View Profile: shiftsuper175607

10-16-2018, 08:26 AM

shiftsuper175607 replied to a thread Exmark Ranger Lawnmower in Exmark Forum

Different words mean differently to people...you need to be specific in your explanation. To me, cranking is the engine turning over. starting is...

2 replies | 73 view(s)

10-13-2018, 09:56 PM

shiftsuper175607 replied to a thread PP16H44B deck in Poulan Forum

from what I am seeing the Husqvarna and Poulan Pro share the same deck and the 532121423 replaces the 532144729 ...

4 replies | 87 view(s)

10-13-2018, 09:24 PM

shiftsuper175607 replied to a thread PP16H44B deck in Poulan Forum

Is that a 44 inch deck?

4 replies | 87 view(s)

10-12-2018, 09:56 PM

shiftsuper175607 replied to a thread B&D cordless blower to clean mower.... in Electric & Battery Powered Equipment

That's good to know. I thought about taking my Snapper battery into Lowes and trying it in a Greenworks… but, I do have 4 batteries, so I am good.

6 replies | 216 view(s)

10-12-2018, 11:24 AM

shiftsuper175607 replied to a thread B&D cordless blower to clean mower.... in Electric & Battery Powered Equipment

I was at Walmart and they had some 60V equip. on clearance. I bought the blower $74, String trimmer $99, hedge trimmer $109...each with charger...

6 replies | 216 view(s)

10-08-2018, 01:19 PM

shiftsuper175607 replied to a thread set my valves without a feeler gauge any sugestion in Briggs & Stratton Forum

Varying number of sheets of foil. Drink can strip.

5 replies | 159 view(s)

10-08-2018, 01:17 PM

shiftsuper175607 replied to a thread New yard machines 46" mower - cuts WAY too low in MTD Forum

How old is the mower? Did you take the deck off to replace blades? Are the blades upside down...check and see. We would need pictures to see if it...

10 replies | 204 view(s)

10-06-2018, 10:44 PM

shiftsuper175607 replied to a thread Transmission issues in MTD Forum

We had a detailed thread not long back about a similar sounding problem. It was wear in the deck and linkage etc...whereas only at highest speed...

7 replies | 210 view(s)

10-06-2018, 05:53 PM

shiftsuper175607 replied to a thread Hustler super z not charging the battery in Small Engine & Mower Repair

Is the battery good? What is the voltage when sitting on the battery? What is the voltage when the mower is running?

1 replies | 67 view(s)

10-05-2018, 01:40 PM

shiftsuper175607 replied to a thread Riding mower will not start. Replace battery cable? in Small Engine & Mower Repair

You do understand a battery can be bad and still show 12v ? Read the voltage when someone tries to start the mower. They can have a bad cell. have...

6 replies | 159 view(s)

10-04-2018, 03:05 PM

shiftsuper175607 replied to a thread Riding mower will not start. Replace battery cable? in Small Engine & Mower Repair

Take the battery and get it checked at an auto store Check at connections Try and jump start with a known good battery Most likely a bad...

6 replies | 159 view(s)

10-04-2018, 03:02 PM

shiftsuper175607 replied to a thread Oil leak in Walker Forum

How can anyone tell you without... 1)crystal ball 2) pictures 3)make and model of engine

7 replies | 187 view(s)

10-04-2018, 02:59 PM

shiftsuper175607 replied to a thread Dixon Ultra 61 Electrical in Kohler Engine Forum

Should be able to find one easily.... ...

1 replies | 51 view(s)

10-03-2018, 06:53 PM

shiftsuper175607 replied to a thread Decisions Decisions in John Deere Forum

Reading your post...sounds to me like you have made up your mind.

5 replies | 231 view(s)

10-03-2018, 08:32 AM

shiftsuper175607 replied to a thread zero turn will not turn left in Small Engine & Mower Repair

Will it go straight at speed?

4 replies | 128 view(s)

10-03-2018, 08:24 AM

shiftsuper175607 replied to a thread John Deere GT275 starting intermittently. in Small Engine & Mower Repair

If wiggling the key makes a difference...yes, check your switch. Find the hot wire on the back of the ignition switch... jumper it to the trigger...

