Search results

I have a Hustler FasTrak that has slowed down when levers are all the way forward. It was a lot faster. It moves forward correctly and it goes straight but the speed of the mower is not as fast as it used to be, so the tracking is ok. Can I adjust the speed of the mower? The model # is 928382...

I have a White Yard Boss 950 chipper-vacuum that needs a new bag. All places I have checked show the bag discontinued. The part # is 964-0473. Anyone have any ideas of how I can get one? Thank you, Jerry

My mower will start with choke pulled out then dies. I cleaned the carburetor, no luck. Replaced the carb, no luck. Fuel pump is pumping gas to carb. Any ideas what else to look for? Could it be one of the coils going bad? I'm getting fire at both plugs but could it be I'm loosing one...

I am pulling my hair out trying to figure this out. I have a Husqvarna YTH21K46 with a Kohler SV610-0212 engine. It seems the safety switches aren't working in sync with each other. When I hold the clutch safety switch in, the mower will start and engage the blades. When I let go of the...

I have a 2007 Kawasaki Mule that the carburetor had been removed and re-installed but not put back on correctly. Does anyone have one that they could send me a photo or diagram of the carb so I can put it back on correctly?

I have a Dixon ZTR 1950 that will not go to the left. When I push the handle forward all I get is a squealing sound. Left handle works fine. I've changed the hydraulic filter and oil and it is still doing it. Is there an adjustment I need to make or is the pump bad? Any help would be...

I have a John Deere X304 that has a no spark situation. I had no spark on both plugs but when I disconnected the kill wire at the first ignition coil I got spark on that one plug but not the other. If I plug the kill wire in the first coil and unplug the kill wire on the second coil I get spark...

Will model # 331877-2371-G5 interchange with 331877-1371-B1 ? I have a bad motor and found someone selling the 331877-2371-G5.

My Hustler starts good when cold and runs good for about 10 minutes and then get real sluggish, smokes white smoke, then dies. Then it won't start again until the engine cools off. I've changed the spark plugs, oil and adjusted the valves. The fuel filter looks clean. Seems to be a fuel...

I have adjusted the valves to .004 Intake and .006 exhaust. When I turn the engine over the engine has a knock and the flywheel stops. Take out the spark plug and it turns over. I have cleaned the carburetor also. Prior to all this I had to replace the flywheel and alternator because magnets...

Anyone know what the valve adjustment settings should be? Does .005 intake and .008 exhaust sound right?

My Hustler boggs down when the air filter is installed. Runs great without air filter. The engine is a Honda GXV760. I cleaned the curburetor and installed a fuel pump. I put in a new air filter, same problem. Any ideas of what to look for?

My Hustler blades won't engage. I've replaced the PTO switch and get a click at the clutch but it won't engage the blades. I installed a new belt and everything on the deck look good. Is it possible the clutch is bad? I'd appreciate any ideas of what to look at next. Thanks, Jerry

I have a mower that will only start by slightly engaging the PTO handle. It also dies when you move it to reverse. Also the blades won't turn when you engage the PTO. Anyone have where I should start looking?

MTD with Briggs engine (Can't read the model # information, old mower) idles great but when I engage the mower it chokes and dies. I need help diagnosing the problem. I've removed and cleaned the carburetor, replaced oil, spark plugs, fuel filter. Any ideas?

My Z425 won't run. I cleaned and put a new kit in the carburetor, new spark plugs, changed the oil & filter, new fuel filter, new fuel pump, new air filter, new starter ( which is why started this project) and all it will do is sometimes start but won't keep running. When it runs it runs...

I have a Husqvarna YTH2348 with a Briggs & Stratton engine 445577 2187 G5 that I've been working on and its driving me crazy. I have cleaned the carburetor twice, put in all new gaskets, changed the fuel filter, adjusted the valves,new battery, oil and filter change, new air filter, drained the...

My craftsman YS4500 model 917.287241 won't start. It turns over but won't start. I've replaced the carburetor, spark plug, fuel filter, and checked the safety switch under the seat. Any ideas of what I check next?