Search results

Today I now have mowed my yard a total of six times. Five of the six times were light cuttings. I lowered the mower one more notch today to the last one to try it out over the whole yard. The rear wheels were not hard to adjust as others have complained since I always lift the wheels corner...

I have completed two total yard cuttings(1st one mostly weeds, 2nd one light grass) and 2-3 pine straw pickups so far. In between time I played around cranking the mower every few days to see how many pulls it would take to start. With the warmer weather it only takes 1-2 pulls. In cold...

Interesting, I had figured the GCV190 would have been easy to start just as my GCV160 is since they are both basically of the same prior design.

gotomow, did your HRX217 have the GCV190 or the GCV200 engine? My old Honda had the GCV160 engine that would crank 90% of the time on the first pull and in real cold weather you may have to add 1-2 pulls. After playing around a bit I think the trick in cold weather is to "prime" the engine...

You have been agreeing with my original assumption of fuel vaporization. I was looking for possible answers other than fuel vaporization, if any, that I have overlooked. The engine would probably start on first pull every time if I would squirt a little fuel into the carburetor throat first...

That is the physics class information you where learn about the characteristics of the transition of a material between the three physical states. Thermodynamics courses takes a deeper dive. My question is exactly what basic action is occurring during the longer wait times between engine pulls...

The weather here has been crazy as it was in the rest of the nation. It has been either too wet or too cold to cut the few winter weeds in my yard. During this time I did some testing with starting my new Honda HRX217YKA mower. I am retired so I have the time and with a engineering degree the...

Thanks!

Yesterday I used the Lowe's Chat window to check on my Honda HRX217VKA mower order as it never showed any status change since ordering 4days before. The computer chat said my mower had been delivered two days prior. I finally got a real person chat and they stated it would take 5-7 business...

My Honda HRR216 deck is developing more holes on top around where the last three inches of the blades spin. Every time I use the mower I believe another small hole appears so the steel deck is rotting away over a large area and a new deck is outrageously over $300. Replacement steel decks for...

I have been looking at swapping out the Smart Drive controls on my old mower to replace the Select Drive controls on a HRX217 which may be my next purchase. I finally noticed the obvious. Duh! Honda Select Drive pivots from the bottom and Honda Smart Drive pivots from the top. Too bad or it...

Thanks, I'll still be researching a little more while waiting to see if a HRX end of the year deal becomes available. My old mowers will end up going to a local men's drug rehab center that cuts grass for support. My Toro has given me more trouble with the wheels locking up when backing up than...

I have updated my pros and cons list and ranking due to additional information I have received. I am still leaning towards the Honda HRX217 instead of the Toro 21382 Super Recycler. I normally(Honda better) bag and rarely mulch(Toro better). Aluminum will eventually corrode if grass is left...

gotomow, Thanks bunches for your replies. You are slowly turning me back towards the Super Recycler with a Honda engine. So if I understand what you said correctly, the Toro Super Recycler should have bearings on all wheels and the rear drive shaft. whereas the Honda HRX217 has bearings on all...

Thanks for letting me know about the grease nipples on the wheels. That is a real plus! The Toro drawings appear to show only sleeves for the wheels so it looked like the wheels did not have ball bearings. For the Honda where are the plastic bushings? I have never seen any on the Honda I...

I may have discovered the solution for my issue with Honda Select Drive. I always interpreted the way Select Drive worked was to set the speed and when engaged that is what you got. No more, no less. From the Honda manual it appears there is some leeway in the set speed of a little above and...

I have been looking at the Toro Super Recycler 21382 with the Honda engine also but leaning towards the Honda HRX217 more so. Back story. I purchased a Toro Recycler with a B&S engine and it lasted about 7 years then I purchased another Toro Recycler which lasted 2 years until the Tecumseh...

I am very interested in purchasing a Honda HRX217 mower. The only issue I have is it has Honda's Select Drive. I already own a Honda HRR216 and am fond of the Honda Smart Drive system. I rather have the Smart Drive from the Honda HRN217 on the Honda HRX217 than the Select Drive the HRX217 now...

I rather have the Smart Drive from the Honda HRN217 on the Honda HRX217 than the Select Drive the HRX217 now comes with. After looking at the Select Drive mechanism a while I am wondering if you could cut off the downward wingtips tips of the V shaped Select Drive engagement lever (GRIP, CLUTCH...