1 replies | 66 view(s)

09-29-2018, 08:51 PM

shiftsuper175607 replied to a thread Cub cadet electrical issues in Small Engine & Mower Repair

Are you sure that is a ground wire? Is the solenoid grounded by the bolts holding it onto the frame?

1 replies | 67 view(s)

09-29-2018, 08:47 PM

shiftsuper175607 replied to a thread Turf Tiger - Removing front caster wheels...what am I missing? in Scag Forum

Should be good...it cost 4-5 times what some others cost.

6 replies | 144 view(s)

09-29-2018, 07:00 PM

shiftsuper175607 replied to a thread MS 250 Shortening of the chain? in Stihl Forum

Loosen the tension screw Now, loosen the two nuts that hold the bar... Slide the bar away from the engine to remove slack(wear gloves) Snug...

8 replies | 350 view(s)

09-29-2018, 06:46 PM

shiftsuper175607 replied to a thread possible carburetor fail??? in Troy-Bilt Forum

Check oil level in engine and see if possibly float hung and flooded engine with gas.

1 replies | 92 view(s)

09-29-2018, 06:37 PM

shiftsuper175607 replied to a thread Husqvarna YTH2042 Valve Adjustment Issue in Small Engine & Mower Repair

Single cylinder? Bad connection/corrosion at battery wire can be bad inside terminal battery bad...can even show good volatage solenoid bad ...

16 replies | 537 view(s)

09-29-2018, 01:30 PM

shiftsuper175607 replied to a thread Throttle backs off automatically BobCat Procat 61 in Small Engine & Mower Repair

Is the throttle cable moving?

3 replies | 112 view(s)

09-29-2018, 01:22 PM

shiftsuper175607 replied to a thread Sears push mower only starts with starting fluid in Briggs & Stratton Forum

choke not closing on starting It should restart when hot\\linkage not hooked up correctly

2 replies | 97 view(s)

09-29-2018, 01:21 PM

shiftsuper175607 replied to a thread stumped...oil filter housing in Build-it Yourself

I agree with John my Kubota, 26 yrs old, has no filter no problems, I just change the oil regularly.

12 replies | 411 view(s)

09-29-2018, 08:55 AM

shiftsuper175607 replied to a thread Nikki 791230 in Briggs & Stratton Forum

Did it have a plate on the carb you took off? What is the plate for? heat shield? How thick is it? Do you have gaskets for both sides of it?

9 replies | 215 view(s)

09-29-2018, 08:46 AM

shiftsuper175607 replied to a thread backfires in Snapper Forum

Your solenoid is good. Check valve lash clearances...OHV engine? Need engine numbers, please

2 replies | 96 view(s)

09-29-2018, 08:43 AM

shiftsuper175607 replied to a thread MTD B&S NON OHV 12.5 WON'T CRANK HOT in Small Engine & Mower Repair

Jumper solenoid with a screw driver by placing the blade FIRMLY on large nuts and see if there is any different in it trying to start. You don't...

5 replies | 141 view(s)

09-26-2018, 10:35 PM

shiftsuper175607 replied to a thread Murray will only start with Starter fluid in Murray Forum

Choke not fully closing so there is not enough suction to pull fuel into engine. If it will run continuously as long as you spray starting...

3 replies | 176 view(s)

09-24-2018, 01:08 PM

shiftsuper175607 replied to a thread New engine vibrates in Briggs & Stratton Forum

I would contact B & S and ask for technical support.

4 replies | 140 view(s)

09-24-2018, 01:00 PM

shiftsuper175607 replied to a thread How to check voltage or amps from solenoid to starter in Murray Forum

The wire from the battery runs straight to the solenoid...the connection at the + side of battery and the solenoid connection are the ones to check....

6 replies | 169 view(s)

shiftsuper175607

1,000 Post Club

Mini Statistics

Recent Visitors

Basic Information

Me, My Lawn and My Mower

Statistics

Total Posts

General Information

Free Membership Includes

shiftsuper175607 1,000 Post Club

Mini Statistics

Recent Visitors

Basic Information

Me, My Lawn and My Mower

Statistics

Total Posts

General Information

Free Membership Includes

Member Log In

Sign Up Now!

shiftsuper175607

1,000 Post Club