Craftsman lawn tractor wont start

suthnbell

Forum Newbie
Joined
Sep 29, 2012
Threads
1
Messages
1
My 21.5HP lawn tractor wont start. The following reasons lead me to believe it is clutch/brake related.
1. The brake does not work at all.
2. The tractor rolls freely while in gear
The battery is fine, makes a little sound when turning the key to start but wont turn over
 

Steve2000

Member
Joined
Aug 21, 2012
Threads
3
Messages
14
Is it the starter motor making the sound? Is it just a click or is it a steady noise?
 

DaveTN

Well-Known Member
Joined
Jun 12, 2011
Threads
16
Messages
668
If the tractor is rolling "freely in gear", I would check to make sure the belt is on. Some of those Craftsman mowers have a brake / clutch combination pedal. My neighbor took a ride on his Craftsman mower down a steep bank one day when the belt came off. Didn't matter if he was in gear or not, he was freewheeling fast!! Don't know about the starter part but will give it some thought.
 

Rivets

Lawn Royalty
Joined
Mar 11, 2012
Threads
55
Messages
14,681
Free wheeling does not have anything to do with starting, that is another problem. Try this on your starting problem.



Electrical* problems can be very easy or very difficult, depending on four things.
1. * How well you understand basic electricity.
2. *What tools you have and know how to use.
3. *How well you follow directions.
4. *You don't overlook or assume anything and verify everything.

Remember we cannot see what you are doing. *You are our eyes, ears and fingers in solving this problem. *You must be as accurate as you can when you report back. *The two basic tools we will ask you to use are a test light and a multi-meter. *If you have an assistant when going through these tests it would be very helpful. *These steps work the best when done in order, so please don't jump around. *Now let's solve this problem.

First, check the fuse(s), check battery connections for corrosion (clean if necessary) and *voltage - above 12.5 volts should be good.*

Second, check for power from the battery to one of the large terminals on the solenoid. *One of the wires is connected directly to the battery and has power all the time so one of the large terminals should light a test light or show 12 volts on a meter at all times.*

Third, *check for power at the small terminal of the solenoid while depressing the clutch/brake pedal and holding the key in the start position (you may need an assistant to sit in the seat to override the safety switch). If your solenoid is a four wire solenoid, check both small wire terminals as one is ground and the other is power from the ignition switch. *If your solenoid is a three wire solenoid, make sure the solenoid body is not corroded where it bolts to the chassis of the mower as this is your ground path back to the battery. *If in doubt, remove the solenoid and clean the mounting area down to bare metal. *If there is no power to the small terminal then your problem is most likely a safety switch, ignition switch or in the wiring.*

Fourth, check for power on the other large terminal of the solenoid while holding the key in the start position (you may need an assistant to sit in the seat to override the safety switch).*

Fifth, check for power at the starter while holding the key in the start position (assistant again).*

Sixth, check your ground circuit back to the battery.

After you have gone through each of the above steps, let us know what happened when you did each step. *At that point we will have great info to tell you how to proceed. *Remember you are our eyes, ears, and fingers, so please be as accurate as possible.

Be as specific as possible with voltage readings as this will help diagnose your problem quicker. *If you do not know how to perform the above checks, just ask and I will try to guide you through it. *Youtube also has some videos and as you know a picture is worth a thousand words.
 
Top