Search results

Results 1 to 20 of 88
  1. S

    Kohler courage v twin 23 hp compression release valve?

    The engine runs good. Only problem is that the engine gets stuck for like a second when you spin the starter over with key. Then it will turn over normally and start. What could be the problem?
  2. S

    Troy Bilt Bronco hard to spin over

    Thanks i will do that. But it does start after a few tries so would it still be valves?
  3. S

    Troy Bilt Bronco hard to spin over

    I have also replaced the starter, solenoid and battery.
  4. S

    Troy Bilt Bronco hard to spin over

    It has a single cylinder 19 horsepower briggs and stratton. 2018 year model. Will post model number later. So when you turn the key, it gets stuck like it has too much compression. Sometimes the starter will make it through and allow it to start. But most of the time the starter just gets...
  5. S

    Briggs and stratton 24 HP V Twin over revving

    apparently it was the muffler guard causing it to rattle like crazy and somehow make it sound really loud. I removed it and now it runs really good.
  6. S

    Briggs and stratton 24 HP V Twin over revving

    it over revs when i put the throttle all the way up, it idles fine on low throttle and medium throttle.
  7. S

    Briggs and stratton 24 HP V Twin over revving

    I will do that but it idles fine and when it’s half way throttle it runs pretty fast already
  8. S

    Briggs and stratton 24 HP V Twin over revving

    I have a v twin briggs 24 hp runs good but it sounds like it over revs when throttle cable is put all the way up. I’ve tried to adjust the cable but if i try to lower the maximum speed of the engine. The choke will no longer work properly. Any help is appreciated. Model: 44R677
  9. S

    2018 Troy Bilt Bronco starter is on even when key switch is on off.

    Yes that’s what i was thinking it would be i’ll make sure to replace it
  10. S

    2018 Troy Bilt Bronco starter is on even when key switch is on off.

    So i have a weird problem with this mower it’s a 2018 bronco with a briggs 19.5 HP. I tried to start it and everything was normal except that the starter kept on moving even after turning the key switch off. So i had to quickly disconnect the battery to make it stop. I’m thinking it’s the...
  11. S

    Replacing the muffler worth the effort ?

    it’s not very hard to replace the muffler as it is only 2 bolts for each cylinder i believe. You should also get hearing protection after replacing the muffler just in case.
  12. S

    Briggs 24 HP V twin doesn’t start after using.

    I have a simplicity courier z turn with a 24 hp v twin briggs and it has a problem we’re it won’t start after using for about 40 min to an hour. I am thinking that it is the carb fuel solenoid going out or maybe the ignition coils but i don’t think both of the coils would go out at same time...
  13. S

    Husqvarna YTH22V46 idles higher when it warms up

    Mower is in good condition. It starts right up, but the issue now is that the engine runs at about 2500 rpm’s in low throttle. It starts to get higher when it warms up but when it’s cold it idles normally. I assume it’s an easy problem but i could use help.
  14. S

    Troy Bilt Horse XP Riding Mower Moves Slowly after drive belt changed

    The belt routing is correct. I took a picture before replacing it. I didn’t touch anything else so i’m guessing it’s the belt? I will put on the old belt to see if it’s still slow. If not then it is something else.
  15. S

    Troy Bilt Horse XP Riding Mower Moves Slowly after drive belt changed

    The pulleys spin freely and the belt routing is good. I have already checked to see if it’s right but i’ll look again to make sure
  16. S

    Troy Bilt Horse XP Riding Mower Moves Slowly after drive belt changed

    It’s not OEM but it was the same size and all. Pulleys seem to be fine and spin freely.
  17. S

    Troy Bilt Horse XP Riding Mower Moves Slowly after drive belt changed

    i’ll post the model number tomorrow
  18. S

    Troy Bilt Horse XP Riding Mower Moves Slowly after drive belt changed

    I recently changed the belt on a troy bilt horse riding mower because the old one kept jumping off. Now that i put the new one on, it doesn’t jump off but now the mower is very slow and makes a squeaking noise like the belt is rubbing against something. I notice that the belt gets pretty hot...
  19. S

    Kohler Courage 22hp engine knocking.....

    had the same exact problem with the same exact engine. it didn’t knock when you turned it was running but when you started it it turned it off, it knocked but the bolts where slightly loose. so i tightened them and boom.
  20. S

    Troy Bilt Horse drive belt keeps coming off

    Model: 13WX79KT011 Video of belt jumping off https://streamable.com/aetmje The drive belt comes off when you press the brake. There is a large space between the light brown pulley and the bolt that is supposed to keep it from coming off. I could use a little help thanks
Top