Search results

Its a 14 tooth, will it come with the bendix spring a Thank Yound that bearing and clip at end of the shaft.

While waiting around for new Starter to arrive I disassembled it. I cleaned the Commutator and checked all segments OK. Brushes looked good Magnets tight and in place. The bearing ends looked awful dry so I applied a small amount of lube. The gear bendix moved fairly free but had what seemed a...

Lets be a little bit reasonable, If you are stupid enough to be run over by the turning deck maybe its better that they don,t produce offspring. I was referring to safety switches that stop the engine from starting/running. I fully realize that safety is sometimes trying to protect us from...

Why so many safety switches, are they really all that neccessary? Which ones actualy stop engine from starting ,electric and fuel from flowing? The seat switch has been unplugged for years now. Can I just disarm them? I just got a kit for the Walbro but I need to get the engine turning first...

Ok Now more problems It ran fine for 30 minutes drove around and Dethated yard. Parked next day hard to start but finally did. Drove to barn to get trailer and engine started to hunt rpm up/down. I went back to garage shut off looked over machine and tried to start. No start even with a shot...

Installed new aftermarket Carb. Won,t start unless spray fuel down the throat. Where does power to the solenoid come from and is there a fuse somewhere for this circuit. I believe the solenoid isn,t allowing fuel to flow inside the carb Help?

Thanks

Kohler 19 hp Model SV 590S Spec SV590-0220 SN. 4005615513 DOM 02/25/2010

My LTX 1040 has a Leaking Carb. At first it was just a drip from the solenoid area. This year when I fueled up it must have leaked thru the needle because when the air filter was removed fuel drained out. I need # for replace or rebuild to include all gaskets and orings and solenoid. The carb...

I need to rebuild or replace the carb on my LTX 1040 with the 19hp kohler engine. It has leaked from what appears to be the Solenoid. This year when I fueledup it must be leaking thru the needle. I removed the Air Filter and fuel ran out. So I need advice and parts # for a complete carb or a...

So tell me what bar/chain assy to buy Thanks

The Drive Sprocket has 7 teeth,does that mean what as far as chain/bar assy?

Hello Somebody out there knows something about this saw Help

I found it at a dump site. No bar/Chain and trigger lock is missing. So where is the S.N. located? I found no tags other than EPA and Saw shop decal. Would like to know what year of manufacture. I have no way for a photo/ What size bar/chain 45 CC Air Induction Thanks

So what should I check out. The belt has some wear but it works just fine in the higher settings . I guess I need to know why the deck doesn,t raise straight up rather than moving up and to the rear?

Why does the pto for the blades wind up faster when the deck is higher ? Belt and pto linkage are ok. The deck height system seems to me to be the culprit. Rather than lift system lifting the deck straight up keeping belt tension equal regardless of position. When raising it moves the deck to...

I started this thread for a No Start issue unless I sprayed down the plug hole. Then it would run only at high throttl settings. It would not start 5 minutes later I primed and primed no start. So is it possible I can clean with soap and water and possibly clean it out or is it ready for the...

Where are these rubber check valves????

Can spray carb cleaner be used to clean internaly a Zama W-26 Carb????

okay I just got in from garage. High was at 1 1/2 and the low was at 4 1/2. Is that a good reason for poor performance. It only ran when throttle was at wide open.; I will try to start today. Thank you

What would be the base settings be for a old Woodshark 14 inch saw? I live at 2500 feet.

Now that's a lot of good info. That popping you mentioned, It has done that on shutdown for the last couple years. Also, the tractor only has 150 hours total and I'm the second owner. So I think I will try to examine it a little closer and hopefully its only the solenoid that is the issue...

I would really like a reply that says something about the QUESTIONS that I asked. Thank You

Mower leaks fuel from carburator when shut down. I put a shutoff valve before the filter to temporarily solve problem 3 years ago. I,m guessing that its from that solenoid but its hard for me to see down there. Is that solenoid really necessary? Or should I buy a solenoid and orings? Does a...

