Search results

I happy to say the little machine is now purring. First let me correct myself, there is only 5 relays including the starter relay. I replaced all but the starter relay which clearly was working. I went through the entire machine and cleaned all connections and used die-electric grease...

Gentlemen, recently aquired a John Deere LT133 M0L133A054289 from my father-in-law, who picked it up in a yard sale. Machine was missing it's hood and battery. Judging from the condition it had been in a flood at some point but someone had made an effort to wash/clean it, even had fresh oil...

Sir, your post made me go look again and ultimately cause me to discover the problem, thank you, ray

Gentlemen, you tips proved most helpful. I discovered two problems. The coil I replace earlier had a slightly larger profile and cause the vain to drag across it. I corrected this by simply sanding down the corner. Also, someone actually assemble the machine incorrect by attaching the...

model 20331 SN 290134829

model 20331 SN 290134829

Ladies & Gentlemen, I seek your wisdom. My mower will start fine but when cold it takes several minutes of sputtering and puffing black smoke to decide to speed up and run. It has new carb, coil and plug. Once it warms up and starts first pull every time and runs fine.

After a short blast of starter fluid with no response, I pulled the engine cover. Coil was clearly suffering from being wet somewhere in the past, very rusty and absolutely dead, once replaced it fired up quickly. Went ahead an replaced the fuel filter for good measure. Machine has no hood so...

Not sure I would use a .22 in my attic but I have a .22 pellet rifle that does the trick with no chance of pass through.. r ☺

Gentlemen, recently gifted this machine, it has sat in my father-in-laws garage for years, comes with no hood or battery and I never actually seen it run. Today I checked oil, appeared very clean, put gas and a battery in it and it started right up, only ran few minutes, cut of and refused to...

Soak overnight in Kroil Oil before you start. ☺

I have a model 20016, it has 6.5 Techumseh Givey, I have a MD 20016 offered 2002 to 2006, it has a LV195EA 6.5 Tecumseh, 20017 2002-2006 and 20018 2002 to 03 also had Tecumseh engines, the carb on my machine has primer bulb. Two press and it always lights on the first pull. I recently...

Sorry you see it that way, Ray

https://www.msn.com/en-us/money/companies/nearly-40-000-john-deere-mowers-recalled/ar-AA1wVkkK?ocid=msedgntp&pc=HCTS&cvid=9f740d29ae7a4792bc7363a4ef4bbb42&ei=40

https://www.harborfreight.com/9-piece-tube-pipe-nylon-brush-set-90631.html

Wash it / wax it / fix the crack and run it. You still got a better unit that you will find new without spending silly money. Cheers, Ray

After the last mow for the season, cleaned up the entire machine with special care under the deck. Give the engine a good cleaning under the fan, changed the oil and air filter, went to a WIX 51391 on the oil filter, largest so far. Put the machine up on stands to give the tires a break...

Windows 10 will reach its end of life (EOL) on October 14, 2025: it is true

Chain trap to full size cement block, you can move it around easily, but the largest coon will be out done by it, r

Kroil penetrating oil -...

Free app called Photoscape works well and is very easy to use. http://www.photoscape.org/ps/main/index.php

Wonder how many on here will vote to keep the same problem?

Yep, they just debunked Kamala's McDonald's job story, my my, both sides of the team are just plain liers, what the dems will do to put in stupid.......

Folks, for many years I have used the low price sprayers available at Harbor Freight around the home. The weak part in this sprayer is the O ring. Here's a link where you can purchase a replacement. Cheers, Ray https://www.oringsandmore.com/metric-buna-o-rings-26-x-5mm-minimum-5-pcs/

Hey, if it turns, oil it, if it slides, grease it. Don't spare the lub..........r

I would expect WOT until it went splash...

Please don't do this >

Kroll, best penetrating oil on the planet, lube it up and give it time to work, then figure out how to knock it out without buggering it up.. Good Luck Sir

Climate change or not, if we don't get the Boob out of the office we are not going to be able to feed ourselves..Ray

US Government, largest bunch of over-payed Jack' Asses one could possibly collect..

Someone explain to me why I need to have an emission inspection on a 2017 car? It is insane, the shop operator expected to be TIP'ed.. Got to Love it, Ray

Price point might go down if enough stop purchasing their products..

As bkeller500 indicated, it is much easier to trim with a wider deck, the one thing I wlsh my ZTR had is larger rear wheels for a better ride. This machine also has 20" rear wheels. Just something to consider, Cheers, r

JMHO< if you feel like you need ROPS and seat belts all the time, you need to be looking at a different design machine to do your cutting needs...

Does the harnes have a fuse installed?

Ya might want to give up on the sucker before the fumes hurt you. That's a lot of oil to be swallowing. May a trip to the local repair shop would be wise..

WoW, who wants a push mower that might get wet? Is there any amoung us that hasn't used the hose to clean off a push mower after it became clogged with grass.. Go Figure.. Got to share this one, while taken the stairs out of my pool, I asked my daugher to assist. The moment she engaged my...

Not in my world, r

Nope, but how many have you seen burning up.

Here's a better suggestion, why don't we call it the "BRANDON" .....

Well if they are all the same voltage you might connect them up in paralled and charge them, but not in series..r

Looking for a 21/22" FWD Push Mower, typically I mulch so I keep the discharge covered. Not interested in battery, would like power to go through thick though stuff and not have to slow down from a quick gate. Some of the stuff on the market is so thin the deck flexes when you raise the front...

Whow, so the truth comes out, thanks r

So why would you do this conversion, maybe because the oem filter is so far down it picks up way to much crap in the filter causing you clean it way to often, LOL

I'd rather drown the little buggers, r

Gentlemen, thanks, I have removed the engine cal couple time and used compressed air to blow it clean as recommended. I just wanted to make sure that was sufficient. I do like the idea of the long round brush and don't see that causing a problem. Last thing I would be inclinde to do is to...

Otherthan blowing is off with compressed air, what do you do the clean the top of a twin cylinder Kawasaki engine? thanks Ray

There a reason some don't have access to the internet

One has to wonder, around here the first thing that happens when getting a site ready to build is they remove all the top soil, then after the build they bring in sod and plop it on the hard red soil and wonder why it does not grow. Test all you want to, it is hopeless, Ya got to love it.....r