along with a primer bulb. it also...

Just browsing through Home depot yesterday and I noticed how different the battery operated tools have become. There are chain saws, blowers, trimmers, hedge trimmers etc. So my question is how tough are these new battery operated tools? 1. Does anyone use them in a commercial setting as in...

Greetings, I have a Echo 250LN hand held blower (May 2014 manufacture date) that I was told it "ran for a little while then just shut off and has no spark" After sitting on the bench in my shop over the weekend I tested the spark on Monday morning and it was good. Then I fired it right up, It...

Greetings, I have a Billy Goat push blower QB1004 with a 10HP B&S engine model 205432 that I replaced the pushrod part number 592673 back in February of this year. The original pushrod that I replaced had come off of the guide and became bent and I thought it seemed odd that this happened...

Greetings, I have a B&S v-twin vanguard model# 356447 code #06062211 type #0200-E1. The engine has about 3000 hrs on it. Today it has seemed to develop a drip of gas from a vent on the outside of the carb. What may be the cause of this? Stuck float? Fuel shut off valve not operating properly...

I just replaced one of my engines with a New 18HP B&S Vanguard v twin Model Number 356447 3079 G1 (serial Number 1804021104540). This goes on a Toro Greensmaster and the engine is connected to a hydraulic pump. I want to make sure the engine is running at proper high and low RPM. Does anyone...

Hello all I hope someone can help me out here. I have a B&S 18 HP v-twin model number 350447 type 1331-E1 code 04051311. I bought this on a piece of equipment last May with 2674 Hrs. This machine had sit idle for 5 years. The carb was shot and needed replacement when I purchased it. I cleaned...