I think I found the culprit. I removed barand chain again. The studs are pulling thru the case causing the bR TO NOT LINE UP CORRECTLY. The engine runs so good should I try to find a replacement case? Where do you suggest I buy one?

What is a 21 spline screw, is it a socket or ???

I can,t seem to find chainoil with the viscosisity labeledor anything about winter summer.It also won,t revup, what kind of screw heads are on those carb adjustments There is no plastic caps. Very small screw with no slot

Is there a adjustment for chainoil. My echo has a screw to adjust but I haven,t found anything on the Poulan. Is there really a weight for chainoil with temp changes?

UT03756

Oh well sounds like its ready for the scrap heap

Anyone have the answers to my questions?

B@S 8 hp Cast Iron Sleeve Model 194412 Type 1114-01 Code 92102110 Total Hours approx 50 hrs.The Gov. lever has 3 holes. The carb linkage is in the end hole. The big spring is in the hole closesest to the gov lever pivot point. The middle hole is empty.. I tore the carb apart and it was so clean...

Will somebody PLEASE reply to this issue!!!!!

Our altitude is 2400 feet??So does that mean the carb high and low screws need to be adjusted and if so cw/ccw and how much ? Thanks Jim Senn Athol Idaho

I need picture or something on th gov. spring adjustment. Transition from no load to medium load without the rpm lag. Is this common on a single cylinder? What iis the bolt looking adjuster on the gov levrer?What is the purose of the skinny long spring that surrounds the linkage?

Is adjusting the Governor spring necessary because of the gen age or is something worn? We live at 2400 feet, would that make a difference?. Ia carburator ice ever a problem for a gen of this type?

I have a Homelite EHRL 4400 approx 30 years old. I,m sure there can,t be 50 hrs run time. Last time used it had trouble transitioning between small load and larger load. Hesitation. I have just bought a B/S kit for carb. I would like to know how to adjust voltage and the govermnor. Is there...

EU-2000i

I disconnected both oil level and the on/off switch. I haven,t tried it yet because while looking around some more I found a very small diameter 3 inch long spring thats around the governor link disconnected on both ends. ??? I can,t remember removing it only the metal link itself. I can,t...

Its a 2010 gen. that I bough new. It ran well for a few years then the surging started. It would smooth out with half choke. Now it will only run when you put gas down the spark plug hole. But stops Is there a fuel pump on this unit. The knob that allows start/stop feels more that a electric...

Like I said Not even a pop when start attempted? Even sprayed fluid down the spark plug hole. How could I loose spark with just a carb removal. Please no more screwdriver talk. Will disconnecting the oil level switch plug wires allow it to start? Will ddiconnecting the start stop switch allow it...

Not surging but trouble isno start either. The carb was the cleanest I,ve ever torn apart. I still cleaned with cleaner and blew out all passages. Reassembled with original parts. Turned on fuel. No Leaks.. Checked oil level ok. gave it a couple pulls nothing not even a pop. Sprayed start...

How to no if its a OEM kit if I don,t know who made the carb. I can,t find a marking on it no where. I know its the original because I bought it new.

Model194412 Type 1114-01 Code 92102110 Homelite Gen EHRL4400HD

I need to find a carb kit or a replacement carb. The engine will not run constant. It just oscillates,/hunts/surges. I cant find any identying data on the carb. I have had the gen since new

How can I find out the base settings. I just received a genuine echo carb. The red caps are not completely installed so I can dial it in.

The bar was worn at the nose area probably from my abuse/use by me. The chain I sharpened many times and there was little left to sharpen. Parts wear o ut even oem and no abuse. Usually 2 tanks of fuel per oil refill. The only thing different this time is that I bought a Husq sprocket with brg...

Chain runs smoothly around the removed bar and freely around the drive sprocket with no bar. Its when assembled the bind/other issues happen. I still would like to know how much end float if any does the drive sprocket have.Should the thrust washer zero out the float? I,ve looked at every link...

It rotates fine, no binding with bar/chain removed. What about what i asked about in previous post, and why would I take a 159$ saw to a shop at a big shop hour rate? Like I said at the start I have replaced these parts several times in the last 20 years, but never had a issue.